Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404407 MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P034000  Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor  P034031  Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor No Signal  


DESCRIPTION

If the cam position signal pulse sent from the ECM via a direct line is abnormal, the motor generator control ECU (MG ECU) (built into the inverter with converter assembly) stores DTC P034000 or P034031.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P034000 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor GI signal (camshaft position sensor) is not input for 2 sec. or more while the engine is running*
(1 trip detection logic)
·

SFI system

·

Inverter with converter assembly

·

ECM

·

Wire harness or connector


Does not come on Master Warning
Comes on
P034031 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor No Signal GI signal (camshaft position sensor) is not input for 2 sec. or more while the engine is running*
(1 trip detection logic)
·

SFI system

·

Inverter with converter assembly

·

ECM

·

Wire harness or connector


Does not come on Master Warning
Comes on

HINT:

*: When this DTC is stored, vibration may occur when the engine is stopped.


Related Data List
DTC No. Data List
P034000
P034031
·

Crank Position (Hybrid control system)

·

Engine Speed (Hybrid control system)



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY).

7.

With the vehicle stopped, move the shift lever to P.

8.

Depress the accelerator pedal to start the engine.

9.

Depress the accelerator pedal and maintain the engine speed at 1000 rpm or more for 5 seconds or more.

NOTICE:

As the state of charge of the HV battery may be low after driving in fail-safe mode, it will automatically be charged for 5 to 10 minutes with power switch on (READY) after repairs have been performed.


10.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

11.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A394771E04
0.052,1.49 1.219,1.875 1.167,0.385 10 false Camshaft Position Sensor 4.938,2.781 7.031,3.188 2.094,0.406 10 false Motor Generator Control ECU (Inverter with Converter Assembly) 2.031,1.125 2.271,1.344 0.24,0.219 10 false IC 3.073,0.927 3.469,1.115 0.396,0.188 10 false G2O 2.302,2.604 2.698,2.792 0.396,0.188 10 false ECM 1.208,2.167 1.604,2.354 0.396,0.188 10 false C63 1.573,2.156 1.969,2.344 0.396,0.188 10 false E1 1.26,1.99 1.656,2.177 0.396,0.188 10 false 59 3.438,1.031 3.833,1.219 0.396,0.188 10 false C63 3.469,0.854 3.865,1.042 0.396,0.188 10 false 70 4.656,0.917 4.917,1.115 0.26,0.198 10 false 10 4.656,2.115 5.052,2.302 0.396,0.188 10 false 24 4.927,0.938 5.323,1.125 0.396,0.188 10 false GI 4.927,2.229 5.323,2.417 0.396,0.188 10 false GND1 4.938,2.604 5.333,2.792 0.396,0.188 10 false C65 6.208,1 6.604,1.188 0.396,0.188 10 false 1MG 6.219,1.844 6.615,2.031 0.396,0.188 10 false 2MG

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
SFI system DTCs are not output. A
Any of the following DTCs are also output. B


Relevant Diagnosis
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal


e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL)

B

2.CHECK DTC OUTPUT (MOTOR GENERATOR CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
None of the following DTCs are output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P06B01C Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range
P06D61C Generator Control Module Offset Power Circuit Voltage Out of Range
P0A1B1F Generator Control Module Circuit Intermittent
P1C2B49 Drive Motor "A" Control Module A/D Converter Circuit Internal Electronic Failure
P1C2B1C Drive Motor "A" Control Module A/D Converter Circuit Voltage Out of Range
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect
P313487 Communication Error from Drive Motor "A" to Generator Missing Message
P313483 Communication Error from Drive Motor "A" to Generator Value of Signal Protection Calculation Incorrect
P313486 Communication Error from Drive Motor "A" to Generator Signal Invalid

HINT:

P034000 or P034031 may be stored due to a malfunction which also causes the DTCs in the preceding table to be stored. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.



e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - ECM)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - ECM)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the C65 inverter with converter assembly connector.


c.

Disconnect the C63 ECM connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A377957C03
0.323,0.896 0.688,1.146 0.365,0.25 1.417,2.469 1.781,2.719 0.365,0.25 0.979,3.344 0.979,4.021 true 1.688,1.073 1.688,2 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.115,2.281 0.427,2.479 0.313,0.198 10 false *b 0.385,0.938 0.844,1.135 0.458,0.198 10 false C65 1.479,2.5 1.938,2.698 0.458,0.198 10 false C63 1.625,2.063 1.938,2.26 0.313,0.198 10 false GI 0.844,4.115 1.302,4.313 0.458,0.198 10 false G2O
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C65-10 (GI) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector and ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C65-10 (GI) - C63-70 (G2O) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C65-10 (GI) or C63-70 (G2O) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the C63 ECM connector.


k.

Reconnect the C65 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM
a.

Disconnect the A38 and C63 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

A377956C07
2.51,0.51 2.906,0.76 0.396,0.25 1.01,1.26 1.01,2.135 true 3.458,1.313 3.458,2.125 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 2.594,0.552 3.052,0.75 0.458,0.198 10 false C63 3.354,2.188 3.813,2.385 0.458,0.198 10 false G2O 0.927,2.188 1.24,2.385 0.313,0.198 10 false E1
*a Component without harness connected
(ECM)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
C63-70 (G2O) - C63-59 (E1) Power switch off 10 kΩ or higher



c.

Reconnect the A38 and C63 ECM connectors.


Result:
Proceed to
OK
NG



OK

NG