Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404410 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0C3000  Hybrid/EV Battery State of Charge High  


DESCRIPTION

The battery ECU assembly monitors the operation of the hybrid battery system and will store this DTC if it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C3000 Hybrid/EV Battery State of Charge High Even though charging of the HV battery is prohibited due to the SOC reaching the upper limit, charging continues to be performed due to a hybrid control system malfunction.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

HV battery junction block assembly


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0C3000
·

Hybrid Battery SOC

·

WIN Control Limit Power

·

Hybrid Battery Current



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.


HINT:

When the electric parking brake switch assembly is pulled 2 times (2 lock operations), the maximum amount of braking force is applied.


7.

Turn the power switch on (READY), drive (D) selected and the vehicle stopped, firmly depress the brake pedal and accelerator pedal. The engine rpm will increase as well as the value of Data List item "Hybrid Battery SOC". If the value drops, release the accelerator pedal and then depress it again to continue charging.

8.

Check that charging stops when the Data List item "Hybrid Battery SOC" reaches the upper limit.

9.

Enter the following menus: Powertrain / HV battery / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P0C3000" only is output. A
DTCs except "P0C3000" of hybrid battery system are output. B
DTCs except "P0C3000" of hybrid control system are output. C



e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA (HV BATTERY)

B

C

2.CHECK FREEZE FRAME DATA (HV BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Trouble Codes.


d.

Read the freeze frame data of DTC P0C3000.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
OFF is displayed for "Ready Signal", "SMRP Control Status", "SMRB Control Status" and "SMRG Control Status" and -0.5 A or less is displayed for "Hybrid Battery Current". A
Other than above B


HINT:

As the power switch on (IG) state may cause the DTC to be stored, freeze frame data is used to judge the cause of the DTC output.



e.

Turn the power switch off.



A

3.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP, SMRB, SMRG)

B

3.INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP, SMRB, SMRG)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (IG), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the high voltage cable connectors from the HV battery junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

A440115C03
3.229,0.125 3.594,0.375 0.365,0.25 5.615,0.188 6.01,0.406 0.396,0.219 3.406,0.667 3.719,0.406 true 5.813,0.698 6.292,1.063 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.302,0.167 3.563,0.313 0.26,0.146 10 true T3 3.781,0.313 4.24,0.51 0.458,0.198 10 false CBI 5.667,0.208 5.948,0.385 0.281,0.177 10 true z24 6.375,1.031 6.531,1.229 0.156,0.198 10 false +
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance (SMRB):
Tester Connection Condition Specified Condition
T3-1 (CBI) - z24-1 (+) Power switch off 10 kΩ or higher



e.

Measure the resistance according to the value(s) in the table below.

A440115C04
2.219,0.104 2.583,0.344 0.365,0.24 1.167,0.115 1.583,0.354 0.417,0.24 2.063,1.063 2.396,0.677 true 0.833,0.854 1.344,0.656 true 0.271,0.094 0.594,0.531 0.323,0.438 10 false *a 2.281,0.156 2.552,0.313 0.271,0.156 10 true T2 1.229,0.135 1.542,0.313 0.313,0.177 10 true z19 1.813,1 2.188,1.208 0.375,0.208 10 false CEI 0.719,0.781 0.875,0.979 0.156,0.198 10 false -
*a Component without harness connected
(HV Battery Junction Block Assembly)
- -


Standard Resistance (SMRG, SMRP):
Tester Connection Condition Specified Condition
T2-1 (CEI) - z19-1 (-) Power switch off 10 kΩ or higher



f.

Reconnect the high voltage cable connectors to the HV battery junction block assembly.


g.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

4.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NG

4.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Perform a road test.

NOTICE:

Accelerate/decelerate gently. Avoid rapid acceleration/deceleration.



d.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Current

Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Current
50003 398 289

e.

Drive the vehicle with the value of Data List item "Hybrid Battery Current" between -50 A to 50 A.

HINT:

Distance and driving time are not specified.



f.

Turn the power switch off and leave the vehicle for 30 seconds or more.


g.

Turn the power switch on (IG).


h.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Current

Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Current
50003 398 289

i.

Check that the value of "Hybrid Battery Current" is between - 0.5 A and 0.5 A with the power switch on (IG).

NOTICE:
·

If the value is outside the specified range, perform the road test again.

·

This DTC may be output if Current Sensor Offset Learning has not been completed.



HINT:
·

If the power switch is on (IG) and value of "Hybrid Battery Current" is between - 0.5 A and 0.5 A, current sensor offset learning has been completed.

·

Even if the current sensor offset learning is not complete, the current sensor value will be corrected by repeating the road test a maximum of 7 times.




j.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

END