DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Warm up the engine.
Turn the A/C switch off.
Turn the power switch off.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Ptrl General / -
Ptrl AF Control / Air fuel ratio control system related data
Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
Ptrl Throttle / Gasoline throttle system related data
Ptrl Intake Control / Intake control system related data
Ptrl Valve Control / Valve control system related data
Ptrl Misfire / "Misfire" related data
Ptrl Starting / "Difficult to start" related data
Ptrl Rough Idle / "Rough idle" related data
Ptrl Evaporative / Evaporative system related data
Ptrl CAT Converter / Catalytic converter related data
Check Mode / Check mode related data
Monitor Status / Monitor status related data
Ignition / Ignition system related data
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transaxle system related data
Vehicle Information / Vehicle information
Read the Data List according to the display on the GTS.
The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all of the Data List items listed for that group will be displayed.
Various Vehicle Conditions 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | This is the current vehicle speed. |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 950 to 1050 rpm: Idling with warmed up engine (inspection mode [maintenance mode], not charge control, park (P) selected) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM | Min.: 0%, Max.: 100% | ·
20 to 40%: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) ·
15 to 35%: Warmed up engine, 2500 rpm (inspection mode [maintenance mode]) |
·
This is the engine load calculated based on the estimated intake manifold pressure. ·
Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the actual intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) |
| Vehicle Load | Vehicle load | Min.: 0%, Max.: 25700% | Actual vehicle load | ·
This is the engine intake air charging efficiency. ·
Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow x 100 (%) Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)
|
| Mass Air Flow Sensor | Airflow rate from mass air flow meter | Min.: 0 gm/sec, Max.: 655.35 gm/sec | ·
1.0 to 3.0 gm/sec: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) ·
4.5 to 8.5 gm/sec: Warmed up engine, 2500 rpm (inspection mode [maintenance mode]) |
This is the intake air amount measured by the mass air flow meter. |
| Atmospheric Pressure | Atmospheric pressure | Min.: 0 kPa (0 psi), Max.: 255 kPa (37 psi) | Equivalent to atmospheric pressure | ·
This value is calculated based on the atmospheric pressure sensor. ·
Standard atmospheric pressure: 101 kPa(abs) [15 psi(abs)] ·
For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (0.1 psi). This varies depending on the weather. |
| Intake Manifold Absolute Pressure | Intake manifold absolute pressure | Min.: 0 kPa (0 psi), Max.: 2047.96 kPa (296.95 psi) | ·
80 to 110 kPa(11.6 to 15.95 psi): Power switch on (IG) ·
20 to 40 kPa(2.9 to 5.8 psi): Idling with warmed up engine (inspection mode [maintenance mode], not charge control) |
·
This is the intake manifold pressure. ·
This item is the pressure detected by the manifold absolute pressure sensor and is used for air fuel ratio control and EGR valve control.
|
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Intake Air Temperature | Intake air temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to temperature at location of mass air flow meter | This is the engine intake air temperature.
|
| Engine Run Time | Engine run time | Min.: 0 sec, Max.: 65535 sec | Time after engine start | ·
This is the time elapsed since the engine is first started with the power switch on (READY). ·
With the power switch on (READY), time measurement will not stop even after the engine stops. |
| Heater Coolant Temperature Sensor | Engine coolant temperature | Min.: -40°C (-40°F), Max.: 215°C (419°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| IG-ON Coolant Temperature | Engine coolant temperature when the power switch is turned on (IG) | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the engine coolant temperature stored when the power switch is turned on (IG). |
| Initial Engine Coolant Temperature | Engine coolant temperature when the power switch is turned on (READY) | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the engine coolant temperature stored when the power switch is turned on (READY). |
| IG-ON Intake Air Temperature | Intake air temperature when the power switch is turned on (IG) | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the intake air temperature stored when the power switch is turned on (IG). |
| Initial Engine Intake Air Temperature | Intake air temperature when the power switch is turned on (READY) | Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) | - | This is the intake air temperature stored when the power switch is turned on (READY). |
| Battery Voltage | Auxiliary battery voltage | Min.: 0 V, Max.: 65.5 V | 11 to 16 V: Power switch on (IG) | If 11 V or less, characteristics of some electrical components may change. |
| BATT Voltage | Auxiliary battery voltage | Min.: 0 V, Max.: 79.998 V | 11 to 16 V: Power switch on (IG) | If 11 V or less, characteristics of some electrical components may change. |
Throttle Control (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Throttle Position Sensor No.1 Voltage % | Absolute No. 1 throttle position sensor | Min.: 0%, Max.: 100% | 10 to 22%: Power switch on (IG), accelerator pedal fully released | The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Throttle Position Sensor No.2 Voltage % | Absolute No. 2 throttle position sensor | Min.: 0%, Max.: 100% | 42 to 62%: Power switch on (IG), accelerator pedal fully released | The No. 2 throttle position sensor output is converted using 5 V = 100%. |
| System Guard | System guard | ON or OFF | ON: Idling or throttle actuator operating | ·
When there is a difference between the target and actual throttle valve opening angle, this item changes to OFF and the electronic throttle control system operation is disabled. ·
OFF: Electronic throttle control is stopped. ·
After the power switch is turned on (READY), OFF will be displayed until the throttle valve is first operated. |
| Open Side Malfunction | Open malfunction | ON or OFF | OFF | This item indicates a malfunction in the electronic throttle when the throttle valve is open. |
| Throttle Request Position | Required throttle position | Min.: 0 V, Max.: 4.98 V | 0.6 to 1.1 V: Idling with warmed up engine (inspection mode [maintenance mode]) | The value of this item is calculated by the ECM and shows the voltage for the target throttle valve position. |
| Throttle Sensor Position | Throttle sensor position | Min.: 0%, Max.: 100% | - | - |
| Throttle Position Sensor No.1 Voltage | No. 1 throttle position sensor output voltage | Min.: 0 V, Max.: 4.98 V | ·
0.6 to 1.1 V: Power switch on (IG), accelerator pedal fully released ·
0.6 to 1.4 V: Fail-safe operating |
This is the No. 1 throttle position sensor output voltage. |
| Throttle Position Sensor No.2 Voltage | No. 2 throttle position sensor output voltage | Min.: 0 V, Max.: 4.98 V | ·
2.1 to 3.1 V: Power switch on (IG), accelerator pedal fully released ·
2.1 to 3.1 V: Fail-safe operating |
This is the No. 2 throttle position sensor output voltage. |
| Throttle Position Command | Throttle position command value | Min.: 0 V, Max.: 4.98 V | 0.6 to 1.1 V: Idling with warmed up engine (inspection mode [maintenance mode]) | The value displayed for this item is the same as Throttle Request Position. |
| Throttle Position Sensor Open Position No.1 | No. 1 throttle position sensor | Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | This is the No. 1 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released the throttle valve is kept open by the throttle valve opener when the power switch is on (IG). |
| Throttle Position Sensor Open Position No.2 | No. 2 throttle position sensor | Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | This is the No. 2 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released the throttle valve is kept open by the throttle valve opener when the power switch is on (IG). |
| Throttle Motor Current | Throttle actuator current | Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling with warmed up engine (inspection mode [maintenance mode]) | When the value of this item is large but the actual opening angle (Throttle Position Sensor No.1 Voltage) does not reach the target opening angle (Throttle Request Position), there is an "unable to open" malfunction. |
| Throttle Motor Duty Ratio | Throttle actuator | Min.: 0%, Max.: 100% | 10 to 22%: Idling with warmed up engine (inspection mode [maintenance mode]) | This is the output duty ratio of the throttle actuator drive circuit. |
| Throttle Motor Duty Ratio (Open) | Throttle actuator duty ratio (open) | Min.: 0%, Max.: 255% | 0 to 40%: Idling with warmed up engine (inspection mode [maintenance mode]) | This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal. |
| Throttle Motor Duty Ratio (Close) | Throttle actuator duty ratio (close) | Min.: 0%, Max.: 255% | 0 to 40%: Idling with warmed up engine (inspection mode [maintenance mode]) | This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
|
| Throttle Position Sensor Fully Closed Learn Value | Throttle valve fully closed position (learned value) | Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Power switch on (IG), accelerator pedal fully released | ·
The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. The ECM calculates the learned value based on the position of the throttle valve when the accelerator pedal is released and the throttle valve motor is not operating. ·
Learning is performed immediately after the power switch is turned on (IG). |
| +BM Voltage | +BM voltage | Min.: 0 V, Max.: 79.998 V | 11 to 16 V: Power switch on (IG) | This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P065714 (open circuit) and P06579E (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the power switch is turned off). |
| Actuator Power Supply | Actuator power supply | ON or OFF | ON: Engine running or throttle actuator operating | - |
| Throttle Air Flow Learn Value (Area 1) | Throttle air flow learning value of area 1 | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Area 2) | Throttle air flow learning value of area 2 | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Area 3) | Throttle air flow learning value of area 3 | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Calculated Value) | Throttle air flow learning value (calculated value) | Min.: 0, Max.: 1.99 | - | - |
| Throttle Air Flow Learn Value (Atmosphere Pressure Offset Value) | Throttle air flow learning value (atmosphere pressure offset value) | Min.: 0, Max.: 2.55 | - | - |
Idle Speed Control (Ptrl Rough Idle)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Low Revolution Control | Low engine speed control operation state | ON or OFF | OFF | This item indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. |
| Engine Stall Control F/B Flow | ISC torque lower limit value to prevent engine stall | Min.: -1024 Nm, Max.: 1023.96 Nm | - | ·
The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent the engine from stalling. ·
For use when the starting problems or rough idle is present. |
Fuel System (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Injector Cylinder #1 (Port) | Injection period of the No. 1 cylinder | Min.: 0 μs, Max.: 65535 μs | 1000 to 3000 μs: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | This is the injection period of the No. 1 cylinder (the command value from the ECM). |
| Injection Volume Cylinder #1 | Injection volume (cylinder 1) | Min.: 0 ml, Max.: 2 ml | 0.03 to 0.13 ml: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | This is the fuel injection volume for 10 injections. |
| Injection Volume | Fuel injection volume | Min.: -25%, Max.: 24.8% | - | Active Test [Control the Injection Volume for A/F Sensor] support data. |
| Fuel Pump/Speed Status | Fuel pump status | ON or OFF | ON: Engine running | - |
| Current Fuel Type | Current fuel type | - | Gasoline/petrol | - |
EVAP System (Ptrl Evaporative)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| EVAP (Purge) VSV | Purge VSV control duty | Min.: 0%, Max.: 100% | 10 to 70%: Idling with warmed up engine (inspection mode [maintenance mode]) | ·
This is the command signal from the ECM. ·
This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed. *: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV. ·
When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV will be 0%. |
| EVAP Purge Flow | Purge flow | Min.: 0%, Max.: 399.9% | - | This is the percentage of total engine airflow contributed by EVAP purge operation.
(Evap Purge Flow = Purge flow / Engine airflow x 100 (%)) |
| EVAP Purge Density Learn Value | Purge density learned value | Min.: -200, Max.: 199.993 | - | ·
This is the proportion of the decrease in injection volume (based on the change in the air fuel ratio feedback compensation value) related to a 1% purge flow rate. ·
When the value of this item is a large negative value, the purge effect is large. ·
The purge density is determined from the change in the air fuel ratio feedback compensation value when purge flow is introduced. ·
Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
|
| Fuel Lid SW | Fuel lid courtesy switch status | Open or Close | ·
Open: Fuel lid opener switch pushed ·
Close: Fuel lid opener switch not pushed |
- |
| EVAP Purge VSV | VSV status for EVAP control | ON or OFF | - | This item is ON when EVAP (Purge) VSV is approximately 30% or higher, and is OFF when the VSV duty ratio is less than 30%. |
| Purge Cut VSV Duty | Purge VSV duty | Min.: 0%, Max.: 399.9% | - | - |
Air Fuel Ratio Control 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Air-Fuel Ratio | Target air fuel ratio | Min.: 0, Max.: 2 | 0.8 to 1.2: During idling (engine warmed up) | ·
This is the target air fuel ratio used by the ECM. ·
1.0 is the stoichiometric air fuel ratio. Values that are more than 1.0 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1.0 indicate the system attempting to make the air fuel ratio richer. ·
Target Air-Fuel Ratio and A/F (O2) Lambda Sensor B1S1 are related. |
Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/F (O2) Lambda Sensor B1S1 | Output air fuel ratio associated | Min.: 0, Max.: 1.99 | ·
Value less than 1 (0.000 to 0.999) = Rich ·
1 = Stoichiometric air fuel ratio ·
Value more than 1 (1.001 to 1.999) = Lean |
This is the actual air fuel ratio calculated based on the air fuel ratio sensor output. |
| A/F (O2) Sensor Voltage B1S1 | Air fuel ratio sensor output voltage | Min.: 0 V, Max.: 7.99 V | 2.6 to 3.8 V: Idling with warmed up engine (inspection mode [maintenance mode]) | ·
This is the output voltage of the air fuel ratio sensor (the voltage cannot be measured at the terminals of the sensor). This value is calculated by the ECM based on the current output of the air fuel ratio sensor (refer to A/F (O2) Sensor Current below for the actual sensor output). ·
Performing the "Control the Injection Volume or Control the Injection Volume for A/F Sensor" Active Test enables the technician to check the output voltage of the sensor. |
| A/F (O2) Sensor Current B1S1 | Air fuel ratio sensor output current | Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling with warmed up engine (inspection mode [maintenance mode]) | ·
With a stoichiometric air fuel ratio (for example, during idling after the engine is warmed up), the air fuel ratio sensor current output is approximately -0.5 to 0.5 mA. ·
When the value is outside the range of 0.7 to 2.2 mA when the fuel-cut is being performed, there is a malfunction in the air fuel ratio sensor or sensor circuit. |
| A/F (O2) Sensor Heater Duty Ratio B1S1 | Air fuel ratio sensor heater duty ratio | Min.: 0%, Max.: 399.9% | 0 to 100% | When the value of this item is more than 0%, current is being supplied to the heater. |
| O2 Sensor Voltage B1S2 | Heated oxygen sensor output voltage | Min.: 0 V, Max.: 1.275 V | 0 to 1.0 V | ·
This is the output voltage of the heated oxygen sensor. ·
Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio. ·
Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio. ·
During air fuel ratio feedback control, the value moves back and forth between 0 and 1 V. ·
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" Active Test enables the technician to check output voltage of the sensor. |
| O2 Sensor Impedance B1S2 | Heated oxygen sensor impedance | Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm | - |
| O2 Sensor Heater B1S2 | Heated oxygen sensor heater | Active or Not Act | Active: Heater on | - |
| O2 Sensor Heater Current Value B1S2 | Heated oxygen sensor current | Min.: 0 A, Max.: 4.999 A | - | When the value of this item is more than 0 A, current is being supplied to the heater. |
| Short FT B1S1 | Short-term fuel trim | Min.: -100%, Max.: 99.21% | -20 to 20% | This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the air fuel ratio sensor for feedback. |
| Long FT B1S1 | Long-term fuel trim | Min.: -100%, Max.: 99.21% | -20 to 20% | ·
The ECM will learn the Long FT B1S1 values based on Short FT B1S1. The goal is to keep Short FT B1S1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio. ·
This item is used to determine whether the system related to air fuel ratio control is malfunctioning. ·
The condition of the system is determined based on the sum of Short FT B1S1 and Long FT B1S1 (excluding times when the system is in transition). -
20% or higher: The air fuel ratio may be lean. -
-20 to 20%: The air fuel ratio can be determined to be normal. -
-20% or less: The air fuel ratio may be rich. -
Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and a separate value is stored for each operating range. "Long FT B1S1" indicates the learned value for the current operating range. [A/F Learn Value Idle Bank 1], [A/F Learn Value Low Bank 1], [A/F Learn Value Mid No.1 Bank 1], [A/F Learn Value Mid No.2 Bank 1] and [A/F Learn Value High Bank 1] indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT B1S1" indicates the current engine operating range. |
| Total FT Bank 1 | Total fuel trim | Min.: -0.5, Max.: 0.496 | -0.28 to 0.2: Idling with warmed up engine (inspection mode [maintenance mode]) | Total FT Bank 1 = Short FT B1S1 + Long FT B1S1 |
| Fuel System Status Bank 1 | Fuel system status (bank 1) | Unused, OL, CL, OLDrive, OLFault or CLFault | CL: Idling after warming up | ·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop. ·
CL (Closed Loop): Feedback for fuel control. ·
OLDrive: Open loop due to driving conditions (fuel enrichment). ·
OLFault: Open loop due to a detected system fault. ·
CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
|
| Fuel System Status Bank 2 | Fuel system status (bank 2) | Unused, OL, CL, OLDrive, OLFault or CLFault | Unused | - |
| A/F Learn Value Idle Bank 1 | Air fuel ratio learn value of idle area | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher). |
| A/F Learn Value Low Bank 1 | Air fuel ratio learn value of low load area | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.1 Bank 1 | Air fuel ratio learn value of middle 1 load area | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the medium load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid No.2 Bank 1 | Air fuel ratio learn value of middle 2 load area | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the medium load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High Bank 1 | Air fuel ratio learn value of high load area | Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
Ignition System (Ignition)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Timing Cylinder #1 | Ignition timing advance for No. 1 cylinder | Min.: -64 deg, Max.: 63.5 deg | 8 to 24 deg: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | - |
| Knock F/B Value | Knocking feedback value | Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | -20 to 0 deg(CA): Driving at 70 km/h (43 mph) (Engine running) | This is the ignition timing retard compensation amount determined by the presence or absence of knocking.
Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock F/B Value*3 + each compensation amount Example: 21 deg(CA) = 10 deg(CA) + 14 deg(CA) - 3 deg(CA) *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The knock correction learned value is calculated as shown below in order to keep Knock F/B Value as close to -3 deg(CA) as possible. When Knock F/B Value is less than -4 deg(CA), Knock Correct Learn Value is slowly decreased. When Knock F/B Value is higher than -2 deg(CA), Knock Correct Learn Value is slowly increased. *3: The base value is -3 deg(CA) and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.
|
| Knock Correct Learn Value | Knocking correction learned value | Min.: -1024 deg(CA), Max.: 1023.9 deg(CA) | 0 to 22 deg(CA): Driving at 70 km/h (43 mph) (Engine running) | ·
Refer to "Knock F/B Value". ·
When there is knocking or a lack of power, compare the values of following items to another vehicle of the same model. -
Engine Speed -
Calculate Load -
Ignition Timing Cylinder #1 -
Knock F/B Value -
Knock Correct Learn Value ·
Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced. ·
Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.
|
| Idle Spark Advance Control Cylinder #1 | Individual cylinder timing advance compensation amount (No. 1) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #2 | Individual cylinder timing advance compensation amount (No. 2) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #3 | Individual cylinder timing advance compensation amount (No. 3) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
| Idle Spark Advance Control Cylinder #4 | Individual cylinder timing advance compensation amount (No. 4) | Min.: 0 deg(CA), Max.: 15.93 deg(CA) | - | ·
This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling. ·
It may be possible to use this item to help determine specific cylinders which are not operating normally. |
Mass Air Flow Meter (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mass Air Flow Circuit | Status of the mass air flow meter circuit | Normal or Abnormal | Normal | - |
EGR System (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target EGR Valve Position No.1 | EGR valve target opening amount | Min.: 0%, Max.: 100% | 0%: Idling with warmed up engine (inspection mode [maintenance mode]) | ·
When the engine is cold or idling, at engine start, etc., the value is 0%. ·
When the valve is fully closed, the value is 0%. ·
When the valve is fully open, the value is 100%. |
| EGR Step Position | EGR step position | Min.: 0 step, Max.: 255 step | - | ·
Active Test [Control the EGR Step Position] support data. ·
When the valve is fully closed, the value is 0 step. ·
When the valve is fully open, the value is 110 step. |
| Clogged EGR Port Imbalance Ratio | EGR valve on (open)/off (fully closed) time imbalance ratio | Min.: 0, Max.: 2.55 | 0 to 0.9 | ·
If the value becomes 1.0 or more, DTC P10AA00 will be stored. ·
The highest recorded value will be displayed continuously until the DTCs are cleared or the cable is disconnected from the negative (-) auxiliary battery terminal. |
VVT Control (Ptrl Valve Control)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| VVT Advance Fail | VVT control failure status | ON or OFF | OFF: Idling | ON: There is an intake VVT timing advance malfunction. |
| Intake VVT Hold Learn Value Bank 1 | Intake VVT hold correct learned value | Min.: 0%, Max.: 399.9% | - | - |
| Intake VVT Change Angle Bank 1 | Intake VVT displacement angle | Min.: 0 DegFR, Max.: 639.9 DegFR | - | - |
| Intake VVT OCV Control Duty Ratio Bank 1 | Camshaft timing oil control valve operation duty | Min.: 0%, Max.: 399.9% | - | - |
| Intake VVT Target Angle Bank 1 | Intake VVT target angle | Min.: 0 DegFR, Max.: 639.9 DegFR | 10 DegFR: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) | - |
Catalyst (Ptrl CAT Converter)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Catalyst Temperature B1S1 | Front catalyst temperature | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | ·
This is the temperature of the front catalyst estimated by the ECM. ·
This item is included in the conditions used to detect catalyst deterioration (DTC P042000), etc., and should therefore be used as a reference when recreating malfunction conditions. |
| Catalyst Temperature B1S2 | Rear catalyst temperature | Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | This is the temperature of the rear catalyst estimated by the ECM. |
Check Mode (Check Mode)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Misfire Test Result | Check mode result for misfire monitor | Compl or Incmpl | - | - |
| O2 Sensor B1S2 Test Result | Check mode result for heated oxygen sensor | Compl or Incmpl | - | - |
| A/F (O2) Sensor B1S1 Test Results | Check mode result for air fuel ratio sensor | Compl or Incmpl | - | - |
Test Result (Monitor Status)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | ·
* |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | ·
* |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | ·
* |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | ·
* |
| EGR/VVT Monitor Result | EGR/VVT monitor | Compl or Incmpl | - | ·
* |
| A/F (O2) Sensor Heater Monitor | A/F (O2) sensor heater monitor | Not Avl or Avail | - | ·
* |
| A/F (O2) Sensor Monitor | A/F (O2) sensor monitor | Not Avl or Avail | - | ·
* |
| A/F (O2) Sensor Monitor Result | A/F (O2) sensor monitor | Compl or Incmpl | - | ·
* |
| Secondary Air Injection System Monitor | Secondary air injection system monitor | Not Avl or Avail | - | ·
* |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | ·
* |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | ·
* |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | ·
* |
| Catalyst Monitor Result | Catalyst monitor | Compl or Incmpl | - | ·
* |
*:
Avail: The monitor is available on this vehicle.
Not Avl: The monitor is not available on this vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the power switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or cable is disconnected from the negative (-) auxiliary battery terminal.
Various Vehicle Conditions 2 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TC Terminal | TC terminal status | ON or OFF | - | Active Test [Activate the TC Terminal] support data. |
| MIL | MIL status | ON or OFF | OFF | - |
| MIL ON Run Distance | Distance driven with MIL on | Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | - | This is the distance driven since the MIL was illuminated. |
| Running Time from MIL ON | Running time from MIL on | Min.: 0 min, Max.: 65535 min | Running time after MIL turned on | - |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 min, Max.: 65535 min | Time after DTCs cleared | - |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | Distance driven after DTCs cleared | This is the distance driven since DTCs were cleared (or since the vehicle left the factory). |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0, Max.: 255 | - | This is the number of warmup cycles after the DTCs were cleared. |
| Distance Traveled from Last Battery Cable Disconnect | Distance driven after auxiliary battery cable disconnected | Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | Total distance vehicle driven after auxiliary battery cable disconnected | - |
| IG OFF Elapsed Time | Time after power switch off | Min.: 0 min, Max.: 655350 min | Cumulative time after power switch off | - |
| OBD Requirements | OBD requirement | - | - | - |
| Number of Emission DTC | Emissions-related DTCs | Min.: 0, Max.: 127 | - | This is the number of emissions-related DTCs stored. |
Misfire (Ptrl Misfire)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Ignition Trigger Count | Ignition counter | Min.: 0, Max.: 65535 | 0 to 400 | ·
This is the cumulative number of ignitions. ·
This counter is increased by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions. ·
The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by the value of this item. ·
The misfire rate for each cylinder = Misfire Count Cylinder #1 to #4 / Ignition Trigger Count
|
| Misfire Count Cylinder #1 | Misfire count of No. 1 cylinder | Min.: 0, Max.: 255 | 0 | ·
This is the misfire count for No. 1 cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #2 | Misfire count of No. 2 cylinder | Min.: 0, Max.: 255 | 0 | ·
This is the misfire count for No. 2 cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #3 | Misfire count of No. 3 cylinder | Min.: 0, Max.: 255 | 0 | ·
This is the misfire count for No. 3 cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| Misfire Count Cylinder #4 | Misfire count of No. 4 cylinder | Min.: 0, Max.: 255 | 0 | ·
This is the misfire count for No. 4 cylinder. ·
This counter is increased by one for each misfire and is cleared every 200 revolutions. ·
Check this item to help determine the malfunctioning cylinder. |
| All Cylinders Misfire Count | Misfire count of all cylinders | Min.: 0, Max.: 255 | 0 | ·
This is the total misfire count of all cylinders. ·
This counter is increased by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions. |
| Misfire RPM | Engine speed for first misfire range | Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: 0 misfires | ·
This is the average engine speed recorded when misfiring occurs. ·
The value of this item is closer to the actual conditions of the vehicle at the time misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference. |
| Misfire Load | Engine load for first misfire range | Min.: 0%., Max.: 510% | 0%: 0 misfires | ·
This is the average engine load recorded when misfiring occurs. ·
The value of this item is closer to the actual conditions of the vehicle at the time misfire occurred than the values of Engine Speed and Engine Load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference. |
| Misfire Margin | Misfire monitoring | Min.: -128%, Max.: 127% | 0 to 127%: Idling with warmed up engine (inspection mode [maintenance mode]) | ·
This is the misfire detection margin. ·
Misfire Margin = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100% ·
When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. This item is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring. ·
A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring. ·
Example: When the engine is determined to be misfiring, Misfire Margin = -128 to 0%. |
| Catalyst OT Misfire Fuel Cut | Fuel cut to prevent catalyst from overheating during misfire | Not Avl or Avail | Not Avl | ·
When a high frequency of misfires is concentrated in a certain cylinder, this function stops fuel injection for that cylinder. ·
For vehicles which support this function, stop this fuel cut using the Active Test and confirm the misfire counts to determine the malfunctioning cylinder. ·
Avail: "Fuel cut to prevent catalyst from overheating during misfire" available ·
Not Avl: "Fuel cut to prevent catalyst from overheating during misfire" not available |
| Catalyst OT Misfire Fuel Cut History | History of fuel cut to prevent catalyst from overheating during misfire | ON or OFF | OFF | This can be used to tell whether there was a large amount of misfires occurred at a certain cylinder. |
| Catalyst OT Misfire Fuel Cut Cylinder #1 | Fuel cut operation of No. 1 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #2 | Fuel cut operation of No. 2 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #3 | Fuel cut operation of No. 3 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
| Catalyst OT Misfire Fuel Cut Cylinder #4 | Fuel cut operation of No. 4 cylinder (if certain level of misfire malfunction is detected) | ON or OFF | OFF | - |
Various Vehicle Conditions 3 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Start Hesitation | History of hesitation during engine start | ON or OFF | - | This item changes to ON when the engine speed does not reach 500 rpm during cranking. |
| Low Revolution for Engine Start | History of low engine speed after engine start | ON or OFF | - | This item changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of the engine was starting. |
| Engine Cooling Fan | Engine cooling fan operation status | OFF, Low or High | - | - |
| Electric Water Pump | Electric water pump speed status | Min.: 0 rpm, Max.: 10200 rpm | - | - |
| Coolant Water Route Switching Valve | Flow shutting valve (water valve) operating state | Open or Close | - | Active Test [Activate the Coolant Water Route Switching Valve] support data. |
Compression (Compression)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed Cylinder #1 | Engine speed for No. 1 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - | ·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. ·
This is the engine speed of No. 1 cylinder measured during fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #2 | Engine speed for No. 2 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - | ·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. ·
This is the engine speed of No. 2 cylinder measured during fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #3 | Engine speed for No. 3 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - | ·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. ·
This is the engine speed of No. 3 cylinder measured during fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Engine Speed Cylinder #4 | Engine speed for No. 4 cylinder | Min.: 0 rpm, Max.: 51199 rpm | - | ·
Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. ·
This is the engine speed of No. 4 cylinder measured during fuel-cut with the engine cranking. ·
When there is compression loss, the engine speed of the malfunctioning cylinder increases.
|
| Average Engine Speed of All Cylinder | Average engine speed for all cylinders | Min.: 0 rpm, Max.: 51199 rpm | - | Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. |
Various Vehicle Conditions 4 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Requested Engine Torque | Requested engine torque | Min.: 0 kW, Max.: 16383.75 kW | 0 to 72 kW | - |
| HV Target Engine Speed | HV target engine speed | Min.: 0 rpm, Max.: 6375 rpm | 0 to 5200 rpm | - |
| Actual Engine Torque | Actual engine torque | Min.: -32768 Nm, Max.: 32767 Nm | 0 Nm: Idling (inspection mode [maintenance mode], not charge control) | - |
| Engine Driving Time | Engine driving time | Min.: 0 sec, Max.: 255 sec | 0 to 255 sec | - |
| Request Engine Run Time | Request engine run time | Min.: 0 sec, Max.: 25.5 sec | 0 to 25.5 sec | - |
| Judge Time Engine Ignition | Judgment time for complete explosion of ignition | Min.: 0 sec, Max.: 25.5 sec | 0 to 25.5 sec | - |
| Judge Time Engine Output | Judgment time for time until engine output | Min.: 0 sec, Max.: 25.5 sec | 0 to 25.5 sec | - |
| Fuel Level | Fuel level | Empty or Not Emp | Not Emp | - |
| ISC Learning Value | ISC learning value | Min.: -1024 Nm, Max.: 1023.96 Nm | -5 to 10 Nm: Idling with warmed up engine (inspection mode [maintenance mode]) | - |
| ISC Learning | ISC learning | Compl or Incmpl | ·
Compl: ISC learned value complete ·
Incmpl: ISC learned value incomplete |
- |
| F/C for Engine Stop Req | Fuel cut for engine stop request | ON or OFF | ON → OFF:
Engine stopped → Engine start |
- |
| Engine Independent | Engine independent operation | Not Opr or Operate | ·
Operate: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) ·
Not Opr: Idling with warmed up engine (inspection mode [maintenance mode]), accelerator pedal depressed |
"Not Opr" is displayed during charge control. |
| Racing Operation | Racing operation | Not Opr or Operate | ·
Operate: Idling with warmed up engine (inspection mode [maintenance mode]), accelerator pedal depressed ·
Not Opr: Idling with warmed up engine (inspection mode [maintenance mode], not charge control) |
- |
| Request Warm-up | Request engine warm up | Not Req or Request | - | - |
| Engine Independent Control | Engine independent control operation | Not Opr or Operate | - | - |
| Electric Water Pump Target Speed | Engine water pump assembly target speed | Min.: 0 rpm, Max.: 6375 rpm | - | Target motor speed of the engine water pump. |
| Electric Water Pump Speed | Engine water pump assembly speed | Min.: 0 rpm, Max.: 6375 rpm | - | Actual motor speed of the engine water pump. |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Warm up the engine.
Turn the power switch off.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Injection Volume | Control the injection volume | Between -12.5% and 24.8% | ·
All fuel injector assemblies are tested at the same time. ·
Injection volume can be changed in fine gradations within the control range. ·
This Active Test enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs. ·
To perform this Active Test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2. ·
While performing the Active Test, air fuel ratio feedback control and feedback learning are stopped. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). |
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% | ·
All fuel injector assemblies are tested at the same time. ·
This Active Test enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs. ·
To perform this Active Test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2. ·
While performing the Active Test, air fuel ratio feedback control and feedback learning are stopped. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). ·
See waveform *2. |
| Activate the EVAP Purge VSV | Activate purge VSV control | ON/OFF | ·
Confirm that the vehicle is stopped. ·
The purge VSV is opened with approximately 50% duty ratio. ·
See waveform *4. |
| Activate the Circuit Relay | Activate fuel pump | ON/OFF | Perform this test when the following conditions are met:
·
Power switch is on (IG). ·
Engine is stopped. ·
Park (P) has been selected. |
| Activate the TC Terminal | Turn on and off TC and TE1 (CG) connection | ON/OFF | ·
Confirm that the vehicle is stopped. ·
ON: TC and TE1 (CG) are connected. ·
OFF: TC and TE1 (CG) are disconnected. |
| Prohibit the Idle Fuel Cut | Prohibit idling fuel cut control | Start/Stop | Perform this test when the following conditions are met:
·
Power switch is on (IG). ·
Park (P) has been selected. |
| Prohibit the Catalyst OT Misfire Prevent Fuel Cut | Prohibit catalyst overheat protection fuel cut | Start/Stop
Start: Fuel cut prohibited |
Perform this test when the vehicle is stopped and the engine speed is 3000 rpm or less. |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | ·
Close/Open ·
Start/Stop Open: Throttle valve opens slowly |
Perform this test when the following conditions are met:
·
Power switch is on (IG). ·
Engine is stopped. ·
Accelerator pedal is fully depressed (accelerator pedal position: 58 degrees or more). ·
Park (P) has been selected. |
| Control the ETCS Open/Close Fast Speed | Throttle actuator | ·
Close/Open ·
Start/Stop Open: Throttle valve opens quickly |
·
Same as above. ·
See waveform *3. |
| Control the Intake VVT OCV Duty Ratio Bank 1 | Control camshaft timing oil control valve assembly | -100 to 100% (This value added to present camshaft timing oil control valve assembly control duty)
100%: Maximum advance -100%: Maximum retard |
·
Engine stalls or idles roughly when the camshaft timing oil control valve assembly is set to 100%. ·
Perform this test when the following conditions are met: -
Engine is idling. ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). ·
See waveform *6. |
| Control the EGR Step Position | Control EGR valve assembly | From 0 to 110 step | ·
The EGR valve is fully closed at step position 0, and fully open at step position 110. ·
The amount of EGR gas flowing into the intake manifold varies in accordance with the EGR valve opening angle. ·
Perform this test when the following conditions are met: -
Engine is running. -
Park (P) has been selected. ·
Do not leave the EGR valve open for 10 seconds or more while performing the Active Test. ·
Be sure to return the EGR valve to step 0 when the Active Test is completed. ·
Do not open the EGR valve 30 steps or more while performing the Active Test. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). ·
See waveform *5. |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | ·
#1/#2/#3/#4 ·
Start/Stop |
·
Perform this test when the following conditions are met: -
Engine is idling. -
Park (P) has been selected. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). |
| Control the All Cylinders Fuel Cut | Fuel cut for all cylinders | Start/Stop | ·
Perform this test when the following conditions are met: -
Engine is idling. -
Park (P) has been selected. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). |
| Check the Cylinder Compression | Check the cylinder compression pressure | Start/Stop | ·
Fuel injection and ignition stop of all cylinders. ·
This Active Test should be performed with the engine in Inspection Mode (Maintenance Mode). *1 |
| Control the Engine Cooling Fan | Control electric cooling fan motor | OFF/Low/High | Perform this test when vehicle is stopped. |
| Activate the Electric Water Pump | Engine water pump assembly speed control | 0 rpm/3000 rpm | Perform this test when engine coolant temperature less than 100°C (212°F). |
| Activate the Coolant Water Route Switching Valve | Operate flow shutting valve (water valve) | Close/Open | Perform this test when engine coolant temperature less than 100°C (212°F). |
Use a fully-charged HV battery.
While the Check the Cylinder Compression Active Test is being performed, if the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine and warm it up.
Turn the power switch off.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Do not start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.
To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
Push the snapshot button to turn the snapshot function on.
Using the snapshot function, data can be recorded while performing the Active Test.
While the engine is not running, press the Active Test button to change Check the Cylinder Compression to "Start".
After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.
Crank the engine.
Continue to crank the engine until the values change from the default value (51199 rpm).
Monitor the engine speed (Engine Speed Cylinder #1 to #4) displayed on the GTS.
If the Check the Cylinder Compression Active Test needs to be performed after it is changed to "Start" and performed once, press the Exit button to return to the Active Test menu screen. Then perform the Check the Cylinder Compression Active Test again.
As soon as the measurements are obtained, stop the Active Test.
At first, the GTS display will show each cylinder's engine speed measurement to be extremely high. After the engine has started, each cylinder's engine speed measurement will change to the actual engine speed.
If the cylinder engine speed values (Engine Speed Cylinder #1 to #4) displayed in the Data List do not change from an extremely high value, return to the Active Test menu screen, change "Check the Cylinder Compression" to "Start" and crank the engine again within 1 second.
Stop the engine and change the Active Test "Check the Cylinder Compression" to "Stop" after the engine stops.
When performing the Active Test, DTC P160400 (startability malfunction) may be stored.
After performing the Active Test, make sure to check and clear the DTCs.
Push the snapshot button to turn the snapshot function off.
Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
If the data is not displayed as a graph, the change of the values cannot be observed.
Check the change in engine speed values.
*2: Control the Injection Volume for A/F Sensor (Engine warmed up and idling, inspection mode [maintenance mode], not charge control)
| GTS Display | Measurement Item/Operation | Normal Condition | |
|---|---|---|---|
| Control the Injection Volume for A/F Sensor | - | ▲A | ▲B |
| Active Test operation | -12.5% | 12.5% | |
| A/F (O2) Sensor Voltage B1S1 | 3.724 V | 2.397 V | |
| O2 Sensor Voltage B1S2 | 0.055 V | 0.955 V | |
While performing the Active Test, air fuel ratio feedback control and feedback learning are stopped.
Usually, the value of A/F (O2) Sensor Voltage B1S1 drops below 3.1 V when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.
Usually, the value of A/F (O2) Sensor Voltage B1S1 changes to 3.4 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
Usually, the value of O2 Sensor Voltage B1S2 changes to 0.55 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to 12.5%.
Usually, the value of O2 Sensor Voltage B1S2 drops below 0.4 V when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
*3: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Power switch on (IG), Accelerator pedal fully depressed)
| GTS Display | Measurement Item/Operation | Normal Condition | |
|---|---|---|---|
| Control the ETCS Open/Close Fast Speed | - | ▲A | ▲B |
| Active Test operation | Open | Close | |
| Throttle Position Sensor No.1 Voltage | 2.597 V | 0.742 V | |
| Throttle Motor Duty Ratio (Open) | 13.0% | 0.0% | |
| Throttle Motor Duty Ratio (Close) | 0.0% | 13.0% | |
If any DTCs related to the Electronic Throttle Control System (ETCS) are stored, this Active Test cannot be performed.
*4: Activate the EVAP Purge VSV (Engine warmed up and idling, inspection mode [maintenance mode], not charge control)
| GTS Display | Measurement Item/Operation | Normal Condition | |
|---|---|---|---|
| Activate the EVAP Purge VSV | - | ▲A | ▲B |
| Active Test operation | ON | OFF | |
| EVAP (Purge) VSV | 49.8% | 0.0% | |
| Injector Cylinder #1 (Port) | 1859 μs | 1894 μs | |
| A/F (O2) Sensor Voltage B1S1 | 3.296 V | 3.301 V | |
The graphs and values above are for reference only because the fuel injection volume (compensation volume) varies depending on the HC density of the purge air from the canister.
Even when the Active Test is performed (the purge VSV is opened approximately 50%), the ECM performs air fuel ratio feedback to maintain the air fuel ratio at the stoichiometric ratio. Therefore, by observing the change in the Data List item "Injector Cylinder #1 (Port)", it is possible to determine whether the purge VSV is actually open.
*5: Control the EGR Step Position (Engine warmed up and idling, inspection mode [maintenance mode], not charge control)
| GTS Display | Measurement Item/Operation | Normal Condition | |||
|---|---|---|---|---|---|
| Control the EGR Step Position | - | ▲A | ▲B | ▲C | ▲D |
| EGR Step Position | 0 step | 10 step | 20 step | 30 step | |
| Intake Manifold Absolute Pressure | 28 kPa (4.06 psi) | 28 kPa (4.06 psi) | 67 kPa (9.72 psi) | 88 kPa (12.76 psi) | |
Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more while performing Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
When the value of Control the EGR Step Position is "0 step", the value of Intake Manifold Absolute Pressure should be between 20 and 40 kPa (2.9 to 5.8 psi).
When the EGR system is normal and the value of Control the EGR Step Position is changed from "0 step" to "30 step", the value of Intake Manifold Absolute Pressure will increase to a value at least 10 kPa (1.45 psi) higher than the value of Intake Manifold Absolute Pressure when the value of Control the EGR Step Position was "0 step".
If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).
*6: Control the Intake VVT OCV Duty Ratio Bank 1 (Idling, inspection mode [maintenance mode], not charge control)
| GTS Display | Measurement Item/Operation | Normal Condition | |
|---|---|---|---|
| Control the Intake VVT OCV Duty Ratio Bank 1 | - | ▲A | ▲B |
| Active Test operation* | 30% | -30% | |
| Intake VVT Change Angle Bank 1 | 62.5 DegFR | 0.0 DegFR | |
| Intake VVT OCV Control Duty Ratio Bank 1 | 65.4% | 25.7% | |
| Intake VVT Hold Learn Value Bank 1 | 50.0% | 50.0% | |
*: Change the control value for Control the Intake VVT OCV Duty Ratio Bank 1 to 30% or -30%.
Test not possible with park (P) selected during charge control. Select neutral (N) to perform test.