Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404407 MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P0E3116  DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Below Threshold  P0E3117  DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Above Threshold  P0E311F  DC/DC Converter Voltage Sensor "A"(VL) Circuit Intermittent  


DESCRIPTION

The motor generator control ECU, which is built into the inverter with converter assembly, detects pre-boosting high voltage (VL) using the voltage sensor in the boost converter to control boosting. The motor generator control ECU also monitors the boost converter voltage sensor signal line and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0E3116 DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Below Threshold Boost converter voltage (VL) signal is stuck (Low)
(1 trip detection logic)
Inverter with converter assembly Comes on Master Warning
Comes on
P0E3117 DC/DC Converter Voltage Sensor "A"(VL) Circuit Voltage Above Threshold Boost converter voltage (VL) signal is stuck (High)
(1 trip detection logic)
Inverter with converter assembly Comes on Master Warning
Comes on
P0E311F DC/DC Converter Voltage Sensor "A"(VL) Circuit Intermittent Boost converter voltage (VL) signal is stuck (Low) or (High) detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
Inverter with converter assembly Does not come on Master Warning
Does not come on

Related Data List
DTC No. Data List
P0E3116
P0E3117
P0E311F
·

Hybrid Battery Voltage

·

VH-Voltage after Boosting

·

VL-Voltage before Boosting



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395

d.

Check for DTCs.

Result:
Result Proceed to
P0E3116 only is output. A
P0E3117 and/or P0E311F are output, and none of the following DTCs are output. B
DTCs of hybrid control system in the tables below are output. C
DTCs of motor generator control system in the tables below are output. D


System Relevant Diagnosis
Hybrid control system P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Battery or Open
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Battery or Open
P1C8449 High Voltage Power Resource Circuit Short during Ready ON
P312387 Lost Communication with Missing Message
Motor generator control system P312487 Lost Communication between Drive Motor "A" and HV ECU Missing Message

HINT:

P0E3116, P0E3117 or P0E311F may be stored due to a malfunction which also causes the DTCs in the preceding table to be stored. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (MOTOR GENERATOR)

B

C

D

2.CHECK FREEZE FRAME DATA (MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


d.

Read the freeze frame data of DTC P0E3116.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
"VH-Voltage after Boosting" is less than 55 V. A
"VH-Voltage after Boosting" is 55 V or more. B



e.

Turn the power switch off.



A

3.CLEAR DTC

B

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395

e.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397
Powertrain > Motor Generator > Clear DTCs
50002 395

f.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

With the vehicle stopped, apply the parking brake and turn the power switch on (READY).

HINT:
·

If the power switch could not be turned on (READY), turn the power switch off and check for DTCs after turning the power switch on (READY) again.

·

Because P300449 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.




c.

Ensure the safety of the areas in front and at the back of the vehicle.


d.

Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.

HINT:

Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.



e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P1C8449 is output, or no DTCs are output. A
Power switch could not be turned on (READY) and DTC P300449 is output. B



g.

Turn the power switch off.



A

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

6.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

7.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the M42 HV battery junction block assembly connector.


d.

Disconnect the F2 hybrid vehicle control ECU connector.


e.
A389514C17
0.438,3.406 0.938,3.656 0.5,0.25 1.938,0.354 2.438,0.604 0.5,0.25 1.583,2.417 2.042,2.052 true 0.833,4.052 1.26,3.625 true 2.76,2.417 2.271,2.042 true 2.531,4.052 2.094,3.625 true 0.271,0.271 0.583,0.427 0.313,0.156 10 false *a 0.438,2.917 0.75,3.073 0.313,0.156 10 false *b 1.333,2.448 1.896,2.615 0.563,0.167 10 false SMRB 2.396,4.083 2.958,4.25 0.563,0.167 10 false SMRB 2.594,2.448 3.156,2.615 0.563,0.167 10 false SMRG 0.531,4.104 1.094,4.271 0.563,0.167 10 false SMRG 2.094,0.385 2.406,0.542 0.313,0.156 10 false F2 0.542,3.438 0.854,3.594 0.313,0.156 10 false M42
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-4 (SMRB) - M42-1 (SMRB) Power switch off Below 1 Ω
F2-1 (SMRG) - M42-4 (SMRG) Power switch off Below 1 Ω



f.

Reconnect the F2 hybrid vehicle control ECU connector.


g.

Reconnect the M42 HV battery junction block assembly connector.


h.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the M42 HV battery junction block assembly connector.


d.
A394838C04
0.406,0.708 0.958,0.969 0.552,0.26 1.063,1.646 1.552,1.167 true 0.833,1.667 1.292,1.865 0.458,0.198 10 false GND 0.542,0.76 1,0.958 0.458,0.198 10 false M42 0.104,0.104 0.479,0.344 0.375,0.24 12 false *a
*a Rear view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-3 (GND) - Body ground Power switch off Below 1 Ω



e.

Reconnect the M42 HV battery junction block assembly connector.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

10.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

11.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
11.CHECK HYBRID VEHICLE CONTROL ECU (CHECK FOR NORMAL OPERATION)
a.

Install the service plug grip.


b.

Turn the power switch on (IG).



d.

Turn the power switch off and wait for 30 seconds or more.


e.

Turn the power switch on (READY).


f.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Voltage, VL-Voltage before Boosting.


g.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > Hybrid Control > Data List
Tester Display
VL-Voltage before Boosting
Hybrid Battery Voltage
50003 397 150,227

Result:
Result Proceed to
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
Difference between "Hybrid Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more. B


h.

Turn the power switch off.



A

END

B