Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM U

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  TERMINALS OF ECU  


HYBRID VEHICLE CONTROL ECU


C338835E22
1.25,0.323 1.667,0.583 0.417,0.26 3.271,0.292 3.688,0.552 0.417,0.26 5.313,0.302 5.729,0.563 0.417,0.26 1.354,0.375 1.813,0.573 0.458,0.198 10 false A97 3.333,0.354 3.792,0.552 0.458,0.198 10 false F160 5.375,0.354 5.833,0.552 0.458,0.198 10 false F161

Terminal No.
(Symbol)
Wiring Color Input/Output Terminal Description Condition Specified Condition
A97-2 (R) - F161-3 (E1) L - W-B IN Shift lever position signal Power switch on (IG), shift lever in R 6 to 14 V
Power switch on (IG), shift lever not in R 0 to 1.5 V
A97-3 (DB1) - F161-3 (E1) W - W-B IN Shift lever position signal Power switch on (IG), shift lever in D or S 6 to 14 V
Power switch on (IG), shift lever not in D or S 0 to 1.5 V
A97-4 (HMCH) - F161-3 (E1) B - W-B IN/OUT Communication signal Power switch on (IG) Pulse generation
(Waveform 1)
A97-5 (MREL) - F161-3 (E1) BE - W-B OUT Main relay Power switch on (IG) 11 to 14 V
A97-6 (HSDN) - F161-3 (E1) B - W-B OUT MG ECU shutdown signal Power switch on (READY) 0 to 1.5 V
A97-7 (STP) - F161-3 (E1) SB - W-B IN Stop light switch Brake pedal depressed 11 to 14 V
Brake pedal released 0 to 1.5 V
A97-8 (LIN3) - F161-3 (E1) Y - W-B IN/OUT LIN communication signal
(A/C inverter, auxiliary battery state sensor)
Power switch on (READY) Pulse generation
A97-11 (+B1) - F161-3 (E1) R - W-B IN Power source Power switch on (IG) 11 to 14 V
A97-13 (DRN5) - Body ground G - Body ground - Shield ground Always Below 1 Ω
A97-14 (HMCL) - F161-3 (E1) W - W-B IN/OUT Communication signal Power switch on (IG) Pulse generation
(Waveform 1)
A97-15 (DB2) - F161-3 (E1) G - W-B IN Shift lever position signal Power switch on (IG), shift lever in D or S 6 to 14 V
Power switch on (IG), shift lever not in D or S 0 to 1.5 V
A97-16 (PR) - F161-3 (E1) V - W-B IN Shift lever position signal Power switch on (IG), shift lever in P or R 6 to 14 V
Power switch on (IG), shift lever not in P or R 0 to 1.5 V
A97-18 (PSFT) - F161-3 (E1) R - W-B OUT Shift lever position sensor power source Power switch on (ACC) 7.5 to 14 V
A97-20 (BL) - F161-3 (E1) LG - W-B OUT Back-up light relay Power switch on (IG), shift lever in R 11 to 14 V
A97-24 (VCPA) - A97-37 (EPA) Y - L OUT Accelerator pedal sensor assembly power source (for VPA) Power switch on (IG) 4.5 to 5.5 V
A97-26 (VCP2) - A97-25 (EPA2) G - W OUT Accelerator pedal sensor assembly power source (for VPA2) Power switch on (IG) 4.5 to 5.5 V
A97-28 (P) - F161-3 (E1) B - W-B IN Shift lever position signal Power switch on (IG), shift lever in P 6 to 14 V
Power switch on (IG), shift lever not in P 0 to 1.5 V
A97-29 (N) - F161-3 (E1) SB - W-B IN Shift lever position signal Power switch on (IG), shift lever in N 6 to 14 V
Power switch on (IG), shift lever not in N 0 to 1.5 V
A97-30 (PNB) - F161-3 (E1) P - W-B IN Shift lever position signal Power switch on (IG), shift lever in P or N 6 to 14 V
A97-33 (NIWP) - F161-3 (E1) P - W-B IN Inverter water pump assembly signal Power switch on (READY) Pulse generation
(Waveform 2)
A97-34 (IWP) - F161-3 (E1) G - W-B OUT Inverter water pump assembly signal Power switch on (READY) Pulse generation
(Waveform 2)
A97-36 (VPA) - A97-37 (EPA) R - L IN Accelerator pedal sensor assembly (for accelerator pedal position detection) Power switch on (IG), accelerator pedal released 0.4 to 1.4 V
Power switch on (IG), engine stopped, shift position P, accelerator pedal fully depressed 2.6 to 4.5 V
A97-38 (VPA2) - A97-25 (EPA2) B - W IN Accelerator pedal sensor assembly (for accelerator pedal sensor malfunction detection) Power switch on (IG), accelerator pedal released 1.0 to 2.2 V
Power switch on (IG), engine stopped, shift position P, accelerator pedal fully depressed 3.4 to 5.3 V
A97-40 (TTA) - A97-39 (ETTA) G - Y IN Transmission fluid temperature sensor Power switch on (IG), temperature 25°C (77°F) 3.6 to 4.6 V
Power switch on (IG), temperature 60°C (140°F) 2.2 to 3.2 V
A97-46 (MMT) - A97-45 (MMTG) L - BR IN Motor temperature sensor Power switch on (IG), temperature 25°C (77°F) 3.6 to 4.6 V
Power switch on (IG), temperature 60°C (140°F) 2.2 to 3.2 V
A97-48 (GMT) - A97-47 (GMTG) B - R IN Generator temperature sensor Power switch on (IG), temperature 25°C (77°F) 3.6 to 4.6 V
Power switch on (IG), temperature 60°C (140°F) 2.2 to 3.2 V
F160-5 (ILK) - F161-3 (E1) V - W-B IN Interlock switch Power switch on (IG), service plug grip installed correctly 0 to 1.5 V
Power switch on (IG), service plug grip not installed 11 to 14 V
F160-7 (CA3P) - F161-3 (E1) R - W-B IN/OUT CAN communication signal Power switch on (IG) Pulse generation
(Waveform 3)
F160-8 (CA1L) - F161-3 (E1) P - W-B IN/OUT CAN communication signal Power switch on (IG) Pulse generation
(Waveform 4)
F160-11 (E02) - Body ground W-B - Body ground - Ground Always Below 1 Ω
F160-12 (E01) - Body ground W-B - Body ground - Ground Always Below 1 Ω
F160-13 (SMRG) - F160-12 (E01) P - W-B OUT System main relay operation signal Power switch on (IG)→Power switch on (READY) Pulse generation
(Waveform 5)
F160-15 (SMRP) - F160-12 (E01) LG - W-B OUT System main relay operation signal Power switch on (IG)→Power switch on (READY) Pulse generation
(Waveform 5)
F160-16 (SMRB) - F160-12 (E01) BE - W-B OUT System main relay operation signal Power switch on (IG)→Power switch on (READY) Pulse generation
(Waveform 5)
F160-20 (CA3N) - F161-3 (E1) W - W-B IN/OUT CAN communication signal Power switch on (IG) Pulse generation
(Waveform 3)
F160-21 (CA1H) - F161-3 (E1) L - W-B IN/OUT CAN communication signal Power switch on (IG) Pulse generation
(Waveform 4)
F160-25 (PLKC) - F161-3 (E1) LG - W-B OUT Shift lock release request signal Power switch on (READY), brake pedal depressed 11 to 14 V
Power switch on (READY), brake pedal released 0 to 1.5 V
F160-28 (ST1-) - F161-3 (E1) R - W-B IN Stop light switch signal Power switch on (IG), brake pedal depressed 0 to 1.5 V
Power switch on (IG), brake pedal released 11 to 14 V
F160-29 (ACCI) - F161-3 (E1) R - W-B IN ACC relay Power switch on (ACC) 11 to 14 V
F160-34 (E12) - Body ground W-B - Body ground - Ground Always Below 1 Ω
F160-35 (IG2) - F161-3 (E1) V - W-B IN Power source Power switch on (IG) 11 to 14 V
F160-38 (SI0) - F161-3 (E1) SB - W-B OUT Battery cooling blower operation signal Battery cooling blower operating Pulse generation
(Waveform 6)
Battery cooling blower not operating 4.5 to 5.5 V
F160-41 (BTH+) - F161-3 (E1) G - W-B IN Communication signal from battery voltage sensor to hybrid vehicle control ECU Power switch on (IG) Pulse generation
(Waveform 7)
F160-42 (BTH-) - F161-3 (E1) W - W-B IN Communication signal from battery voltage sensor to hybrid vehicle control ECU Power switch on (IG) Pulse generation
(Waveform 7)
F161-1 (+B2) - F161-3 (E1) B - W-B IN Power source Power switch on (IG) 11 to 14 V
F161-3 (E1) - Body ground W-B - Body ground - Ground Always Below 1 Ω
F161-4 (ST2) - F161-3 (E1) B - W-B IN Starter signal Power switch on (IG) 0 to 1.5 V
F161-7 (INDR) - F161-3 (E1) R - W-B IN Shift position indicator signal Power switch on (IG), shift lever in R 0 to 3.2 V
Power switch on (IG), shift lever not in R 11 to 14 V
F161-8 (INDD) - F161-3 (E1) V - W-B IN Shift position indicator signal Power switch on (IG), shift lever in D 0 to 3.2 V
Power switch on (IG), shift lever not in D 11 to 14 V
F161-11 (SFTD) - F161-3 (E1) R - W-B IN Transmission control Power switch on (IG), shift lever in S 11 to 14 V
Power switch on (IG), shift lever in (-) or shift paddle switch LH (-) operated 0 to 1.5 V
F161-19 (INDP) - F161-3 (E1) G - W-B IN Shift position indicator signal Power switch on (IG), shift lever in P 0 to 3.2 V
Power switch on (IG), shift lever not in P 11 to 14 V
F161-20 (INDM) - F161-3 (E1) B - W-B IN Shift position indicator signal Power switch on (IG), shift lever in S 0 to 3.2 V
Power switch on (IG), shift lever not in S 11 to 14 V
F161-21 (INDN) - F161-3 (E1) GR - W-B IN Shift position indicator signal Power switch on (IG), shift lever in N 0 to 3.2 V
Power switch on (IG), shift lever not in N 11 to 14 V
F161-24 (SFTU) - F161-3 (E1) B - W-B IN Transmission control Power switch on (IG), shift lever in S 11 to 14 V
Power switch on (IG), shift lever in (+) or shift paddle switch RH (+) operated 0 to 1.5 V
F161-25 (M) - F161-3 (E1) W - W-B IN Transmission control Power switch on (IG), shift lever in S 11 to 14 V
Power switch on (IG), shift lever not in S 0 to 1.5 V
F161-27 (BATT) - F161-3 (E1) Y - W-B*1
B - W-B*2
IN Constant power source Always 10 to 14 V
F161-29 (ABFS) - F161-3 (E1) B - W-B IN Airbag activation signal Power switch on (READY) Pulse generation
(Waveform 8)
F161-33 (EVSW) - F161-3 (E1) R - W-B IN EV drive mode switch (combination switch assembly) signal Power switch on (IG), EV drive mode switch not pushed 11 to 14 V
Power switch on (IG), EV drive mode switch pushed and held 0 to 1.5 V
F161-44 (IGB) - F161-3 (E1) V - W-B IN Power source Power switch on (IG) 11 to 14 V

*1: for LHD

*2: for RHD

a.

Oscilloscope waveforms

HINT:

Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


i.
A284438E06
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 1 (Communication signal)

Item Content
Terminal CH1: A97-4 (HMCH) - F161-3 (E1)
CH2: A97-14 (HMCL) - F161-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Power switch on (IG)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



ii.
A415999E04
0.365,0.854 0.823,1.052 0.458,0.198 10 false CH1 0.375,1.417 0.833,1.615 0.458,0.198 10 false CH2 2.958,1.635 3.281,1.917 0.323,0.281 10 false GND 2.958,0.854 3.281,1.135 0.323,0.281 10 false GND

Waveform 2 (Inverter water pump assembly signal)

Item Content
Terminal CH1: A97-34 (IWP) - F161-3 (E1)
CH2: A97-33 (NIWP) - F161-3 (E1)
Equipment Setting 5 V/DIV., 20 ms./DIV.
Condition Power switch on (READY)

HINT:

The duty of the IWP signal and the frequency of the NIWP signal change according to the coolant (for inverter) temperature.



iii.
A284438E07
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 3 (CAN communication signal)

Item Content
Terminal CH1: F160-7 (CA3P) - F161-3 (E1)
CH2: F160-20 (CA3N) - F161-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Power switch on (IG)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



iv.
A284438E06
2.969,1.198 3.427,1.396 0.458,0.198 10 GND 2.969,1.573 3.427,1.771 0.458,0.198 10 GND 0.396,0.646 0.854,0.844 0.458,0.198 10 CH1 0.396,1.229 0.854,1.427 0.458,0.198 10 CH2

Waveform 4 (CAN communication signal)

Item Content
Terminal CH1: F160-21 (CA1H) - F161-3 (E1)
CH2: F160-8 (CA1L) - F161-3 (E1)
Equipment Setting 1 V/DIV., 50 μs./DIV.
Condition Power switch on (IG)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



v.
C206010E10
2.958,0.656 3.292,0.896 0.333,0.24 10 false GND 2.958,1.042 3.292,1.281 0.333,0.24 10 false GND 2.958,1.427 3.292,1.667 0.333,0.24 10 false GND 0.271,0.573 0.594,0.781 0.323,0.208 10 false CH1 0.281,0.948 0.615,1.188 0.333,0.24 10 false CH2 0.292,1.313 0.625,1.552 0.333,0.24 10 false CH3

Waveform 5 (System main relay operation signal)

Item Content
Terminal CH1: F160-15 (SMRP) - F160-12 (E01)
CH2: F160-16 (SMRB) - F160-12 (E01)
CH3: F160-13 (SMRG) - F160-12 (E01)
Equipment Setting 10 V/DIV., 200 ms./DIV.
Condition Power switch on (IG) → Power switch on (READY)


vi.
C257882E01
2.99,1.052 3.396,1.292 0.406,0.24 10 false GND

Waveform 6 (HV battery blower fan operation signal)

Item Content
Terminal F160-38 (SI0) - F161-3 (E1)
Equipment Setting 10 V/DIV., 1 ms./DIV.
Condition Cooling fans operating

HINT:

The waveform will vary with the operating speed of the battery cooling blower assembly.



vii.
A298837E01
0.313,0.771 0.635,0.948 0.323,0.177 10 CH1 0.323,1.354 0.646,1.531 0.323,0.177 10 CH2 2.99,1.042 3.354,1.24 0.365,0.198 10 GND 2.99,1.594 3.354,1.792 0.365,0.198 10 GND

Waveform 7 (Communication signal from battery voltage sensor to hybrid vehicle control ECU)

Item Content
Terminal CH1: F160-41 (BTH+) - F161-3 (E1)
CH2: F160-42 (BTH-) - F161-3 (E1)
Equipment Setting 2 V/DIV., 500 μs./DIV.
Condition Power switch on (IG)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



viii.
A298836E01
3.01,1.052 3.396,1.25 0.385,0.198 10 GND

Waveform 8 (Airbag activation signal)

Item Content
Terminal F161-29 (ABFS) - F161-3 (E1)
Equipment Setting 5 V/DIV., 125 ms./DIV.
Condition Power switch on (READY)




BATTERY VOLTAGE SENSOR


A368663E10
1.469,3.031 1.896,3.26 0.427,0.229 4.656,3.031 5.083,3.26 0.427,0.229 5.875,3.021 6.302,3.25 0.427,0.229 1.615,3.063 1.927,3.26 0.313,0.198 10 false z8 4.771,3.073 5.313,3.229 0.542,0.156 10 false z12 5.958,3.052 6.302,3.229 0.344,0.177 10 false M41

Terminal No.
(Symbol)
Wiring Color Terminal Description Input/Output Condition Specified Condition
z12-1 (TC0) - z12-7 (GC0) G - G Intake air temperature sensor Input Power switch on (IG), HV battery intake air temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-2 (TB2) - z12-8 (GB2) R - R Battery temperature sensor 2 Input Power switch on (IG), HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-3 (TB1) - z12-9 (GB1) W - W Battery temperature sensor 1 Input Power switch on (IG), HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-4 (TB0) - z12-10 (GB0) L - L Battery temperature sensor 0 Input HV battery temperature: -40 to 90°C (-40 to 194°F) 4.8 (-40°C (-40°F)) to 1.0 V (90°C (194°F))
z12-5 (IB0) - z12-12 (GIB) Y - B Battery current sensor Input Power switch on (READY) 0.5 to 4.5 V
z12-6 (VIB) - z12-12 (GIB) BR - B Power source for battery current sensor Output Power switch on (IG) 4.5 to 5.5 V
M41-1 (IGCT) - M41-5 (GND) BR - W-B Control signal Input Power switch on (READY) 11 to 15.5 V
M41-2 (BTH+) - M41-5 (GND) R - W-B Serial communication Output Power switch on (IG) Pulse generation
(waveform 1)
M41-3 (BTH-) - M41-5 (GND) W - W-B Serial communication Output Power switch on (IG) Pulse generation
(waveform 2)
M41-5 (GND) - Body ground W-B - Body ground Ground - Always (continuity check) Below 1 Ω
M41-8 (FP0) - M41-5 (GND) B - W-B Battery cooling blower No. 0 monitor signal Input Battery cooling blower stopped 0 Hz
Battery cooling blower activated Pulse generation
(waveform 3)

a.

Oscilloscope waveforms

HINT:

Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.


i.
A284561E09
2.99,1.219 3.396,1.417 0.406,0.198 10 GND

Waveform 1 (Serial communication)

Item Content
Terminal M41-2 (BTH+) - M41-5 (GND)
Equipment Setting 2 V/DIV., 500 μs/DIV.
Condition Power switch on (IG)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



ii.
A284562E08
2.99,1.229 3.396,1.438 0.406,0.208 10 GND

Waveform 2 (Serial communication)

Item Content
Terminal M41-3 (BTH-) - M41-5 (GND)
Equipment Setting 2 V/DIV., 500 μs/DIV.
Condition Power switch on (IG)

HINT:

The waveform will vary depending on the content of the digital communication (digital signal).



iii.
A284436E08
2.938,1.031 3.396,1.229 0.458,0.198 10 false GND

Waveform 3 (Battery cooling blower No. 0 monitor signal)

Item Content
Terminal M41-8 (FP0) - M41-5 (GND)
Equipment Setting 2 V/DIV., 2 ms/DIV.
Condition Battery cooling blower assembly (No. 0) operating (Active Test of cooling fan being performed)

HINT:

The frequency of the waveform will vary with the operating speed of the battery cooling blower assembly (No. 0).