Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) J

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  Inverter Low-voltage Circuit  


DESCRIPTION

The cause of the malfunction may be the low-voltage circuit.

Check whether there is an open circuit in the inverter +B low-voltage power source system or a problem in the communication between the hybrid vehicle control ECU and inverter.

Related Parts Check
Area Inspection
Inverter +B low-voltage power source system check Check for inverter overcurrent malfunction.
Communication malfunction between hybrid vehicle control ECU and MG-ECU inside inverter with converter assembly Check for inverter overcurrent malfunction due to communication malfunction.
Check for short to ground in inverter +B low-voltage power source system -

WIRING DIAGRAM

A445684E10
3.552,2.875 4.76,3.219 1.208,0.344 10 false from IGCT Relay 4.125,2.271 4.75,2.594 0.625,0.323 10 false PCU FR 6.188,2.521 6.677,2.823 0.49,0.302 10 false GND2 6.177,2.094 6.667,2.396 0.49,0.302 10 false GND1 5.125,2.104 5.458,2.396 0.333,0.292 10 false +B 5.115,2.552 5.448,2.844 0.333,0.292 10 false +B2 5.104,0.542 5.594,0.844 0.49,0.302 10 false HMCL 1.531,0.563 2.021,0.865 0.49,0.302 10 false HMCL 1.542,1.042 2.031,1.344 0.49,0.302 10 false HMCH 5.094,1.031 5.583,1.333 0.49,0.302 10 false HMCH 4.99,3.24 7.156,3.615 2.167,0.375 10 false Inverter with Converter Assembly 6.646,2.427 7.135,2.729 0.49,0.302 10 false 23 2.042,0.646 2.531,0.948 0.49,0.302 10 false A48 4.927,2.448 5.417,2.75 0.49,0.302 10 false 5 6.646,2 7.135,2.302 0.49,0.302 10 false 24 4.917,2 5.406,2.302 0.49,0.302 10 false 6 4.135,2 4.448,2.292 0.313,0.292 10 false 1 4.552,2.01 4.865,2.302 0.313,0.292 10 false 2 4.865,0.573 5.354,0.875 0.49,0.302 10 false 19 4.875,1.052 5.365,1.354 0.49,0.302 10 false 20 4.969,3.042 5.458,3.344 0.49,0.302 10 false C65 2.052,1.125 2.542,1.427 0.49,0.302 10 false A48 2.052,1.604 2.542,1.906 0.49,0.302 10 false A48 2.094,2.094 2.583,2.396 0.49,0.302 10 false F2 2.094,2.615 2.583,2.917 0.49,0.302 10 false F3 2.094,0.438 2.583,0.74 0.49,0.302 10 false 30 2.094,0.927 2.583,1.229 0.49,0.302 10 false 31 2.094,1.406 2.583,1.708 0.49,0.302 10 false 29 4.875,1.49 5.365,1.792 0.49,0.302 10 false 13 5.125,1.583 5.885,1.885 0.76,0.302 10 false DRN1 1.583,1.615 2.344,1.917 0.76,0.302 10 false DRN5 0.208,3 2.719,3.406 2.51,0.406 10 false Hybrid Vehicle Control ECU 1.76,2.094 2.25,2.396 0.49,0.302 10 false E1 1.677,2.604 2.167,2.906 0.49,0.302 10 false E12 2.115,2.406 2.417,2.677 0.302,0.271 10 false 4 2.125,1.885 2.427,2.156 0.302,0.271 10 false 6 5.865,0.906 6.125,1.177 0.26,0.271 10 false * 1,0.938 1.26,1.208 0.26,0.271 10 false * 0.323,3.469 2.094,3.792 1.771,0.323 10 false *: Approximately 120 Ω 3.281,0.563 3.594,0.76 0.313,0.198 10 false 9 3.781,0.563 4.094,0.76 0.313,0.198 10 false 9 3.219,1.052 3.469,1.229 0.25,0.177 10 false 10 3.771,1.052 4.094,1.24 0.323,0.188 10 false 10 3.24,1.354 3.552,1.552 0.313,0.198 10 false 11 3.771,1.365 4.083,1.563 0.313,0.198 10 false 11 3.458,1.594 3.917,1.792 0.458,0.198 10 false CA5

CAUTION / NOTICE / HINT

This step is referenced from the procedures for each DTC.

If the inspection results below are normal, perform the next procedure for the referenced DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


PROCEDURE

1.CHECK FUSE (PCU FR)
a.
A389522C01
2.667,1.917 1.75,1.531 true 0.354,0.094 0.667,0.25 0.313,0.156 10 false *1 2.74,1.896 3.052,2.052 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 PCU FR Fuse


Remove the PCU FR fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PCU FR fuse terminal Always Below 1 Ω



c.

Install the PCU FR fuse.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FR FUSE)
2.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the inverter with converter assembly connector.


c.
A365593C08
0.292,0.885 0.667,1.146 0.375,0.26 2.042,0.917 2.604,0.302 true 1.906,0.906 1.646,0.146 true 2.031,1.25 2.719,1.833 true 1.906,1.25 1.917,1.833 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.354,0.948 0.813,1.146 0.458,0.198 10 false C65 2.656,0.156 2.969,0.354 0.313,0.198 10 false +B 1.344,0.01 1.802,0.208 0.458,0.198 10 false +B2 2.563,1.865 3.021,2.063 0.458,0.198 10 false GND1 1.823,1.865 2.438,2.063 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-24 (GND1) - Body ground Power switch off Below 1 Ω
C65-23 (GND2) - Body ground Power switch off Below 1 Ω



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C65-6 (+B) - Body ground Power switch on (IG) Same as auxiliary battery voltage
C65-5 (+B2) - Body ground Power switch on (IG) Same as auxiliary battery voltage


NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


i.

Reconnect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the inverter with converter assembly connector.


c.

Disconnect the hybrid vehicle control ECU connector.


d.
A389523C01
0.333,0.833 0.833,1.083 0.5,0.25 1.177,2.271 1.677,2.521 0.5,0.25 0.833,1.667 1.375,1.396 true 2,4.417 1.604,4.198 true 1.531,4.208 1.083,4.417 true 2,2 1.542,1.396 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.188,2.167 0.5,2.323 0.313,0.156 10 false *b 0.531,1.688 1.094,1.844 0.563,0.156 10 false HMCL 1.844,2.031 2.406,2.188 0.563,0.156 10 false HMCH 0.792,4.448 1.354,4.604 0.563,0.156 10 false HMCH 1.906,4.438 2.469,4.594 0.563,0.156 10 false HMCL 0.458,0.865 0.76,1.052 0.302,0.188 10 false C65 1.302,2.302 1.604,2.49 0.302,0.188 10 false A48
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C65-20 (HMCH) - A48-31 (HMCH) Power switch off Below 1 Ω
C65-19 (HMCL) - A48-30 (HMCL) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C65-20 (HMCH) or A48-31 (HMCH) - Body ground and other terminals Power switch off 10 kΩ or higher
C65-19 (HMCL) or A48-30 (HMCL) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C65-20 (HMCH) or A48-31 (HMCH) - Body ground and other terminals Power switch on (IG) Below 1 V
C65-19 (HMCL) or A48-30 (HMCL) - Body ground and other terminals Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU and inverter with converter assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 2 minutes or more.


j.

Reconnect the hybrid vehicle control ECU connector.


k.

Reconnect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A394814C01
1.167,0.667 1.583,0.917 0.417,0.25 1.25,2.25 1.521,1.635 true 1.833,2.25 1.573,1.635 true 1.25,0.708 1.708,0.906 0.458,0.198 10 false A48 0.802,2.208 1.417,2.406 0.615,0.198 10 false HMCH 1.896,2.188 2.51,2.385 0.615,0.198 10 false HMCL 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a
*a Component without harness connected
(Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-31 (HMCH) - A48-30 (HMCL) Power switch off 80 to 170 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

INVERTER LOW-VOLTAGE CIRCUIT NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

NG

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FR FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the inverter with converter assembly connector.


c.
A365593C09
0.292,0.979 0.667,1.229 0.375,0.25 2.031,0.906 2.708,0.333 true 1.917,0.896 1.656,0.125 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.354,1.031 0.813,1.229 0.458,0.198 10 false C65 2.75,0.208 3.063,0.406 0.313,0.198 10 false +B 1.354,0.021 1.813,0.219 0.458,0.198 10 false +B2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C65-6 (+B) - Body ground Power switch off 10 kΩ or higher
C65-5 (+B2) - Body ground Power switch off 10 kΩ or higher



d.

Reconnect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NEXT

REPLACE FUSE (PCU FR)

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PCU FR)