These DTCs indicate malfunctions relating to the primary circuit.
If DTC P035113 is output, check the Ignition Coil Assembly (No. 1 Cylinder) circuit.
If DTC P035213 is output, check the Ignition Coil Assembly (No. 2 Cylinder) circuit.
If DTC P035313 is output, check the Ignition Coil Assembly (No. 3 Cylinder) circuit.
If DTC P035413 is output, check the Ignition Coil Assembly (No. 4 Cylinder) circuit.
A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P035113 | Ignition Coil "A" Circuit Open | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM ·
Ignition Coil Assembly (No. 1 Cylinder) ·
ECM |
Comes on | DTC stored | SAE Code: P0351 |
| P035213 | Ignition Coil "B" Circuit Open | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM ·
Ignition Coil Assembly (No. 2 Cylinder) ·
ECM |
Comes on | DTC stored | SAE Code: P0352 |
| P035313 | Ignition Coil "C" Circuit Open | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM ·
Ignition Coil Assembly (No. 3 Cylinder) ·
ECM |
Comes on | DTC stored | SAE Code: P0353 |
| P035413 | Ignition Coil "D" Circuit Open | No IGF signal to the ECM while the engine is running (1 trip detection logic). | ·
Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM ·
Ignition Coil Assembly (No. 4 Cylinder) ·
ECM |
Comes on | DTC stored | SAE Code: P0354 |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
With the engine idling, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
| ECM Terminal Name | CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a malfunction of an igniter and stores a DTC.
| Required Sensors/Components (Main) | Igniter |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine.
Idle the engine for 10 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P035113, P035213, P035313 or P035413.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following procedure.
Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
- for Lithium-ion Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
- for Nickel Metal Hydride Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY
- for Lithium-ion Battery: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>VEHICLE CONTROL HISTORY
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).
Do not change the location of the connectors.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Same DTC output | A |
| Different ignition coil DTC output | B |
Perform "Inspection After Repair" after replacing the ignition coil assembly.
Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
Disconnect the ignition coil assembly connectors.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C21-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| C22-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| C23-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| C24-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C21, C22, C23 and C24 ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C21-4 (GND) - Body ground | Always | Below 1 Ω |
| C22-4 (GND) - Body ground | Always | Below 1 Ω |
| C23-4 (GND) - Body ground | Always | Below 1 Ω |
| C24-4 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C21, C22, C23 and C24 ignition coil assembly connectors.
Disconnect the C63 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C21-2 (IGF) - C63-71 (IGF1) | Always | Below 1 Ω |
| C22-2 (IGF) - C63-71 (IGF1) | Always | Below 1 Ω |
| C23-2 (IGF) - C63-71 (IGF1) | Always | Below 1 Ω |
| C24-2 (IGF) - C63-71 (IGF1) | Always | Below 1 Ω |
| C21-3 (IGT1) - C63-75 (IGT1) | Always | Below 1 Ω |
| C22-3 (IGT2) - C63-74 (IGT2) | Always | Below 1 Ω |
| C23-3 (IGT3) - C63-73 (IGT3) | Always | Below 1 Ω |
| C24-3 (IGT4) - C63-72 (IGT4) | Always | Below 1 Ω |
| C21-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C22-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C23-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C24-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C21-3 (IGT1) or C63-75 (IGT1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C22-3 (IGT2) or C63-74 (IGT2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C23-3 (IGT3) or C63-73 (IGT3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C24-3 (IGT4) or C63-72 (IGT4) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG