Home › Engine / Hybrid System › M20A-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083960 M20A-FXS ENGINE CONTROL _0404405 SFI SYSTEM C

M20A-FXS ENGINE CONTROL  SFI SYSTEM  P019515  Engine Oil Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P019511.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>P019511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P019515 Engine Oil Temperature Sensor Circuit Short to Battery or Open The engine oil pressure and temperature sensor output voltage is higher than 4.865 V for 5 seconds or more (1 trip detection logic).
·

Open or short in engine oil temperature sensor circuit

·

Engine oil pressure and temperature sensor

·

ECM


Does not come on DTC stored SAE Code: P0198

HINT:

When a DTC is output, check the Data List item "Engine Oil Temperature Sensor" using the GTS.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

DTC No. Engine Oil Temperature Sensor Malfunction
P019515 -40°C (-40°F)
·

Short to +B in THEO circuit

·

Open in THEO circuit

·

Open in ETHE circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the engine oil pressure and temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil pressure and temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil pressure and temperature sensor circuit is malfunctioning and stores this DTC.

Example:

If the engine oil pressure and temperature sensor output voltage is higher than 4.865 V for 5 seconds or more, the ECM will store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P019515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A452295C03
0.302,1.052 0.656,1.302 0.354,0.25 2.031,1.115 2.583,1.781 true 1.063,1.75 1.573,1.208 true 1.833,1.771 1.802,1.208 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.344,1.094 0.656,1.292 0.313,0.198 10 false C88 2.49,1.823 2.948,2.042 0.458,0.219 10 false TOUT 0.906,1.802 1.281,2.042 0.375,0.24 10 false GND 1.76,1.823 2.073,2.021 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Engine Oil Pressure and Temperature Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the engine oil pressure and temperature sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C88-3 (VC) - C88-2 (GND) Power Switch on (IG) 4.5 to 5.5 V
C88-4 (TOUT) - C88-2 (GND) Power Switch on (IG) 3.0 to 5.5 V



d.

Turn the power switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C88-2 (GND) - Body ground Power Switch off Below 1 Ω
C88-3 (VC) - C88-4 (TOUT) Power Switch off 171 to 189 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR - ECM)
a.

Disconnect the C88 engine oil pressure and temperature sensor connector.


b.

Disconnect the C97 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C88-2 (GND) - C97-100 (EPEO) Always Below 1 Ω
C88-4 (TOUT) - C97-123 (THEO) Always Below 1 Ω
C88-4 (TOUT) or C97-123 (THEO) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR