Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) D

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  UTILITY  


ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs even if no DTCs are stored.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Turn the power switch off and wait for 2 minutes or more.


f.

Turn the power switch on (IG).


g.

Perform the DTC judgment driving pattern to run the DTC judgment.


h.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

Powertrain > Hybrid Control > Utility
Tester Display
All Readiness
50005 397 1020

i.

Input the DTC to be confirmed.


j.

Check the DTC judgment result.

GTS Display Description

If the judgment result shows Incomplete or N/A, perform the DTC confirmation driving pattern again.

Normal
·

DTC judgment completed

·

System normal


Abnormal
·

DTC judgment completed

·

System abnormal


Incomplete
·

DTC judgment not completed

·

Perform the driving pattern


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

·

Perform the driving pattern




k.

Turn the power switch off.



DIAGNOSIS RELATED INFORMATION


a.

Check for diagnosis related information.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Hybrid Control / Utility / Diagnosis Related Information.

Powertrain > Hybrid Control > Utility
Tester Display
Diagnosis Related Information
50005 397 1056

v.

Check the Diagnosis Related Information, and then write them down.



b.

Clear diagnosis related information.

NOTICE:

Clearing the DTCs will also clear the diagnosis related information.


i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


v.

Clear the diagnosis related information and freeze frame data.


vi.

Turn the power switch off.




BATTERY STATUS INFO UPDATE


HINT:

If the HV battery has been replaced, make sure to perform "Battery Status Info Update".

It is necessary to update the HV battery status information stored in the hybrid vehicle control ECU, and turn lamp off on the combination meter after the HV battery replacement.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Utility / Battery Status Info Update.

Powertrain > Hybrid Control > Utility
Tester Display
Battery Status Info Update
50005 397 5224

e.

Turn the power switch off.



HIGH VOLTAGE FUSE ACCUMULATED LOAD HISTORY RESET


HINT:
·

If the hybrid battery terminal block has been replaced, make sure to perform "High Voltage Fuse Accumulated Load History Reset" and then clear the DTCs.

·

When "High Voltage Fuse Accumulated Load History Reset" is performed, the high voltage fuse accumulated load history stored in the hybrid vehicle control ECU will be initialized.

·

If "High Voltage Fuse Accumulated Load History Reset" is not performed after replacing the hybrid battery terminal block when troubleshooting DTC P0A9563, the same DTC will be output again.



a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Utility / High Voltage Fuse Accumulated Load History Reset.

Powertrain > Hybrid Control > Utility
Tester Display
High Voltage Fuse Accumulated Load History Reset
50005 397 8001

e.

According to the display on the GTS, perform High Voltage Fuse Accumulated Load History Reset and check that "High Voltage Fuse Accumulated Load History Reset is complete." is displayed.

HINT:

If "High Voltage Fuse Accumulated Load History Reset has failed. Do you want to try again?" is displayed on the GTS, perform the procedure again.



f.

Turn the power switch off.