Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404405 SFI SYSTEM C

M20A-FXS ENGINE CONTROL  SFI SYSTEM  P001700  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B  


DESCRIPTION

Refer to DTC P001313.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>P001313

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001700 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal
(2 trip detection logic).
·

Valve timing

·

Cam timing oil control solenoid assembly

·

Camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly)

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on DTC stored SAE Code: P0017

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1800 rpm

CONFIRMATION DRIVING PATTERN

A409115E02
4.302,1.115 4.156,0.479 4.156,0.479 4.01,0.479 false 0.208,0.49 2.198,0.688 1.99,0.198 10 false Vehicle Speed 0.792,1.771 2.781,1.969 1.99,0.198 10 false Idling 0.281,2.031 1.135,2.5 0.854,0.469 10 false Power Switch on (IG) 1.906,2.583 2.667,2.958 0.76,0.375 10 false Warming up 2.74,2.573 3.927,2.875 1.188,0.302 10 false 5 minutes or more 3.823,3.031 5.01,3.333 1.188,0.302 10 false [D] 1.542,2.167 2.729,2.469 1.188,0.302 10 false [A] 2.208,1.656 3.396,1.958 1.188,0.302 10 false [B] 3.198,1.656 4.385,1.958 1.188,0.302 10 false [C] 4.469,0.875 5.656,1.177 1.188,0.302 10 false [E] 5.76,1.656 6.948,1.958 1.188,0.302 10 false [F] 6.365,3.01 6.708,3.313 0.344,0.302 10 false [G] 3.938,2.594 5.125,2.896 1.188,0.302 10 false 10 minutes or more 5.25,2.604 6.438,2.906 1.188,0.302 10 false 5 minutes or more 1.688,0.396 4.063,0.802 2.375,0.406 10 false There is no designated vehicle speed 1.698,0.573 4.073,0.979 2.375,0.406 10 false [Engine running]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG) [A].

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

10.

Idle the engine for 5 minutes or more [C].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P001700.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [E] through [G].



16.

With the engine running, drive the vehicle for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


17.

Idle the engine for 5 minutes or more [F].

18.

Enter the following menus: Powertrain / Engine / Trouble Codes [G].

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Check the DTC judgment result.

HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

The monitor for this DTC detects when the timing chain is shifted by two teeth or more.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001700)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001700 is output A
DTC P001700 and other DTCs are output B


HINT:

If any DTCs other than P001700 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1 / Data List / Exhaust VVT Change Angle Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
Data List Display
Exhaust VVT Change Angle Bank 1
50004 372 5 398

g.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.


HINT:
·

Test not possible with the shift lever in P during charge control. Move the shift lever to N to perform test.

·

If the DTCs are stored after the Active Test, clear the DTCs.




Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
a.

Inspect the cam timing oil control solenoid assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL SOLENOID>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
a.

Inspect the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

6.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P001700)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001700 is output B




A

B