The EV drive mode signal will be sent to the hybrid vehicle control ECU when the EV drive mode switch (electric parking brake switch assembly) is operated. If the specified conditions are met, the system enters EV drive mode and the vehicle will be driven using EV drive mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the EV drive mode indicator.
Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV mode and a warning message will be displayed on the multi-information display.
Under the following conditions, the drive mode will not be able to be changed to EV mode:
The hybrid control system is extremely hot.
After the vehicle has been parked in an extremely hot environment, driven at high speeds or the vehicle is climbing a slope, etc.
The hybrid control system is extremely cold.
After the vehicle has been parked in an extremely cold environment (approximately 0°C or less) for a long period of time.
The engine is warming up.
The SOC (State of Charge) of the HV battery is low.
The HV battery SOC displayed on the hybrid system indicator display is low.
The vehicle is being driven at a speed higher than the specified value.
The vehicle speed is approximately 30 km/h or higher.
The accelerator pedal is being fully depressed or the vehicle is climbing a slope.
The defroster is on.
DTCs are stored.
Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.
| Result | Proceed to |
|---|---|
| No buzzer sounded and no message was displayed on multi-information display. | A |
| A buzzer sounded and a message was displayed on multi-information display. | B |
If a buzzer sounds and a message is displayed on the multi-information display, one or more of the EV drive mode entry conditions have not been met. Check that all of the EV drive mode entry conditions have been met before pressing the EV drive mode switch (electric parking brake switch assembly).
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / CAN Bus Check.
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. | B |
Turn the power switch off.
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / Health Check.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Data List / EV Mode, EV Mode SW.
| Tester Display |
|---|
| EV Mode |
| EV Mode SW |
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| EV Mode | EV drive mode transition availability | ON or OFF | In EV drive mode: ON |
| EV Mode SW | EV drive mode switch (electric parking brake switch assembly) condition | ON or OFF | EV drive mode switch (electric parking brake switch assembly) being pushed and held: ON
EV drive mode switch (electric parking brake switch assembly) not pushed: OFF |
| Result | Proceed to |
|---|---|
| The display changes according to the EV drive mode switch (electric parking brake switch assembly) operation. | A |
| The display does not change according to the EV drive mode switch (electric parking brake switch assembly) operation. | B |
Turn the power switch off.
A
B
Remove the EV drive mode switch (electric parking brake switch assembly).
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>COMBINATION SWITCH>REMOVAL
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(EV Drive Mode Switch (Electric Parking Brake Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F67-11 (S) - F67-8 (E) | EV drive mode switch (electric parking brake switch assembly) being pushed and held | Below 50 Ω |
| EV drive mode switch (electric parking brake switch assembly) not pushed | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F67-13 (S) - F67-8 (E) | EV drive mode switch (electric parking brake switch assembly) being pushed and held | Below 50 Ω |
| EV drive mode switch (electric parking brake switch assembly) not pushed | 10 kΩ or higher |
Install the EV drive mode switch (electric parking brake switch assembly).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the EV drive mode switch (electric parking brake switch assembly) connector.
| *a | Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F67-8 (E) - Body ground | Always | Below 1 Ω |
Reconnect the EV drive mode switch (electric parking brake switch assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
Disconnect the EV drive mode switch (electric parking brake switch assembly) connector.
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-15 (EVSW) - F67-11 (S) | Always | Below 1 Ω |
| F3-15 (EVSW) or F67-11 (S) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-15 (EVSW) - F67-13 (S) | Always | Below 1 Ω |
| F3-15 (EVSW) or F67-13 (S) - Body ground | Always | 10 kΩ or higher |
Reconnect the EV drive mode switch (electric parking brake switch assembly) connector.
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
NG