Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P310715  Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open  


DESCRIPTION

Refer to the description for DTC P310711.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>P310711

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P310715 Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open Open or short to +B in the communication circuit
Communication from the airbag sensor assembly stopped and Circuit High has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning: Comes on

Related Data List
DTC No. Data List
P310715 Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 15 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>P310711

Result:
Result Proceed to
The waveform appears as shown in the illustration A
The waveform differs from the one shown in the illustration B



A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P310715 is not output A
P310715 is output again B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)
a.
A439166C01
0.083,0.083 0.396,0.24 0.313,0.156 10 false *a
*a Component with harness connected
(Airbag Sensor Assembly)


Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.

OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the airbag sensor assembly connector.


c.

Turn the power switch on (IG).


d.
A409134C09
0.438,3.25 0.875,3.531 0.438,0.281 1.521,0.146 1.958,0.427 0.438,0.281 1.51,1.938 1.021,1.417 true 2.24,4.177 1.823,3.5 true 0.156,0.177 0.469,0.333 0.313,0.156 10 false *a 0.156,2.208 0.469,2.365 0.313,0.156 10 false *b 2.292,4.219 2.906,4.417 0.615,0.198 10 false GSW2 1.594,1.906 2.208,2.104 0.615,0.198 10 false ABFS 0.51,3.323 1.125,3.521 0.615,0.198 10 false F150 1.604,0.208 2.219,0.406 0.615,0.198 10 false F161
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F161-29 (ABFS) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connectors and the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F161-29 (ABFS) - F150-24 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F161-29 (ABFS) or F150-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the airbag sensor assembly connector.


h.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect the F150 airbag sensor assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

A409147C89
5.26,0.219 5.646,0.479 0.385,0.26 5.729,2.396 6.021,1.49 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 5.313,0.281 5.948,0.531 0.635,0.25 10 false F161 5.563,2.448 6.198,2.698 0.635,0.25 10 false ABFS
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


NOTICE:

Turning the power switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.


Standard Voltage:
Tester Connection Condition Specified Condition
F161-29 (ABFS) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the F150 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BODY GROUND)
a.

Disconnect the airbag sensor assembly connector.


b.
A412317C16
0.385,0.875 0.854,1.188 0.469,0.313 2.552,1.573 1.823,1.438 true 0.469,0.938 0.927,1.135 0.458,0.198 10 false F150 2.635,1.542 3.094,1.74 0.458,0.198 10 false E1 0.167,0.115 0.625,0.313 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
F150-33 (E1) - Body ground Power switch off Below 1 Ω



c.

Reconnect the airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR