Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) J

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  Indicator Circuit  


DESCRIPTION

In accordance with the shift lever position, each shift position indicator light will turn on.

WIRING DIAGRAM

A452238E03
0.052,0.792 1.198,1.021 1.146,0.229 10 false from ACC Relay 1.417,0.969 2.49,1.167 1.073,0.198 10 false ECU-ACC 2.385,0.938 2.656,1.167 0.271,0.229 10 false 1 2.583,0.844 3.042,1.042 0.458,0.198 10 false PWR 3.594,0.865 3.75,1.063 0.156,0.198 10 false P 3.594,1.281 3.75,1.479 0.156,0.198 10 false R 3.594,1.708 3.75,1.927 0.156,0.219 10 false N 3.604,2.135 3.76,2.354 0.156,0.219 10 false D 3.604,2.563 3.76,2.781 0.156,0.219 10 false B 3.813,0.979 4.125,1.271 0.313,0.292 10 false 10 3.813,1.406 3.969,1.604 0.156,0.198 10 false 9 3.813,1.833 3.969,2.031 0.156,0.198 10 false 8 3.813,2.26 3.969,2.458 0.156,0.198 10 false 7 3.813,2.688 3.969,2.885 0.156,0.198 10 false 6 5.656,0.344 6.271,0.542 0.615,0.198 10 false ACCI 5.667,0.865 6.281,1.063 0.615,0.198 10 false INDP 5.667,1.281 6.281,1.479 0.615,0.198 10 false INDR 5.667,1.698 6.281,1.896 0.615,0.198 10 false INDN 5.677,2.156 6.292,2.354 0.615,0.198 10 false INDD 5.677,2.573 6.292,2.771 0.615,0.198 10 false INDB 5.333,0.156 5.646,0.354 0.313,0.198 10 false 22 5.333,0.646 5.646,0.844 0.313,0.198 10 false 13 5.375,1.073 5.688,1.271 0.313,0.198 10 false 8 5.333,1.5 5.646,1.698 0.313,0.198 10 false 12 5.333,1.938 5.646,2.135 0.313,0.198 10 false 11 5.333,2.354 5.646,2.552 0.313,0.198 10 false 10 5.292,0.344 5.75,0.542 0.458,0.198 10 false A49 5.344,0.854 5.958,1.052 0.615,0.198 10 false F3 5.333,1.281 5.948,1.479 0.615,0.198 10 false F2 5.333,1.698 5.948,1.896 0.615,0.198 10 false F3 5.333,2.125 5.948,2.323 0.615,0.198 10 false F3 5.333,2.542 5.948,2.74 0.615,0.198 10 false F3 2.167,3.042 2.479,3.24 0.313,0.198 10 false F63 2.177,3.219 4.219,3.594 2.042,0.375 10 false Shift Position Indicator (Position Indicator Housing Assembly) 5.198,3.188 6.979,3.646 1.781,0.458 10 false Hybrid Vehicle Control ECU 2.385,2.594 2.656,2.823 0.271,0.229 10 false 5 2.583,2.479 3.042,2.677 0.458,0.198 10 false E

PROCEDURE

1.CHECK SHIFT POSITION INDICATOR
a.

Turn the power switch on (ACC).


b.

Check that each shift position indicator light turns on correctly.

Result:
Result Proceed to
All shift position indicator lights turn on simultaneously A
Shift position indicator lights other than corresponding one turn on B
Corresponding shift position indicator light does not turn on C
No shift position indicator lights turn on D



c.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

B

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

C

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

D

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A389532C24
2.417,0.5 2.833,0.75 0.417,0.25 1.833,0.5 2.25,0.75 0.417,0.25 1.76,3.052 2.188,2.438 true 2.479,3.042 2.698,2.427 true 2.177,3.042 2.646,2.427 true 2.792,3.031 2.75,2.438 true 3.01,2.802 2.792,2.438 true 0.177,0.135 0.49,0.292 0.313,0.156 10 false *a 1.448,3.052 1.844,3.26 0.396,0.208 10 false INDR 3.01,2.802 3.385,2.99 0.375,0.188 10 false INDB 2.656,3.052 3.104,3.229 0.448,0.177 10 false INDD 1.896,3.052 2.271,3.281 0.375,0.229 10 false INDP 1.969,0.542 2.281,0.74 0.313,0.198 10 false F2 2.552,0.542 2.865,0.74 0.313,0.198 10 false F3 2.281,3.052 2.656,3.281 0.375,0.229 10 false INDN
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-13 (INDP) - Body ground and other terminals Always 10 kΩ or higher
F2-8 (INDR) - Body ground and other terminals Always 10 kΩ or higher
F3-12 (INDN) - Body ground and other terminals Always 10 kΩ or higher
F3-11 (INDD) - Body ground and other terminals Always 10 kΩ or higher
F3-10 (INDB) - Body ground and other terminals Always 10 kΩ or higher



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR (POSITION INDICATOR HOUSING ASSEMBLY))
3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR (POSITION INDICATOR HOUSING ASSEMBLY))
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the shift position indicator (position indicator housing assembly) connector.


c.
A452239C01
1.885,0.052 2.302,0.302 0.417,0.25 0.417,3.417 0.833,3.667 0.417,0.25 2.438,0.052 2.854,0.302 0.417,0.25 0.917,3.917 1.333,3.75 true 1.208,4.229 1.542,3.781 true 1.594,4.24 1.729,3.771 true 1.979,4.24 1.896,3.792 true 2.406,4.281 2.083,3.76 true 1.76,2.354 2.188,1.844 true 2.479,2.458 2.719,1.833 true 2.219,2.438 2.667,1.844 true 2.802,1.833 3.094,2.458 true 2.865,2.708 2.76,1.833 true 0.271,0.063 0.583,0.219 0.313,0.156 10 false *a 0.25,2.76 0.563,2.917 0.313,0.156 10 false *b 1.458,2.365 1.917,2.563 0.458,0.198 10 false INDR 1.906,2.469 2.365,2.667 0.458,0.198 10 false INDP 2.74,2.76 3.198,2.958 0.458,0.198 10 false INDD 2.313,2.479 2.771,2.677 0.458,0.198 10 false INDN 3.01,2.479 3.385,2.688 0.375,0.208 10 false INDB 1.958,4.302 2.417,4.5 0.458,0.198 10 false R 2.375,4.302 2.833,4.5 0.458,0.198 10 false P 1.542,4.302 2,4.5 0.458,0.198 10 false N 1.125,4.302 1.583,4.5 0.458,0.198 10 false D 0.75,3.917 1.208,4.115 0.458,0.198 10 false B 0.51,3.458 0.969,3.656 0.458,0.198 10 false F63 2.031,0.094 2.49,0.292 0.458,0.198 10 false F2 2.583,0.094 3.042,0.292 0.458,0.198 10 false F3
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Position Indicator (Position Indicator Housing Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-13 (INDP) or F63-10 (P) - Body ground and other terminals Always 10 kΩ or higher
F2-8 (INDR) or F63-9 (R) - Body ground and other terminals Always 10 kΩ or higher
F3-12 (INDN) or F63-8 (N) - Body ground and other terminals Always 10 kΩ or higher
F3-11 (INDD) or F63-7 (D) - Body ground and other terminals Always 10 kΩ or higher
F3-10 (INDB) or F63-6 (B) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the shift position indicator (position indicator housing assembly) connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE SHIFT POSITION INDICATOR (POSITION INDICATOR HOUSING ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the shift position indicator connector.


b.

Turn the power switch on (ACC).


c.
A409139C04
0.458,0.948 0.844,1.208 0.385,0.26 0.948,0.667 1.344,1.021 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.531,1 0.844,1.198 0.313,0.198 10 false F63 0.552,0.531 0.969,0.76 0.417,0.229 10 false PWR
*a Front view of wire harness connector
(to Shift Position Indicator (Position Indicator Housing Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F63-1 (PWR) - Body ground Power switch on (ACC) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the shift position indicator connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)
a.

Turn the power switch on (ACC).


b.
A418457C02
0.583,0.917 1,1.167 0.417,0.25 1.156,2.417 0.823,1.854 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.156,2.448 1.646,2.646 0.49,0.198 10 false ACCI 0.677,0.958 1.135,1.156 0.458,0.198 10 false A49
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-22 (ACCI) - Body ground Power switch on (ACC) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Turn the power switch on (ACC).


c.
A389532C24
2.417,0.5 2.833,0.75 0.417,0.25 1.833,0.5 2.25,0.75 0.417,0.25 1.76,3.052 2.188,2.438 true 2.479,3.042 2.698,2.427 true 2.177,3.042 2.646,2.427 true 2.792,3.031 2.75,2.438 true 3.01,2.802 2.792,2.438 true 0.177,0.135 0.49,0.292 0.313,0.156 10 false *a 1.448,3.052 1.844,3.26 0.396,0.208 10 false INDR 3.01,2.802 3.385,2.99 0.375,0.188 10 false INDB 2.656,3.052 3.104,3.229 0.448,0.177 10 false INDD 1.896,3.052 2.271,3.281 0.375,0.229 10 false INDP 1.969,0.542 2.281,0.74 0.313,0.198 10 false F2 2.552,0.542 2.865,0.74 0.313,0.198 10 false F3 2.281,3.052 2.656,3.281 0.375,0.229 10 false INDN
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-13 (INDP) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F2-8 (INDR) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F3-12 (INDN) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F3-11 (INDD) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F3-10 (INDB) - Body ground and other terminals Power switch on (ACC) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR (POSITION INDICATOR HOUSING ASSEMBLY))
7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR (POSITION INDICATOR HOUSING ASSEMBLY))
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the shift position indicator connector.


c.
A452239C01
1.885,0.052 2.302,0.302 0.417,0.25 0.417,3.417 0.833,3.667 0.417,0.25 2.438,0.052 2.854,0.302 0.417,0.25 0.917,3.917 1.333,3.75 true 1.208,4.229 1.542,3.781 true 1.594,4.24 1.729,3.771 true 1.979,4.24 1.896,3.792 true 2.406,4.281 2.083,3.76 true 1.76,2.354 2.188,1.844 true 2.479,2.458 2.719,1.833 true 2.219,2.438 2.667,1.844 true 2.802,1.833 3.094,2.458 true 2.865,2.708 2.76,1.833 true 0.271,0.063 0.583,0.219 0.313,0.156 10 false *a 0.25,2.76 0.563,2.917 0.313,0.156 10 false *b 1.458,2.365 1.917,2.563 0.458,0.198 10 false INDR 1.906,2.469 2.365,2.667 0.458,0.198 10 false INDP 2.74,2.76 3.198,2.958 0.458,0.198 10 false INDD 2.313,2.479 2.771,2.677 0.458,0.198 10 false INDN 3.01,2.479 3.385,2.688 0.375,0.208 10 false INDB 1.958,4.302 2.417,4.5 0.458,0.198 10 false R 2.375,4.302 2.833,4.5 0.458,0.198 10 false P 1.542,4.302 2,4.5 0.458,0.198 10 false N 1.125,4.302 1.583,4.5 0.458,0.198 10 false D 0.75,3.917 1.208,4.115 0.458,0.198 10 false B 0.51,3.458 0.969,3.656 0.458,0.198 10 false F63 2.031,0.094 2.49,0.292 0.458,0.198 10 false F2 2.583,0.094 3.042,0.292 0.458,0.198 10 false F3
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Position Indicator (Position Indicator Housing Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-13 (INDP) - F63-10 (P) Always Below 1 Ω
F2-8 (INDR) - F63-9 (R) Always Below 1 Ω
F3-12 (INDN) - F63-8 (N) Always Below 1 Ω
F3-11 (INDD) - F63-7 (D) Always Below 1 Ω
F3-10 (INDB) - F63-6 (B) Always Below 1 Ω



d.

Reconnect the shift position indicator connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

REPLACE SHIFT POSITION INDICATOR (POSITION INDICATOR HOUSING ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR