Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404410 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  U115087  Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message  


DESCRIPTION

The battery ECU assembly transmits and receives signals via CAN communication to and from the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U115087 Lost Communication with Hybrid Powertrain Control Module (Hybrid/EV Battery Local Bus) Missing Message The battery ECU assembly does not receive any signals from the hybrid vehicle control ECU for 1 second or more.
(1 trip detection logic)
·

Battery ECU assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A399959E08
5.802,0.698 6.406,1.156 0.604,0.458 10 false +B1 5.802,1.167 6.406,1.625 0.604,0.458 10 false +B2 5.813,1.583 6.417,2.042 0.604,0.458 10 false MREL 5.448,0.521 6.052,0.979 0.604,0.458 10 false 4 5.385,0.729 5.99,1.188 0.604,0.458 10 false A48 5.448,0.969 6.052,1.427 0.604,0.458 10 false 1 5.385,1.146 5.99,1.604 0.604,0.458 10 false A49 5.479,1.375 6.083,1.833 0.604,0.458 10 false 6 5.396,1.552 6,2.01 0.604,0.458 10 false A48 3.646,1.323 4.25,1.781 0.604,0.458 10 false PM-IGCT 2.646,1.906 3.25,2.365 0.604,0.458 10 false IGCT 1.5,1.333 2.302,1.896 0.802,0.563 10 false IGCT-IG 0.813,4.49 2.25,5.052 1.438,0.563 10 false Auxiliary Battery 0.802,3.5 1.604,4.063 0.802,0.563 10 false BATT-MAIN 0.979,5.448 2.885,5.76 1.906,0.313 10 false : CAN Communication Line 1.448,1.031 1.698,1.354 0.25,0.323 10 false 1 1.948,1.031 2.198,1.354 0.25,0.323 10 false 2 3.635,1.042 3.885,1.365 0.25,0.323 10 false 1 4.167,1.031 4.417,1.354 0.25,0.323 10 false 2 3.115,1.469 3.365,1.792 0.25,0.323 10 false 1 2.375,1.458 2.719,1.708 0.344,0.25 10 false 2 2.365,1.063 2.708,1.313 0.344,0.25 10 false 3 3.125,1.021 3.469,1.271 0.344,0.25 10 false 5 5.208,5.094 7,5.51 1.792,0.417 10 false Hybrid Vehicle Control ECU 2.885,4.75 3.417,4.979 0.531,0.229 10 false z22 3.854,3.708 4.75,4 0.896,0.292 10 false CA1H 3.906,4.292 4.802,4.583 0.896,0.292 10 false CA1L 5.781,3.698 6.677,3.99 0.896,0.292 10 false CA4H 5.771,4.271 6.667,4.563 0.896,0.292 10 false CA4L 5.438,3.677 6.042,4.135 0.604,0.458 10 false F2 5.438,4.271 6.042,4.729 0.604,0.458 10 false F2 5.448,3.49 6.052,3.948 0.604,0.458 10 false 34 5.448,4.073 6.052,4.531 0.604,0.458 10 false 35 4.354,3.479 4.958,3.938 0.604,0.458 10 false 2 4.354,4.125 4.958,4.583 0.604,0.458 10 false 3 3.156,4.75 5.219,5.042 2.063,0.292 10 false Battery ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check and record any Hybrid Control DTCs and freeze frame data. Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs related to Hybrid Control are not output. A
DTCs related to Hybrid Control are output. B



e.

Turn the power switch off.



A

2.CHECK HYBRID VEHICLE CONTROL ECU (VOLTAGE)

B

2.CHECK HYBRID VEHICLE CONTROL ECU (VOLTAGE)
a.

Turn the power switch on (IG).


b.
A452417C01
0.604,0.948 1.021,1.198 0.417,0.25 1.198,0.948 1.615,1.198 0.417,0.25 0.667,2.5 1,1.688 true 1.75,2.5 1.385,1.688 true 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a 0.698,0.99 1.104,1.208 0.406,0.219 10 false A49 1.281,0.99 1.688,1.208 0.406,0.219 10 false A48 0.49,2.542 0.896,2.76 0.406,0.219 10 false +B2 1.615,2.542 2.021,2.76 0.406,0.219 10 false +B1
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-4 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A49-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the hybrid vehicle control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU and battery ECU assembly is not loose or disconnected.





d.

Disconnect the battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A452340C01
1.021,1.604 1.427,1.865 0.406,0.26 1.615,2.49 2.021,2.75 0.406,0.26 2.094,1.698 2.5,1.542 true 2,1.688 2.417,1.354 true 2.104,4.302 2.323,3.969 true 2.698,4.313 2.458,3.969 true 0.531,0.073 1.115,0.625 0.583,0.552 10 false *a 0.688,2.365 1.177,2.729 0.49,0.365 10 false *b 1.135,1.656 1.625,2.021 0.49,0.365 10 false z22 1.75,2.542 2.063,2.74 0.313,0.198 10 false F2 2.542,1.458 3.031,1.823 0.49,0.365 10 false CA1H 2.448,1.25 2.938,1.615 0.49,0.365 10 false CA1L 1.896,4.354 2.385,4.563 0.49,0.208 10 false CA4H 2.552,4.354 2.979,4.594 0.427,0.24 10 false CA4L
*a Rear view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z22-2 (CA1H) - F2-34 (CA4H) Power switch off Below 1 Ω
z22-3 (CA1L) - F2-35 (CA4L) Power switch off Below 1 Ω
F2-34 (CA4H) - Other terminals and body ground Power switch off 10 kΩ or higher
F2-35 (CA4L) - Other terminals and body ground Power switch off 10 kΩ or higher



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z22-2 (CA1H) - Body ground Power switch on (IG) Below 1 V
z22-3 (CA1L) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the battery ECU assembly connector.


l.

Install the No. 1 HV battery protector.


m.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

4.CHECK BATTERY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK BATTERY ECU ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A376396C43
1.594,1.406 2.021,1.688 0.427,0.281 2.031,2.188 2.615,1.625 true 2.188,2.198 2.667,1.927 true 1.865,2.198 0.792,1.781 true 0.177,0.063 0.573,0.417 0.396,0.354 10 false *a 1.708,1.458 2.104,1.813 0.396,0.354 10 false z22 2.677,1.531 3.073,1.885 0.396,0.354 10 false CA1L 0.479,1.688 0.875,2.042 0.396,0.354 10 false GND 2.74,1.833 3.135,2.188 0.396,0.354 10 false CA1H
*a Rear view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z22-2 (CA1H) - z22-4 (GND) Power switch on (IG) 2.5 to 3.5 V
z22-3 (CA1L) - z22-4 (GND) Power switch on (IG) 1.5 to 2.5 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z22-2 (CA1H) - z22-3 (CA1L) Power switch off 108 to 132 Ω


HINT:

The resistance will be 2.0 kΩ or less if there is an internal short in the battery ECU assembly.



j.

Reconnect the battery ECU assembly connector.


k.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG