Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) J

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  ECU Power Source Circuit  


DESCRIPTION

If the power switch is on (IG), the hybrid vehicle control ECU applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM

A394813E08
0.052,2.635 1.115,2.865 1.063,0.229 10 false Auxiliary Battery 1.625,1.969 3.74,2.271 2.115,0.302 10 false No. 1 Engine Room Relay Block 2.51,1.573 2.896,1.76 0.385,0.188 10 false IGCT 1.604,0.708 1.76,0.906 0.156,0.198 10 false 1 2.031,0.708 2.188,0.906 0.156,0.198 10 false 2 2.24,0.708 2.396,0.906 0.156,0.198 10 false 3 2.24,1.125 2.396,1.323 0.156,0.198 10 false 2 1.615,0.969 2.167,1.146 0.552,0.177 10 false IGCT-IG 3.01,1.125 3.167,1.323 0.156,0.198 10 false 1 3.01,0.708 3.167,0.906 0.156,0.198 10 false 5 3.219,0.708 3.375,0.906 0.156,0.198 10 false 1 3.635,0.708 3.792,0.906 0.156,0.198 10 false 2 3.198,0.979 3.823,1.167 0.625,0.188 10 false PM-IGCT 5.979,0.375 6.438,0.573 0.458,0.198 10 false +B1 5.615,0.375 5.896,0.563 0.281,0.188 10 false A48 5.698,0.188 5.854,0.385 0.156,0.198 10 false 4 5.615,0.802 5.896,0.99 0.281,0.188 10 false A49 5.615,1.229 5.896,1.417 0.281,0.188 10 false A48 5.698,0.615 5.854,0.813 0.156,0.198 10 false 1 5.698,1.042 5.854,1.24 0.156,0.198 10 false 6 5.667,3.354 7.031,3.698 1.365,0.344 10 false Hybrid Vehicle Control ECU 5.979,0.802 6.438,1 0.458,0.198 10 false +B2 5.979,1.229 6.594,1.427 0.615,0.198 10 false MREL 5.656,1.656 5.896,1.833 0.24,0.177 10 false F3 5.656,2.521 5.896,2.698 0.24,0.177 10 false F3 5.656,2.083 5.896,2.26 0.24,0.177 10 false F2 5.656,2.948 5.896,3.125 0.24,0.177 10 false F2 5.698,1.469 5.854,1.667 0.156,0.198 10 false 4 5.698,1.896 5.854,2.094 0.156,0.198 10 false 5 5.698,2.323 5.854,2.521 0.156,0.198 10 false 5 5.698,2.76 5.854,2.958 0.156,0.198 10 false 6 5.99,1.656 6.344,1.844 0.354,0.188 10 false E12 5.99,2.083 6.344,2.271 0.354,0.188 10 false E01 5.99,2.521 6.344,2.708 0.354,0.188 10 false E02 5.979,2.948 6.333,3.135 0.354,0.188 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU (+B1, +B2 VOLTAGE)
a.

Turn the power switch on (IG).


b.
A389500C16
0.583,0.917 1,1.167 0.417,0.25 1.25,0.917 1.667,1.167 0.417,0.25 1.281,2.427 1.01,1.719 true 1.938,2.417 1.396,1.729 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.167,2.427 1.51,2.625 0.344,0.198 10 false +B2 1.823,2.417 2.385,2.583 0.563,0.167 10 false +B1 0.677,0.958 1.135,1.156 0.458,0.198 10 false A49 1.333,0.958 1.792,1.156 0.458,0.198 10 false A48
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-4 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A49-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A389532C01
2.417,0.5 2.833,0.75 0.417,0.25 1.833,0.5 2.25,0.75 0.417,0.25 1.198,3.135 1.813,2.354 true 1.625,3.135 1.896,2.375 true 2.313,3.146 2.604,2.365 true 2.979,3.146 2.677,2.365 true 0.177,0.135 0.49,0.292 0.313,0.156 10 false *a 1.104,3.146 1.417,3.302 0.313,0.156 10 false E1 1.521,3.156 1.833,3.313 0.313,0.156 10 false E01 2.167,3.156 2.479,3.313 0.313,0.156 10 false E02 2.906,3.146 3.219,3.302 0.313,0.156 10 false E12 1.969,0.542 2.281,0.74 0.313,0.198 10 false F2 2.552,0.542 2.865,0.74 0.313,0.198 10 false F3
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-6 (E1) - Body ground Always Below 1 Ω
F2-5 (E01) - Body ground Always Below 1 Ω
F3-5 (E02) - Body ground Always Below 1 Ω
F3-4 (E12) - Body ground Always Below 1 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)
a.

Turn the power switch on (IG).


b.
A389500C17
1.167,1 1.583,1.25 0.417,0.25 0.917,2.417 1.25,1.719 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.521,2.427 0.958,2.615 0.438,0.188 10 false MREL 1.25,1.042 1.708,1.24 0.458,0.198 10 false A48
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-6 (MREL) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK FUSE (PM-IGCT)

NG

4.CHECK FUSE (PM-IGCT)
a.
A389533C01
2.615,1.698 1.729,1.219 true 0.125,0.115 0.438,0.271 0.313,0.156 10 false *1 2.667,1.615 2.979,1.771 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 PM-IGCT Fuse


Remove the PM-IGCT fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PM-IGCT fuse terminals Always Below 1 Ω



c.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK FUSE (IGCT-IG)

NG

11.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - HYBRID VEHICLE CONTROL ECU)
5.CHECK FUSE (IGCT-IG)
a.
A389508C01
2.688,1.979 1.958,1.333 true 0.354,0.167 0.667,0.323 0.313,0.156 10 false *1 2.74,2.01 3.052,2.167 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT-IG Fuse


Remove the IGCT-IG fuse from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT-IG fuse terminals Always Below 1 Ω



c.

Install the IGCT-IG fuse.


Result:
Proceed to
OK
NG



OK

6.INSPECT RELAY (IGCT)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK)
6.INSPECT RELAY (IGCT)
a.
A389507C01
2.583,2.667 1.625,2.052 true 0.354,0.167 0.667,0.323 0.313,0.156 10 false *1 2.625,2.635 2.938,2.792 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT Relay


Remove the IGCT relay from the No. 1 engine room relay block.


b.
A253297C01
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE RELAY (IGCT)

7.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A389533C01
2.615,1.698 1.729,1.219 true 0.125,0.115 0.438,0.271 0.313,0.156 10 false *1 2.667,1.615 2.979,1.771 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 PM-IGCT Fuse


Remove the PM-IGCT fuse from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

A389534C01
0.917,1 1.333,1.25 0.417,0.25 1.417,1 1.833,1.25 0.417,0.25 1.521,3.26 1.302,2.51 true 2.021,3.26 1.635,2.51 true 4.406,0.313 4.719,0.469 0.313,0.156 10 false *1 0.427,0.927 0.74,1.083 0.313,0.156 10 false *a 6.281,1.208 6.594,1.365 0.313,0.156 10 false *b 1.406,3.26 1.719,3.417 0.313,0.156 10 false +B2 1.917,3.26 2.229,3.417 0.313,0.156 10 false +B1 1,1.042 1.458,1.24 0.458,0.198 10 false A49 1.5,1.042 1.958,1.24 0.458,0.198 10 false A48
*1 No. 1 Engine Room Relay Block - -
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b PM-IGCT Fuse Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A48-4 (+B1) - 2 (PM-IGCT fuse holder) Always Below 1 Ω
A49-1 (+B2) - 2 (PM-IGCT fuse holder) Always Below 1 Ω



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK)
a.
A389535C01
1.75,1.219 2.677,0.625 true 2.01,1.354 2.604,1.51 true 0.5,2.563 1.417,2.125 true 0.323,0.063 0.635,0.219 0.313,0.156 10 false *1 2.719,0.521 3.031,0.677 0.313,0.156 10 false *2 2.656,1.438 2.969,1.594 0.313,0.156 10 false *3 0.313,2.469 0.625,2.625 0.313,0.156 10 false *4
*1 No. 1 Engine Room Relay Block
*2 PM-IGCT Fuse
*3 IGCT-IG Fuse
*4 IGCT Relay


Remove the IGCT-IG fuse, PM-IGCT fuse and IGCT relay from the No. 1 engine room relay block.


b.
A389536C01
0.167,0.073 0.479,0.229 0.313,0.156 10 false *1 0.104,0.625 0.417,0.781 0.313,0.156 10 false *a 2.656,0.521 2.969,0.677 0.313,0.156 10 false *b 2.615,1.604 2.927,1.76 0.313,0.156 10 false *c
*1 No. 1 Engine Room Relay Block
*a PM-IGCT Fuse Holder
*b IGCT-IG Fuse Holder
*c IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay holder) - 2 (IGCT-IG fuse holder) Always Below 1 Ω
5 (IGCT relay holder) - 1 (PM-IGCT fuse holder) Always Below 1 Ω



c.

Install the IGCT-IG fuse, PM-IGCT fuse and IGCT relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 ENGINE ROOM RELAY BLOCK)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A389507C01
2.583,2.667 1.625,2.052 true 0.354,0.167 0.667,0.323 0.313,0.156 10 false *1 2.625,2.635 2.938,2.792 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT Relay


Remove the IGCT relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

A389537C01
5.167,1.083 5.583,1.333 0.417,0.25 4.75,3 5.219,2.594 true 0.521,0.5 0.833,0.656 0.313,0.156 10 false *1 4.365,2.927 4.865,3.083 0.5,0.156 10 false MREL 4.021,0.51 4.333,0.667 0.313,0.156 10 false *a 2.333,1.875 2.646,2.031 0.313,0.156 10 false *b 5.25,1.125 5.708,1.323 0.458,0.198 10 false A48
*1 No. 1 Engine Room Relay Block - -
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b IGCT Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A48-6 (MREL) - 1 (IGCT relay holder) Always Below 1 Ω
A48-6 (MREL) or 1 (IGCT relay holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT relay.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - BODY GROUND)
a.
A389507C01
2.583,2.667 1.625,2.052 true 0.354,0.167 0.667,0.323 0.313,0.156 10 false *1 2.625,2.635 2.938,2.792 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 IGCT Relay


Remove the IGCT relay from the No. 1 engine room relay block.


b.
A389517C01
0.25,0.104 0.563,0.302 0.313,0.198 10 false *1 2.438,1.479 2.75,1.677 0.313,0.198 10 false *a
*1 No. 1 Engine Room Relay Block
*a IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT relay holder) - Body ground Always Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK - HYBRID VEHICLE CONTROL ECU)
a.
A389533C01
2.615,1.698 1.729,1.219 true 0.125,0.115 0.438,0.271 0.313,0.156 10 false *1 2.667,1.615 2.979,1.771 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 PM-IGCT Fuse


Remove the PM-IGCT fuse from the No. 1 engine room relay block.


b.

Disconnect the hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

A389534C01
0.917,1 1.333,1.25 0.417,0.25 1.417,1 1.833,1.25 0.417,0.25 1.521,3.26 1.302,2.51 true 2.021,3.26 1.635,2.51 true 4.406,0.313 4.719,0.469 0.313,0.156 10 false *1 0.427,0.927 0.74,1.083 0.313,0.156 10 false *a 6.281,1.208 6.594,1.365 0.313,0.156 10 false *b 1.406,3.26 1.719,3.417 0.313,0.156 10 false +B2 1.917,3.26 2.229,3.417 0.313,0.156 10 false +B1 1,1.042 1.458,1.24 0.458,0.198 10 false A49 1.5,1.042 1.958,1.24 0.458,0.198 10 false A48
*1 No. 1 Engine Room Relay Block - -
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b PM-IGCT Fuse Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A48-4 (+B1) or 2 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher
A49-1 (+B2) or 2 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (PM-IGCT)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (NO. 1 ENGINE ROOM RELAY BLOCK)
a.
A389535C01
1.75,1.219 2.677,0.625 true 2.01,1.354 2.604,1.51 true 0.5,2.563 1.417,2.125 true 0.323,0.063 0.635,0.219 0.313,0.156 10 false *1 2.719,0.521 3.031,0.677 0.313,0.156 10 false *2 2.656,1.438 2.969,1.594 0.313,0.156 10 false *3 0.313,2.469 0.625,2.625 0.313,0.156 10 false *4
*1 No. 1 Engine Room Relay Block
*2 PM-IGCT Fuse
*3 IGCT-IG Fuse
*4 IGCT Relay


Disconnect the IGCT-IG fuse, PM-IGCT fuse and IGCT relay from the No. 1 engine room relay block.


b.
A389536C01
0.167,0.073 0.479,0.229 0.313,0.156 10 false *1 0.104,0.625 0.417,0.781 0.313,0.156 10 false *a 2.656,0.521 2.969,0.677 0.313,0.156 10 false *b 2.615,1.604 2.927,1.76 0.313,0.156 10 false *c
*1 No. 1 Engine Room Relay Block
*a PM-IGCT Fuse Holder
*b IGCT-IG Fuse Holder
*c IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay holder) or 2 (IGCT-IG fuse holder) - Body ground and other terminals Always 10 kΩ or higher
5 (IGCT relay holder) or 1 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher


c.

Install the IGCT-IG fuse, PM-IGCT fuse and IGCT relay.


Result:
Proceed to
OK
NG



OK

REPLACE RELAY (IGCT-IG)

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PM-IGCT)

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT-IG)