Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404407 MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0A1B1F  Generator Control Module Circuit Intermittent  


DESCRIPTION

If the motor generator control ECU, which is built into in the inverter with converter assembly, is reset due to a problem with the power source in the inverter, the motor generator control ECU will stored this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A1B1F Generator Control Module Circuit Intermittent Error in reset signal from the inverter assembly power source IC:
If internal power source voltage drops below the normal CPU operating voltage or the ROM/RAM is malfunctioning, the power source IC resets the MG ECU and stores this DTC.
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly


Comes on Master Warning
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 15 seconds or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A389530E02
0.135,1.167 1.01,1.625 0.875,0.458 10 false from Auxiliary Battery 1.375,1.333 1.948,1.521 0.573,0.188 10 false IGCT-IG 2.448,1.906 3.021,2.094 0.573,0.188 10 false IGCT 3.552,1.417 4.125,1.604 0.573,0.188 10 false PCU FR 3.719,2.281 4.292,2.469 0.573,0.188 10 false MREL 3.646,3.24 4.219,3.427 0.573,0.188 10 false A48 3.635,3.396 4.563,3.781 0.927,0.385 10 false Hybrid Vehicle Control ECU 5.385,3.552 5.958,3.74 0.573,0.188 10 false C65 5.396,3.729 6.906,4.26 1.51,0.531 10 false Motor Generator Control ECU (Inverter with Converter Assembly) 5.49,1.708 6.063,1.896 0.573,0.188 10 false +B2 5.51,2.427 6.083,2.615 0.573,0.188 10 false GND1 5.5,2.906 6.073,3.094 0.573,0.188 10 false GND2 5.49,1.167 6.063,1.354 0.573,0.188 10 false +B 5.302,1.094 5.49,1.271 0.188,0.177 10 false 6 5.302,1.615 5.49,1.792 0.188,0.177 10 false 5 5.25,2.344 5.448,2.594 0.198,0.25 10 false 24 5.24,2.833 5.438,3.083 0.198,0.25 10 false 23 4.083,1.104 4.281,1.354 0.198,0.25 10 false 2 3.469,1.104 3.667,1.354 0.198,0.25 10 false 1 2.938,1.094 3.135,1.344 0.198,0.25 10 false 5 2.927,1.521 3.125,1.771 0.198,0.25 10 false 1 2.188,1.51 2.385,1.76 0.198,0.25 10 false 2 2.188,1.104 2.385,1.354 0.198,0.25 10 false 3 1.813,1.104 2.01,1.354 0.198,0.25 10 false 2 1.375,1.104 1.573,1.354 0.198,0.25 10 false 1 3.542,2.198 3.74,2.448 0.198,0.25 10 false 6

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P0A1B1F only is output. A
DTCs of hybrid control system in the tables below are output. B
DTCs of motor generator control system in the tables below are output. C


Malfunction Content System Relevant DTC
Communication malfunction Motor generator control system P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message
Hybrid control system P312387 Lost Communication with Missing Message
U011087 Lost Communication with Drive Motor Control Module "A" Missing Message


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

C

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the C65 inverter with converter assembly connector.


c.

Remove the IGCT relay from the No. 1 engine room relay block and No. 1 junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

A394773C02
5.26,1.781 4.896,1.031 true 5.375,1.771 5.802,1.115 true 5.396,2.042 5.906,2.708 true 5.302,2.052 4.958,2.729 true 0.771,0.479 1.083,0.635 0.313,0.156 10 false *1 0.844,2.385 1.156,2.542 0.313,0.156 10 false *2 4.219,0.51 4.531,0.667 0.313,0.156 10 false *a 4.583,0.958 4.948,1.115 0.365,0.156 10 false +B2 5.865,0.969 6.177,1.125 0.313,0.156 10 false +B 5.75,2.75 6.25,2.927 0.5,0.177 10 false GND1 4.76,2.76 5.26,2.938 0.5,0.177 10 false GND2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly *2 IGCT Relay Holder
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
C65-6 (+B) - 5 (IGCT relay holder) Power switch off Below 1 Ω
C65-5 (+B2) - 5 (IGCT relay holder) Power switch off Below 1 Ω
C65-24 (GND1) - Body ground Power switch off Below 1 Ω
C65-23 (GND2) - Body ground Power switch off Below 1 Ω



e.

Install the IGCT relay.


f.

Reconnect the C65 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR