Home › General › MAINTENANCE › 2ZR-FXE OIL AND OIL FILTER › from 2019.09
RM32K0E _V1 General _059911 MAINTENANCE _0298538 2ZR-FXE OIL AND OIL FILTER A

MAINTENANCE  2ZR-FXE OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 1.REMOVE CENTER NO. 4 ENGINE UNDER COVER

a.
A390268

Remove the 4 screws and center No. 4 engine under cover.


Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly.


b.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


c.

Clean the oil pan drain plug.


d.

Install a new gasket to the oil pan drain plug.


e.

Install the oil pan drain plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 3.REMOVE OIL FILTER

a.

Using SST, remove the oil filter sub-assembly.

SST
09228-06502  


Hide 4.INSTALL OIL FILTER

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.

Using SST, tighten the oil filter sub-assembly.

SST
09228-06502  

Depending on the work space available, choose from the following:
·

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.


Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)

·

If not enough space is available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or use a common wrench.



Hide 5.ADD ENGINE OIL

a.

Destination package for Europe:

i.

Add new engine oil and install the oil filler cap assembly.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SN " Resource-Conserving"or SN PLUS "Resource-Conserving" multigrade engine oil
·

0W-16


API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or SN PLUS "Resource-Conserving", or ILSAC multigrade engine oil
·

0W-20

·

5W-30

·

10W-30


API grade SL, SM, SN or SN PLUS multigrade engine oil
·

15W-40



Standard Capacity:
Item Standard Condition
Drain and refill with oil filter change 4.3 liters (4.5 US qts, 3.8 Imp. qts)
Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 Imp. qts)
Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)



b.

except Europe:

i.

Add new engine oil and install the oil filler cap sub-assembly.

Standard Oil Grade
Oil Grade Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or SN PLUS "Resource-Conserving", or ILSAC multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30


API grade SL, SM, SN or SN PLUS multigrade engine oil
·

15W-40



Standard Capacity:
Item Standard Condition
Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 Imp. qts)
Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 Imp. qts)
Dry fill 4.7 liters (5.0 US qts, 4.1 Imp. qts)



Hide 6.INSPECT FOR OIL LEAK

a.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


b.

Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.


Hide 8.INSTALL CENTER NO. 4 ENGINE UNDER COVER

a.

Install the center No. 4 engine under cover with the 4 screws.