Home › Engine / Hybrid System › M20A-FXS (LUBRICATION) › OIL PUMP › from 2019.09
RM32K0E _51 Engine / Hybrid System _083956 M20A-FXS LUBRICATION _0404357 OIL PUMP G

M20A-FXS LUBRICATION  OIL PUMP  INSPECTION  


PROCEDURE

Hide 1.INSPECT OIL PUMP RELIEF VALVE

a.
A426275

Coat the oil pump relief valve with engine oil, then check that it falls smoothly into the valve hole by its own weight.

HINT:

If the oil pump relief valve does not fall smoothly, replace the oil pump assembly.



Hide 2.INSPECT OIL PUMP ROTOR

a.

Check the side clearance (Oil pump driven rotor side).

i.
A426276C03
1.031,0.667 1.365,0.667 false 2.323,1.688 2.698,1.49 false 0.396,2.24 0.573,2.24 false 0.844,0.563 1.156,0.719 0.313,0.156 10 false *1 0.208,2.156 0.521,2.313 0.313,0.156 10 false *2 2.542,0.573 2.854,0.729 0.313,0.156 10 false *a 2.208,2.031 2.396,2.208 0.188,0.177 10 true *b 2.719,1.396 3.031,1.552 0.313,0.156 10 false *c
*1 Oil Pump Driven Rotor
*2 Oil Pump Body
*a Width
*b Depth
*c Straightedge


Using a vernier caliper, measure the width of the oil pump driven rotor.

HINT:

Perform the measurement at 3 random places.



ii.

Using a vernier caliper and precision straightedge, measure the depth of the oil pump body.

NOTICE:

Make sure to deduct the thickness of the precision straightedge.


HINT:

Perform the measurement at 3 random places.



iii.

Subtract the oil pump driven rotor width measurement from the oil pump body depth measurement.

Standard Side Clearance:

0.025 to 0.070 mm (0.000984 to 0.00276 in.)


HINT:

If the result is not as specified, replace the oil pump assembly.




b.

Check the side clearance (Oil pump regulator ring side).

i.
A426277C01
0.833,0.833 1.167,0.833 false 0.646,1.75 0.979,1.75 false 2.313,1.688 2.667,1.5 false 0.646,0.719 0.958,0.875 0.313,0.156 10 false *1 0.427,1.635 0.74,1.792 0.313,0.156 10 false *2 2.896,0.938 3.208,1.094 0.313,0.156 10 false *a 2.208,2.021 2.396,2.208 0.188,0.188 10 true *b 2.719,1.396 3.031,1.552 0.313,0.156 10 false *c
*1 Oil Pump Regulator Ring
*2 Oil Pump Body
*a Width
*b Depth
*c Straightedge


Using a vernier caliper, measure the width of the oil pump regulator ring.

HINT:

Perform the measurement at 3 random places.



ii.

Using a vernier caliper and precision straightedge, measure the depth of the oil pump body.

NOTICE:

Make sure to deduct the thickness of the precision straightedge.


HINT:

Perform the measurement at 3 random places.



iii.

Subtract the oil pump regulator ring width measurement from the oil pump body depth measurement.

Standard Side Clearance:

0.025 to 0.075 mm (0.000984 to 0.00295 in.)


HINT:

If the result is not as specified, replace the oil pump assembly.