Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P212012  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery  P212014  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open  P21201C  Throttle/Pedal Position Sensor/Switch "D" Voltage Out of Range  P21201F  Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent  P212512  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery  P212514  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open  P21251C  Throttle/Pedal Position Sensor/Switch "E" Voltage Out of Range  P21251F  Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent  P213800  Throttle/Pedal Position Sensor/Switch "D"/" E" Voltage Correlation  P21382B  Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU calculates the accelerator pedal opening angle based on the output voltage of the main sensor (VPA) and sub sensor (VPA2) of the accelerator pedal sensor assembly. If the output voltage of either the main sensor (VPA) or sub sensor (VPA2) deviates, a malfunction will be detected.

The cause of this malfunction may be one of the following:

·

Accelerator pedal sensor assembly malfunction

·

Wire harness or connector malfunction

·

Hybrid vehicle control ECU malfunction



DESCRIPTION

The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and detects how much the pedal is depressed. This is a non-contact sensor with Hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA and VPA2 of the hybrid vehicle control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The hybrid vehicle control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA and VPA2.

A222964E85
0.76,2.708 0.76,3.427 0.76,3.427 0.854,3.427 false 0.76,1.615 0.76,0.75 0.76,0.75 0.865,0.75 false 0.74,2.01 0.219,0.385 0.219,0.385 0.302,0.385 false 0.75,2.354 0.198,3.813 0.198,3.813 0.281,3.813 false 6.677,1.208 6.677,0.365 6.677,0.365 6.417,0.365 false 6.552,1.427 6.552,3.51 6.552,3.51 6.292,3.51 false 0.875,0.698 1.417,0.917 0.542,0.219 10 false Magnet 0.333,0.313 1.188,0.479 0.854,0.167 10 false Hall Element 0.333,3.74 1.188,3.906 0.854,0.167 10 false Hall Element 0.875,3.354 1.385,3.521 0.51,0.167 10 false Magnet 1.74,3.542 3.135,3.948 1.396,0.406 10 false Hybrid Vehicle Control ECU 2.865,1.771 4.083,2.313 1.219,0.542 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.094,0.688 6.313,0.865 2.219,0.177 10 false Accelerator Pedal Opening Angle (°) 4.396,4.094 6.708,4.271 2.313,0.177 10 false *1: Accelerator Pedal Released 4.396,4.385 6.781,4.563 2.385,0.177 10 false *2: Accelerator Pedal Fully Depressed 0.198,4.063 1.323,4.396 1.125,0.333 10 false Accelerator Pedal Sensor Assembly 2.146,1.083 2.396,1.25 0.25,0.167 10 false 5 V 4.229,1.01 4.323,1.177 0.094,0.167 10 false 5 4.229,2.396 4.323,2.563 0.094,0.167 10 false 0 3.938,1.271 4.323,1.438 0.385,0.167 10 false 3.988 3.938,1.469 4.323,1.635 0.385,0.167 10 false 3.188 4.104,1.938 4.323,2.104 0.219,0.167 10 false 1.6 6.865,1.135 7.156,1.302 0.292,0.167 10 false 4.55 6.865,1.354 7.156,1.521 0.292,0.167 10 false 3.75 6.656,2.521 6.833,2.688 0.177,0.167 10 false 20 4.25,2.823 4.427,2.99 0.177,0.167 10 false *1 6.052,2.823 6.229,2.99 0.177,0.167 10 false *2 5.104,2.51 5.479,2.729 0.375,0.219 10 false 12.4 4.104,2.156 4.323,2.323 0.219,0.167 10 false 0.8 2.51,1.938 2.76,2.104 0.25,0.167 10 false 5 V 2.198,1.677 2.531,1.844 0.333,0.167 10 false AD 2.365,2.552 2.698,2.771 0.333,0.219 10 false AD 4.104,0.292 6.573,0.635 2.469,0.344 10 false VPA2: Malfunction Detection Sensor 4.854,3.448 6.385,3.656 1.531,0.208 10 false VPA: Control Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery Short to +B in the main sensor circuit:
The main sensor voltage is 4.8 V or more for 2 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open Open or short to ground in the main sensor circuit:
The main sensor voltage is 0.4 V or less for 0.5 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P21201C Throttle/Pedal Position Sensor/Switch "D" Voltage Out of Range Internal malfunction in the main sensor:
Main sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short).
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P21201F Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent Main sensor circuit wiring malfunction or level is not stable:
Main sensor voltage is 0.4 V or less or 4.8 V or more for a certain period of time.
(Both of the following conditions are met: The main sensor voltage is 0.4 V or less for a certain period of time and 4.8 V or more for a certain period of time.)
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery Short to +B in the sub sensor circuit:
Main sensor is normal and sub sensor voltage is 4.8 V or more for 2 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open Open or short to ground in the sub sensor circuit:
The sub sensor voltage is 1.2 V or less for 0.5 seconds.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P21251C Throttle/Pedal Position Sensor/Switch "E" Voltage Out of Range Internal malfunction of the sub sensor:
Sub sensor output changes rapidly (detected when there are no circuit malfunctions such as an open or short).
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P21251F Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent Sub sensor circuit wiring malfunction or level is not stable:
When the main sensor circuit is normal, the sub sensor voltage is 1.2 V or less or 4.8 V or more for a certain period of time.
(Both of the following conditions are met: Sub sensor voltage is 1.2 V or less for a certain period of time, and the main sensor is normal and sub sensor voltage is 4.8 V or more for a certain period of time.)
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P213800 Throttle/Pedal Position Sensor/Switch "D"/" E" Voltage Correlation Difference between the main sensor value and sub sensor value is large.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on
P21382B Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled Main or sub sensor circuit wiring malfunction:
The difference in voltage between the main sensor and sub sensor is 0.02 V or less, or a low output malfunction continues in both the main and sub sensors for a certain period of time.
(1 trip detection logic)
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


Comes on Master Warning: Comes on

Related Data List
DTC No. Data List
P212012
·

Accelerator Position Sensor No. 1 Voltage %

·

Accelerator Position Sensor No. 2 Voltage %


P212014
P21201C
P21201F
P212512
P212514
P21251C
P21251F
P213800
P21382B

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait for approximately 10 seconds with the power switch on (READY) and shift lever in P, then fully depress and release the accelerator pedal several times.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A299132E41
1.802,0.604 2.26,0.781 0.458,0.177 10 false VCPA 1.865,1.031 2.24,1.208 0.375,0.177 10 false VPA 1.896,1.479 2.24,1.667 0.344,0.188 10 false EPA 1.813,1.906 2.188,2.083 0.375,0.177 10 false VCP2 1.813,2.354 2.188,2.531 0.375,0.177 10 false VPA2 1.823,2.781 2.469,3.042 0.646,0.26 10 false EPA2 0.771,3.104 1.104,3.281 0.333,0.177 10 false A46 0.75,3.271 3.01,3.49 2.26,0.219 10 false Accelerator Pedal Sensor Assembly 5.031,3.208 6.917,3.49 1.885,0.281 10 false Hybrid Vehicle Control ECU 5.01,3.063 5.385,3.25 0.375,0.188 10 false A49 5.167,0.469 5.406,0.656 0.24,0.188 10 false 9 5.094,0.896 5.302,1.073 0.208,0.177 10 false 30 5.094,1.333 5.302,1.51 0.208,0.177 10 false 20 5.094,2.219 5.302,2.396 0.208,0.177 10 false 28 5.156,1.802 5.365,1.979 0.208,0.177 10 false 8 5.094,2.656 5.302,2.833 0.208,0.177 10 false 18 2.302,0.906 2.51,1.094 0.208,0.188 10 false 6 2.302,0.49 2.51,0.677 0.208,0.188 10 false 4 2.302,1.354 2.51,1.542 0.208,0.188 10 false 5 2.302,1.802 2.51,1.99 0.208,0.188 10 false 1 2.302,2.229 2.51,2.417 0.208,0.188 10 false 3 2.313,2.646 2.521,2.833 0.208,0.188 10 false 2 5.354,0.479 6.031,0.656 0.677,0.177 10 false VCPA 5.365,0.917 5.958,1.104 0.594,0.188 10 false VPA 5.375,1.354 5.938,1.573 0.563,0.219 10 false EPA 5.375,1.771 6.156,1.948 0.781,0.177 10 false VCP2 5.375,2.208 6.167,2.406 0.792,0.198 10 false VPA2 5.333,2.656 6,2.906 0.667,0.25 10 false EPA2 5.823,1.146 6.271,1.5 0.448,0.354 10 false 39 kΩ +/- 5% 5.823,2.469 6.292,2.833 0.469,0.365 10 false 39 kΩ +/- 5% 6.135,1.76 6.427,1.99 0.292,0.229 10 false 5 V 6.135,0.448 6.375,0.656 0.24,0.208 10 false 5 V

PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE %, ACCELERATOR POSITION SENSOR NO. 2 VOLTAGE %)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accelerator Position Sensor No. 1 Voltage %, Accelerator Position Sensor No. 2 Voltage %.

Powertrain > Hybrid Control > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %
50003 397 23,24

d.

Read the Data List.

Standard:
Tester Display Accelerator Pedal Condition Specified Condition
Accelerator Position Sensor No. 1 Voltage % Not depressed 10 to 22%
Fully depressed 52 to 90%
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively
Accelerator Position Sensor No. 2 Voltage % Not depressed 24 to 40%
Fully depressed 68 to 99%
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively



e.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
a.

Check the connector connections and contact pressure of the relevant terminals for the accelerator pedal sensor assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

A394770C01
0.073,0.146 0.302,0.354 0.229,0.208 12 true *A 3.656,0.135 3.885,0.344 0.229,0.208 12 true *B
*A for LHD *B for RHD


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK HYBRID VEHICLE CONTROL ECU (CHECK VOLTAGE)

NG

CONNECT SECURELY

4.CHECK HYBRID VEHICLE CONTROL ECU (CHECK VOLTAGE)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the power switch on (IG).


c.
A380541C50
0.396,0.979 0.781,1.208 0.385,0.229 0.948,1.688 1.292,1.104 true 1.365,1.698 1.49,1.125 true 2.052,1.708 1.802,1.125 true 2.479,1.677 1.99,1.125 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.458,1 0.917,1.198 0.458,0.198 10 false A46 0.781,1.708 1.396,1.906 0.615,0.198 10 false VCP2 1.219,1.719 1.833,1.917 0.615,0.198 10 false EPA2 1.917,1.74 2.531,1.938 0.615,0.198 10 false VCPA 2.406,1.729 2.865,1.927 0.458,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A46-4 (VCPA) - A46-5 (EPA) Power switch on (IG) 4.5 to 5.5 V
A46-1 (VCP2) - A46-2 (EPA2) Power switch on (IG) 4.5 to 5.5 V



d.

Turn the power switch off.


e.

Reconnect the accelerator pedal sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HYBRID VEHICLE CONTROL ECU (CHECK RESISTANCE)

NG

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
5.CHECK HYBRID VEHICLE CONTROL ECU (CHECK RESISTANCE)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.
A380541C51
0.396,0.979 0.781,1.208 0.385,0.229 1.51,1.708 1.656,1.125 true 1.135,1.688 1.49,1.125 true 2.552,1.708 2.125,1.125 true 2.24,1.708 1.99,1.125 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.469,1.021 0.927,1.219 0.458,0.198 10 false A46 1.365,1.729 1.979,1.927 0.615,0.198 10 false VPA2 0.99,1.708 1.604,1.906 0.615,0.198 10 false EPA2 2.479,1.729 3.094,1.927 0.615,0.198 10 false VPA 2.135,1.74 2.594,1.938 0.458,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A46-6 (VPA) - A46-5 (EPA) Power switch off 28.00 to 41.61 kΩ
A46-3 (VPA2) - A46-2 (EPA2) Power switch off 28.00 to 41.61 kΩ



c.

Reconnect the accelerator pedal sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Turn the power switch on (IG).


d.
A389518C01
0.677,0.219 1.177,0.469 0.5,0.25 0.271,3.271 0.771,3.521 0.5,0.25 2.583,4 1.99,3.49 true 2.167,4.167 1.823,3.5 true 1.167,4.167 1.438,3.5 true 0.75,4 1.271,3.49 true 1.25,2.573 1.01,2.052 true 0.583,2.583 0.906,2.052 true 1.406,2.083 1.01,1.979 true 1.333,1.75 0.958,1.969 true 0.083,0.135 0.396,0.292 0.313,0.156 10 false *a 0.073,2.875 0.385,3.031 0.313,0.156 10 false *b 1.438,1.667 2,1.833 0.563,0.167 10 false VCPA 1.583,2.083 2.146,2.25 0.563,0.167 10 false VCP2 1.188,2.667 1.75,2.833 0.563,0.167 10 false EPA2 0.271,2.583 0.833,2.75 0.563,0.167 10 false EPA 2.552,4.031 3.115,4.198 0.563,0.167 10 false EPA 2.021,4.208 2.583,4.375 0.563,0.167 10 false VCPA 1,4.208 1.563,4.375 0.563,0.167 10 false EPA2 0.521,4.031 1.083,4.198 0.563,0.167 10 false VCP2 0.385,3.302 0.698,3.458 0.313,0.156 10 false A46 0.802,0.25 1.115,0.406 0.313,0.156 10 false A49
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-9 (VCPA) - Body ground Power switch on (IG) Below 1 V
A49-20 (EPA) - Body ground Power switch on (IG) Below 1 V
A49-8 (VCP2) - Body ground Power switch on (IG) Below 1 V
A49-18 (EPA2) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A49-9 (VCPA) - A46-4 (VCPA) Power switch off Below 1 Ω
A49-20 (EPA) - A46-5 (EPA) Power switch off Below 1 Ω
A49-8 (VCP2) - A46-1 (VCP2) Power switch off Below 1 Ω
A49-18 (EPA2) - A46-2 (EPA2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A49-9 (VCPA) or A46-4 (VCPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A49-20 (EPA) or A46-5 (EPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A49-8 (VCP2) or A46-1 (VCP2) - Body ground and other terminals Power switch off 10 kΩ or higher
A49-18 (EPA2) or A46-2 (EPA2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the accelerator pedal sensor assembly connector.


h.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Turn the power switch on (IG).


d.
A389518C22
0.552,0.219 1.042,0.469 0.49,0.25 0.219,3.292 0.708,3.542 0.49,0.25 0.833,4.083 1.417,3.5 true 1.365,4.167 1.615,3.51 true 2.25,4.167 1.958,3.5 true 2.75,4 2.125,3.49 true 0.417,2.583 0.906,2.052 true 1.25,2.417 1.01,2.115 true 1,2.573 0.917,2.115 true 1.25,1.833 1.01,2.042 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.073,2.927 0.385,3.083 0.313,0.156 10 false *b 1.333,1.719 1.896,1.885 0.563,0.167 10 false EPA2 1.198,2.438 1.76,2.604 0.563,0.167 10 false VPA2 0.885,2.625 1.448,2.792 0.563,0.167 10 false VPA 0.271,2.625 0.833,2.792 0.563,0.167 10 false EPA 2.156,4.198 2.719,4.365 0.563,0.167 10 false EPA 2.729,4.031 3.292,4.198 0.563,0.167 10 false VPA 1.198,4.198 1.76,4.365 0.563,0.167 10 false VPA2 0.594,4.115 1.156,4.281 0.563,0.167 10 false EPA2 0.333,3.323 0.646,3.479 0.313,0.156 10 false A46 0.667,0.25 0.979,0.406 0.313,0.156 10 false A49
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (VPA) - Body ground Power switch on (IG) Below 1 V
A49-28 (VPA2) - Body ground Power switch on (IG) Below 1 V
A49-20 (EPA) - Body ground Power switch on (IG) Below 1 V
A49-18 (EPA2) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A49-30 (VPA) - A46-6 (VPA) Power switch off Below 1 Ω
A49-20 (EPA) - A46-5 (EPA) Power switch off Below 1 Ω
A49-28 (VPA2) - A46-3 (VPA2) Power switch off Below 1 Ω
A49-18 (EPA2) - A46-2 (EPA2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A49-30 (VPA) or A46-6 (VPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A49-20 (EPA) or A46-5 (EPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A49-28 (VPA2) or A46-3 (VPA2) - Body ground and other terminals Power switch off 10 kΩ or higher
A49-18 (EPA2) or A46-2 (EPA2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the accelerator pedal sensor assembly connector.


h.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR