Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404410 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) D

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  DTC CHECK / CLEAR  


CHECK FOR DTCS


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / HV battery / Trouble Codes.

Powertrain > HV Battery > Trouble Codes
50001 398

e.

Check the DTCs and freeze frame data, and then write them down.


f.

Check the details of the DTCs.

HINT:
Display Item Description
Test Failed Shows the malfunction judgment results during the current trip.
Pending Shows the malfunction judgment results up to now (Indicates the possibility of a malfunction when no DTC is confirmed.)
Confirmed Shows the DTCs confirmed up to now (The number of current trips differs for each DTC.)


·

A pending DTC is a DTC that is stored in the battery ECU assembly during the 1st trip when the 2 trip detection logic is used.

·

Freeze frame data is stored for each of the latest result DTCs, pending DTCs and confirmed DTCs.


i.

Enter the following menus: Powertrain / HV Battery / Utility / Check Mode.

Powertrain > HV Battery > Utility
Tester Display
Check Mode
50005 398 1001

ii.

Check items on the display and press "Next".

NOTICE:
·

All the stored DTCs and freeze frame data are cleared if the battery ECU assembly is changed from normal mode to check mode. Before changing modes, always check and note any DTCs and freeze frame data.

·

Changing from normal mode to check mode function is not available when the power switch is turned on (READY).

·

If a DTC is stored, check and note the DTC and freeze frame data following the GTS display, then change from normal mode to check mode.






CHECK FREEZE FRAME DATA


a.

If a DTC is present, select it in order to display its freeze frame data.


b.

Read the freeze frame data recorded when the DTC was stored.



CHECK TIME STAMP


HINT:

By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Health Check.


d.

Perform the following steps when the data setting screen is displayed.


e.

Select the systems for which to perform Health Check and check for time stamp data.

Selectable items:
·

Powertrain

·

Chassis

·

Body

·

Store All Data



f.

Select "Yes" when "Do you want to store time stamp data?" is displayed.

HINT:

If "Yes" is not selected, time stamp data will not be stored.



g.

After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.


h.

Select the desired system from the drop-down list on the bottom of the Time Stamp screen.


i.

Check the order and time which DTCs were stored for the selected system.



CHECK FOR DTCS (SYSTEMS EXCEPT BATTERY ECU ASSEMBLY)


HINT:

The battery ECU assembly maintains communication with other computers, including the motor generator control ECU, the ECM, and hybrid vehicle control ECU. Therefore, if the battery ECU assembly outputs a warning, it is necessary to check and record the DTCs of all systems.


a.

If DTCs are present, check the relevant systems.

HINT:

If DTCs for the CAN communication system are present in addition to other DTCs, first troubleshoot and repair any malfunctions in the CAN communication system.




CLEAR DTCS


NOTICE:

Clearing the DTCs will also clear the freeze frame data.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / HV battery / Trouble Codes.

Powertrain > HV Battery > Trouble Codes
50001 398

e.

Clear DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398