If the power switch is on (IG), the hybrid vehicle control ECU applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-4 (+B1) - Body ground | Power switch on (IG) | 11 to 14 V |
| A49-1 (+B2) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F2-6 (E1) - Body ground | Always | Below 1 Ω |
| F2-5 (E01) - Body ground | Always | Below 1 Ω |
| F3-5 (E02) - Body ground | Always | Below 1 Ω |
| F3-4 (E12) - Body ground | Always | Below 1 Ω |
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-6 (MREL) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
| *1 | No. 1 Engine Room Relay Block |
| *2 | PM-IGCT Fuse |
Remove the PM-IGCT fuse from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| PM-IGCT fuse terminals | Always | Below 1 Ω |
Install the PM-IGCT fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | IGCT-IG Fuse |
Remove the IGCT-IG fuse from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IGCT-IG fuse terminals | Always | Below 1 Ω |
Install the IGCT-IG fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | IGCT Relay |
Remove the IGCT relay from the No. 1 engine room relay block.
| *1 | IGCT Relay |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Auxiliary battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| Auxiliary battery voltage applied between terminals 1 and 2 | Below 1 Ω |
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
| *1 | No. 1 Engine Room Relay Block |
| *2 | PM-IGCT Fuse |
Remove the PM-IGCT fuse from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 1 Engine Room Relay Block | - | - |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
*b | PM-IGCT Fuse Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-4 (+B1) - 2 (PM-IGCT fuse holder) | Always | Below 1 Ω |
| A49-1 (+B2) - 2 (PM-IGCT fuse holder) | Always | Below 1 Ω |
Reconnect the hybrid vehicle control ECU connector.
Install the PM-IGCT fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | PM-IGCT Fuse |
| *3 | IGCT-IG Fuse |
| *4 | IGCT Relay |
Remove the IGCT-IG fuse, PM-IGCT fuse and IGCT relay from the No. 1 engine room relay block.
| *1 | No. 1 Engine Room Relay Block |
| *a | PM-IGCT Fuse Holder |
| *b | IGCT-IG Fuse Holder |
| *c | IGCT Relay Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGCT relay holder) - 2 (IGCT-IG fuse holder) | Always | Below 1 Ω |
| 5 (IGCT relay holder) - 1 (PM-IGCT fuse holder) | Always | Below 1 Ω |
Install the IGCT-IG fuse, PM-IGCT fuse and IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
| *1 | No. 1 Engine Room Relay Block |
| *2 | IGCT Relay |
Remove the IGCT relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 1 Engine Room Relay Block | - | - |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
*b | IGCT Relay Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-6 (MREL) - 1 (IGCT relay holder) | Always | Below 1 Ω |
| A48-6 (MREL) or 1 (IGCT relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
Install the IGCT relay.
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | IGCT Relay |
Remove the IGCT relay from the No. 1 engine room relay block.
| *1 | No. 1 Engine Room Relay Block |
| *a | IGCT Relay Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (IGCT relay holder) - Body ground | Always | Below 1 Ω |
Install the IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | PM-IGCT Fuse |
Remove the PM-IGCT fuse from the No. 1 engine room relay block.
Disconnect the hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| *1 | No. 1 Engine Room Relay Block | - | - |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
*b | PM-IGCT Fuse Holder |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A48-4 (+B1) or 2 (PM-IGCT fuse holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| A49-1 (+B2) or 2 (PM-IGCT fuse holder) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU connector.
Install the PM-IGCT fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block |
| *2 | PM-IGCT Fuse |
| *3 | IGCT-IG Fuse |
| *4 | IGCT Relay |
Disconnect the IGCT-IG fuse, PM-IGCT fuse and IGCT relay from the No. 1 engine room relay block.
| *1 | No. 1 Engine Room Relay Block |
| *a | PM-IGCT Fuse Holder |
| *b | IGCT-IG Fuse Holder |
| *c | IGCT Relay Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (IGCT relay holder) or 2 (IGCT-IG fuse holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| 5 (IGCT relay holder) or 1 (PM-IGCT fuse holder) - Body ground and other terminals | Always | 10 kΩ or higher |
Install the IGCT-IG fuse, PM-IGCT fuse and IGCT relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT