Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A1B94  Drive Motor "A" Control Module Unexpected Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The hybrid vehicle control ECU monitors the motor generator control ECU (MG ECU).

The cause of this malfunction may be the following:

Motor generator control ECU internal malfunction
·

Motor generator control ECU (MG ECU) malfunction



DESCRIPTION

The hybrid vehicle control ECU monitors the motor generator control ECU (MG ECU) and stores this DTC when it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A1B94 Drive Motor "A" Control Module Unexpected Operation The motor generator control ECU (MG ECU) value received by the hybrid vehicle control ECU exceeds the threshold for a certain period of time.
(1 trip detection logic)
·

Inverter with converter assembly

·

Fusible link block assembly (MAIN NO. 2)

·

IGCT relay


Comes on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

HINT:

If the vehicle has returned to normal, it can be driven after turning the power switch on (READY).


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A404776E18
0.531,1.948 0.99,2.146 0.458,0.198 10 false M112 0.906,3.375 2,3.552 1.094,0.177 10 false Auxiliary Battery 0.385,1.948 0.563,2.115 0.177,0.167 10 false 1 0.385,2.656 0.563,2.823 0.177,0.167 10 false 1 0.635,2.656 1.135,2.854 0.5,0.198 10 false A 2.01,1.917 2.438,2.125 0.427,0.208 10 false IGCT 2.458,1.531 2.635,1.698 0.177,0.167 10 false 1 1.75,1.531 1.927,1.698 0.177,0.167 10 false 2 2.469,1.135 2.646,1.302 0.177,0.167 10 false 5 1.74,1.135 1.917,1.302 0.177,0.167 10 false 3 4.063,1.385 4.698,1.583 0.635,0.198 10 false PM-IGCT 4.063,1.135 4.24,1.302 0.177,0.167 10 false 1 4.542,1.125 4.719,1.292 0.177,0.167 10 false 2 4.052,3.042 4.229,3.208 0.177,0.167 10 false 1 4.521,3.042 4.698,3.208 0.177,0.167 10 false 2 4,3.302 4.781,3.5 0.781,0.198 10 false IGCT NO. 2 5.729,0.76 6.094,0.948 0.365,0.188 10 false +B1 5.719,1.229 6.083,1.417 0.365,0.188 10 false +B2 5.719,1.625 6.167,1.813 0.448,0.188 10 false MREL 5.719,1.99 6.167,2.177 0.448,0.188 10 false E1 5.729,3.615 6.188,3.792 0.458,0.177 10 false GND1 5.729,3.146 6.188,3.323 0.458,0.177 10 false IGCT 5.448,3.042 5.708,3.25 0.26,0.208 10 false 12 5.469,3.51 5.729,3.719 0.26,0.208 10 false 24 5.604,3.958 5.958,4.146 0.354,0.188 10 false C98 5.604,4.115 7,4.5 1.396,0.385 10 false Inverter with Converter Assembly 5.302,2.438 7.031,2.625 1.729,0.188 10 false Hybrid Vehicle Control ECU 5.354,0.771 5.719,0.958 0.365,0.188 10 false A97 5.333,1.24 5.698,1.427 0.365,0.188 10 false F161 5.365,1.635 5.729,1.823 0.365,0.188 10 false A97 5.323,2.01 5.688,2.198 0.365,0.188 10 false F161 5.396,0.563 5.646,0.75 0.25,0.188 10 false 11 5.438,1.01 5.688,1.198 0.25,0.188 10 false 1 5.448,1.448 5.698,1.635 0.25,0.188 10 false 5 5.448,1.823 5.698,2.01 0.25,0.188 10 false 3 0.938,2.229 2.74,2.604 1.802,0.375 10 false Fusible Link Block Assembly (MAIN NO. 2) 0.604,4.479 1.104,4.677 0.5,0.198 10 false tA

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the negative (-) and positive (+) auxiliary battery terminals.

OK:

The terminals are connected securely and there is no contact problem.


HINT:

If performing a reproduction test, turn the power switch on (IG) and shake the wire harnesses vertically and horizontally before checking for DTCs.



Result:
Proceed to
OK
NG



OK

2.CHECK GROUND WIRE CONNECTION CONDITION

NG

6.CONNECT SECURELY
2.CHECK GROUND WIRE CONNECTION CONDITION
a.
A452311

Check the installation condition of the ground wire tA.

OK:

The ground wire tA is securely installed.


HINT:

If performing a reproduction test, turn the power switch on (IG) and shake the wire harnesses vertically and horizontally before checking for DTCs.



Result:
Proceed to
OK
NG



OK

3.CHECK FUSIBLE LINK (MAIN NO. 2)

NG

7.CONNECT SECURELY
3.CHECK FUSIBLE LINK (MAIN NO. 2)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A452312C01
1.75,1.521 2.188,1.719 0.438,0.198 0.969,1.083 1.229,1.281 0.26,0.198 1.823,0.917 2.042,0.5 2.042,0.5 2.177,0.5 true 1.771,1.542 2.167,1.708 0.396,0.167 10 true M112 1.01,1.104 1.188,1.271 0.177,0.167 10 true A 2.229,0.417 2.448,0.594 0.219,0.177 10 true *1
*1 Fusible Link Block Assembly


Check the fusible link block assembly (MAIN NO. 2) for improper installation.

OK:

The fusible link block assembly is installed securely and there is no contact problem.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M112-1 - A-1 (Positive (+) auxiliary battery terminal) Power switch off Below 1 Ω



d.

Reconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

4.CHECK RELAY (IGCT)

NG

8.REPAIR OR REPLACE MALFUNCTIONING PARTS
4.CHECK RELAY (IGCT)
a.

Check the IGCT relay for improper installation.

OK:

The relay is installed securely.


HINT:

If performing a reproduction test, turn the power switch on (IG) and gently vibrate the IGCT relay with a finger before checking for DTCs.



b.
A439171C01
2.781,2.896 2.167,2.26 true 0.281,0.167 0.594,0.323 0.313,0.156 10 false *1 2.854,2.927 3.167,3.083 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT Relay


Remove the IGCT relay from the No. 5 relay block assembly.


c.
A253297C27
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



d.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

9.REPAIR OR REPLACE MALFUNCTIONING PARTS
5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
HINT:

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
P0A1B94 only is output A
DTCs except P0A1B94 are output B



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

6.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
7.CONNECT SECURELY
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
8.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
9.REPAIR OR REPLACE MALFUNCTIONING PARTS
Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC

NEXT

11.SIMULATION TEST
11.SIMULATION TEST
a.

Turn the power switch off and wait for 2 minutes or more.


b.

Turn the power switch on (IG) and wait for 2 minutes or more.


c.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT (HYBRID CONTROL)
12.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs are output A
P0A1B94 only is output B
DTCs except P0A1B94 are output C



e.

Turn the power switch off.



A

END

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

C