Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P06881F  ECM/PCM Power Relay Sense Circuit Intermittent  


DESCRIPTION

This DTC indicates that the hybrid vehicle control ECU detected an instantaneous interruption in +B power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P06881F ECM/PCM Power Relay Sense Circuit Intermittent When the power switch is on (READY), the hybrid vehicle control ECU is reset due to an instantaneous interruption of power source.
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU


Does not come on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Turn the power switch on (READY) and wait for 30 seconds or more.

(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Speed" for approximately 5 minutes.)

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A394803E04
0.927,2.719 2.146,2.979 1.219,0.26 10 false Auxiliary Battery 0.719,1.813 1.563,2.042 0.844,0.229 10 false BATT-MAIN 1.594,1.167 2.219,1.365 0.625,0.198 10 false IGCT-IG 3.208,1.76 3.833,1.958 0.625,0.198 10 false IGCT 2.927,0.938 3.146,1.177 0.219,0.24 10 false 3 2.927,1.344 3.219,1.521 0.292,0.177 10 false 2 3.74,0.938 3.958,1.177 0.219,0.24 10 false 5 3.74,1.344 3.958,1.583 0.219,0.24 10 false 1 3.906,1.167 4.583,1.375 0.677,0.208 10 false PM-IGCT 5.344,0.521 6.021,0.729 0.677,0.208 10 false A48 5.344,1.042 6.021,1.25 0.677,0.208 10 false A49 5.344,1.448 6.021,1.656 0.677,0.208 10 false A48 5.417,0.313 5.635,0.521 0.219,0.208 10 false 4 5.417,0.833 5.635,1.042 0.219,0.208 10 false 1 5.417,1.24 5.635,1.448 0.219,0.208 10 false 6 5.719,1.344 6.25,1.531 0.531,0.188 10 false MREL 5.719,1.021 6.188,1.24 0.469,0.219 10 false +B2 5.719,0.5 6.219,0.729 0.5,0.229 10 false +B1 5.615,2.458 6.563,2.896 0.948,0.438 10 false Hybrid Vehicle Control ECU

PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL
a.

Confirm whether the auxiliary battery terminals have been disconnected recently.

Result:
Result Proceed to
Terminals have been disconnected. A
Terminals have not been disconnected. B




A

2.CONFIRM MASTER WARNING

B

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
2.CONFIRM MASTER WARNING
a.

Turn the power switch on (READY) from off.


b.

Confirm that the master warning illuminates.

Result:
Result Proceed to
Master warning illuminates. A
Master warning does not illuminate. B


NOTICE:

DTC P06881F may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the power switch is turned off and then on (READY) again. In this case, clear the DTCs to complete the inspection.



c.

Turn the power switch off.



A

3.CLEAR DTC

B

END

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.

Powertrain > Hybrid Control > Trouble Codes
50001 397

e.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

f.

Turn the power switch off and wait for 2 minutes or more.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTC P06881F is output again. A
DTCs other than P06881F are also output. B



e.

Turn the power switch off.



A

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)

B

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the auxiliary battery terminal.

OK:

The terminal is connected securely and there is no contact problem.



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IGCT RELAY)

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IGCT RELAY)
a.

Remove the IGCT relay from the No. 1 engine room relay block.


b.

Disconnect the hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

A389505C01
4,0.917 4.5,1.167 0.5,0.25 4.542,0.917 5.042,1.167 0.5,0.25 4.583,3.083 4.458,2.469 true 5.167,3.073 4.833,2.469 true 0.354,0.167 0.667,0.323 0.313,0.156 10 false *1 2.042,1.583 2.354,1.74 0.313,0.156 10 false *b 3.573,0.667 3.885,0.823 0.313,0.156 10 false *a 4.479,3.135 4.875,3.302 0.396,0.167 10 false +B2 5.083,3.125 5.479,3.292 0.396,0.167 10 false +B1 4.125,0.938 4.583,1.135 0.458,0.198 10 false A49 4.667,0.938 5.125,1.135 0.458,0.198 10 false A48
*1 No. 1 Engine Room Relay Block - -
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b IGCT Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A48-4 (+B1) - 5 (IGCT relay holder) Power switch off Below 1 Ω
A49-1 (+B2) - 5 (IGCT relay holder) Power switch off Below 1 Ω



d.

Reconnect the hybrid vehicle control ECU connectors.


e.

Reinstall the IGCT relay.


Result:
Proceed to
OK
NG



OK

8.CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.


ii.

When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.



Result:
Result Proceed to
Problem symptom does not recur. A
Problem symptom recurs. B



A

B

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA