Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2019.09
RM32K0E _59 Vehicle Exterior _061789 WIPER / WASHER _0301221 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK WINDSHIELD WIPER RELAY ASSEMBLY


E257545N10
3.396,0.177 3.792,0.417 0.396,0.24 3.469,0.219 4.073,0.49 0.604,0.271 10 false F56

a.

Disconnect the F56 windshield wiper relay assembly connector.

i.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
F56-2 (IG) - Body ground B - Body ground Power switch on (IG) signal (Power source circuit) Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
F56-25 (W) - Body ground B - Body ground Front washer switch signal Front washer switch on Below 1 Ω
Front washer switch off 10 kΩ or higher
F56-8 (VR2) - F56-21 (VR1) W - G Adjusting volume signal Controlling sensitivity setting switch* changed 0 to 231 Ω
F56-12 (E) - Body ground W-B - Body ground Body ground Always Below 1 Ω
F56-16 (WIG) - Body ground B - Body ground Power source signal Power switch on (IG) 11 to 14 V
Power switch off Below 1 V

HINT:

*: The rain sensor sensitivity can be adjusted by the controlling sensitivity setting switch.

If the result is not as specified, there may be a malfunction in the wire harness.




b.

Reconnect the F56 windshield wiper relay assembly connector.

i.

Measure the resistance according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
F56-10 (+1) - Body ground G - Body ground Front wiper motor low speed signal Front wiper motor off Below 1 Ω

HINT:

If the result is not as specified, the windshield wiper relay assembly may be malfunctioning.



ii.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
F56-1 (+SM) - Body ground G - Body ground Front wiper motor position detection signal Front wiper motor in low or high operation Below 1 V ←→ 11 to 14 V
Front wiper motor off Below 1 V
F56-3 (C1) - F56-5 (CO) V - Y Front wiper switch AUTO signal Power switch on (IG), front wiper switch in AUTO Below 1 V
Power switch on (IG), front wiper switch off 11 to 14 V
F56-25 (W) - Body ground B - Body ground Front washer switch signal Power switch on (IG), front washer switch on Below 1 V
Power switch on (IG), front washer switch off 11 to 14 V
F56-10 (+1) - Body ground G - Body ground Front wiper motor low speed signal Front wiper motor in low operation 11 to 14 V
F56-11 (+2) - Body ground W - Body ground Front wiper motor high speed signal Front wiper motor in high operation 11 to 14 V
Front wiper motor off Below 1 V
F56-14 (MPX1) - Body ground V - Body ground Rain sensor signal Power switch on (IG) Pulse generation
F56-24 (SPD) - Body ground V - Body ground Vehicle speed signal Driving at approximately 20 km/h (12 mph) Pulse generation (See waveform 1)

HINT:

If the result is not as specified, the windshield wiper relay assembly may be malfunctioning.



iii.
E267248E01
2.969,1.229 3.354,1.427 0.385,0.198 10 false GND 1.156,1.667 1.333,1.865 0.177,0.198 10 false A

Waveform 1 (Reference):

Item Condition
Tester Connection F56-24 (SPD) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.





CHECK COMBINATION METER ASSEMBLY


E308357E04
2.24,0.365 2.594,0.573 0.354,0.208 4.948,0.375 5.313,0.594 0.365,0.219 2.344,0.385 2.656,0.583 0.313,0.198 10 false F4 5.042,0.406 5.354,0.604 0.313,0.198 10 false F5

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F4-17 (WLVL)* - Body ground LG - Body ground Washer fluid level signal Power switch on (IG), washer fluid level not low 11 to 14 V
Power switch on (IG), washer fluid level low Below 1 V

*: w/ Washer Fluid Warning System



b.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F4-6 (+S) - Body ground V - Body ground Speed signal for other system (Output) Driving at approximately 20 km/h (12 mph) Pulse generation (See waveform 1)

i.
E267248E01
2.969,1.229 3.354,1.427 0.385,0.198 10 false GND 1.156,1.667 1.333,1.865 0.177,0.198 10 false A

Waveform 1 (Reference):

Item Condition
Tester Connection F4-6 (+S) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.





HEADLIGHT ECU SUB-ASSEMBLY RH (for Single Beam Headlight with Headlight Cleaner System)


a.

Disconnect the A17 headlight ECU sub-assembly RH connector.

E298707N36
3.385,0.135 3.75,0.375 0.365,0.24 3.458,0.177 3.917,0.375 0.458,0.198 10 false A17


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A17-4 (IG) - Body ground V - Body ground IG power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A17-12 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω


c.

Reconnect the A17 headlight ECU sub-assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A17-7 (HLC) - Body ground W - Body ground Headlight cleaner motor operation signal Headlight cleaner motor not operating 11 to 14 V
Headlight cleaner motor operating Below 1 V
A17-18 (FRWA) - Body ground R - Body ground Front washer switch signal Power switch on (IG), front washer switch on 11 to 14 V
Power switch on (IG), front washer switch off Below 1 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for Triple Beam Headlight with Headlight Cleaner System)


B434105C67
2.146,3.302 2.51,3.521 0.365,0.219 4.625,3.302 4.979,3.51 0.354,0.208 1.365,4.719 1.719,4.948 0.354,0.229 3.75,4.698 4.094,4.917 0.344,0.219 5.313,4.823 5.656,5.01 0.344,0.188 6.313,4.833 6.635,5.042 0.323,0.208 1.521,6.344 1.896,6.552 0.375,0.208 4.667,6.354 5,6.563 0.333,0.208 3.385,7.948 3.802,8.156 0.417,0.208 1.594,0.646 1.594,0.302 1.594,0.302 1.719,0.302 false 1.677,1.844 1.927,1.844 true 1.677,1.479 1.927,1.479 true 1.417,2.729 1.417,1.469 1.417,1.469 1.542,1.469 false 1.417,1.844 1.542,1.844 false 4.052,0.802 4.052,0.292 4.052,0.292 4.219,0.292 true 0.865,1.083 1.177,1.281 0.313,0.198 10 false 3H 0.875,1.667 1.188,1.865 0.313,0.198 10 false 3F 0.875,2.01 1.188,2.208 0.313,0.198 10 false 3L 0.885,2.229 1.198,2.427 0.313,0.198 10 false 3K 1.771,0.219 2.083,0.417 0.313,0.198 10 false *1 1.958,1.396 2.417,1.594 0.458,0.198 10 false F16 1.958,1.76 2.417,1.958 0.458,0.198 10 false F15 1.344,2.771 1.656,2.969 0.313,0.198 10 false *a 4.302,0.208 4.615,0.406 0.313,0.198 10 false MB 5.833,1.094 6.042,1.302 0.208,0.208 10 false 3D 5.844,1.771 6.156,1.969 0.313,0.198 10 false 3A 2.219,3.333 2.677,3.531 0.458,0.198 10 false F16 4.688,3.333 5.146,3.531 0.458,0.198 10 false F15 1.448,4.75 1.76,4.948 0.313,0.198 10 false 3H 3.833,4.729 4.146,4.927 0.313,0.198 10 false 3F 5.417,4.844 5.729,5.042 0.313,0.198 10 false 3L 6.365,4.854 6.677,5.052 0.313,0.198 10 false 3K 1.594,6.354 1.906,6.552 0.313,0.198 10 false 3D 4.729,6.375 5.042,6.573 0.313,0.198 10 false 3A 3.479,7.99 3.792,8.188 0.313,0.198 10 false MB 0.188,0.198 0.5,0.396 0.313,0.198 10 false *A
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 Connectors - -


B434104C55
3.542,3.229 3.917,3.49 0.375,0.26 1.385,4.708 1.719,4.938 0.333,0.229 3.656,4.708 4.021,4.938 0.365,0.229 5.333,4.813 5.635,5.021 0.302,0.208 6.302,4.802 6.635,5.031 0.333,0.229 1.521,6.271 1.865,6.521 0.344,0.25 4.719,6.323 5.115,6.563 0.396,0.24 3.115,7.865 3.469,8.115 0.354,0.25 1.615,0.656 1.615,0.281 1.615,0.281 1.74,0.281 false 1.677,1.365 1.938,1.365 true 1.417,2.792 1.417,1.365 1.417,1.365 1.542,1.365 true 4.021,0.802 4.021,0.313 4.021,0.313 4.177,0.313 true 0.875,1.094 1.188,1.292 0.313,0.198 10 false 3H 0.885,1.667 1.198,1.865 0.313,0.198 10 false 3F 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3L 0.896,2.25 1.208,2.448 0.313,0.198 10 false 3K 1.813,0.219 2.125,0.417 0.313,0.198 10 false *1 1.99,1.281 2.448,1.479 0.458,0.198 10 false F15 1.354,2.844 1.667,3.042 0.313,0.198 10 false *a 4.229,0.25 4.542,0.448 0.313,0.198 10 false MB 5.844,1.115 6.156,1.313 0.313,0.198 10 false 3D 5.844,1.74 6.156,1.938 0.313,0.198 10 false 3A 3.604,3.281 3.917,3.479 0.313,0.198 10 false F15 1.479,4.74 1.792,4.938 0.313,0.198 10 false 3H 3.76,4.74 4.073,4.938 0.313,0.198 10 false 3F 5.396,4.833 5.708,5.031 0.313,0.198 10 false 3L 6.354,4.844 6.667,5.042 0.313,0.198 10 false 3K 1.594,6.323 1.906,6.521 0.313,0.198 10 false 3D 4.813,6.375 5.125,6.573 0.313,0.198 11 false 3A 3.188,7.917 3.5,8.115 0.313,0.198 10 false MB 0.156,0.167 0.469,0.365 0.313,0.198 10 false *A
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 1 Connector - -


a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3F-31 - Body ground G - Body ground Low beam headlight signal Light control switch in head position Below 1 V
Light control switch off 4.2 V or higher

If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.