Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM J

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

If the power switch is on (IG), the hybrid vehicle control ECU applies current to the MREL terminal to turn the IGCT relay on. This supplies power to the +B1 and +B2 terminals.

WIRING DIAGRAM

A443437E02
0.063,2.656 0.99,3.125 0.927,0.469 10 false from Auxiliary Battery 2.854,1.917 4.729,2.125 1.875,0.208 10 false No. 5 Relay Block Assembly 3.24,1.583 3.625,1.771 0.385,0.188 10 false IGCT 2.969,0.708 3.125,0.906 0.156,0.198 10 false 3 2.938,1.125 3.094,1.323 0.156,0.198 10 false 2 1.052,0.969 1.979,1.167 0.927,0.198 10 false MAIN NO. 2 3.729,1.125 3.885,1.323 0.156,0.198 10 false 1 3.729,0.708 3.885,0.906 0.156,0.198 10 false 5 3.969,0.708 4.125,0.906 0.156,0.198 10 false 1 4.354,0.708 4.51,0.906 0.156,0.198 10 false 2 3.906,0.99 4.531,1.177 0.625,0.188 10 false PM-IGCT 5.979,0.375 6.438,0.573 0.458,0.198 10 false +B1 5.625,0.375 5.906,0.563 0.281,0.188 10 false A97 5.656,0.188 5.917,0.458 0.26,0.271 10 false 11 5.594,0.813 5.969,0.979 0.375,0.167 10 false F161 5.625,1.24 5.906,1.427 0.281,0.188 10 false A97 5.698,0.615 5.854,0.813 0.156,0.198 10 false 1 5.698,1.042 5.854,1.24 0.156,0.198 10 false 5 5.427,3.354 7.156,3.708 1.729,0.354 10 false Hybrid Vehicle Control ECU 5.979,0.802 6.438,1 0.458,0.198 10 false +B2 5.979,1.229 6.594,1.427 0.615,0.198 10 false MREL 5.594,1.667 5.938,1.844 0.344,0.177 10 false F160 5.594,2.948 5.938,3.167 0.344,0.219 10 false F161 5.667,1.469 5.875,1.688 0.208,0.219 10 false 34 5.667,1.906 5.875,2.177 0.208,0.271 10 false 12 5.667,2.333 5.875,2.563 0.208,0.229 10 false 11 5.698,2.75 5.854,2.948 0.156,0.198 10 false 3 5.99,1.656 6.344,1.844 0.354,0.188 10 false E12 5.99,2.083 6.344,2.271 0.354,0.188 10 false E01 5.99,2.521 6.344,2.708 0.354,0.188 10 false E02 5.979,2.948 6.333,3.135 0.354,0.188 10 false E1 0.896,1.917 2.094,2.344 1.198,0.427 10 false Fusible Link Block Assembly 1.865,0.813 2.323,1.052 0.458,0.24 10 false M112 2,0.594 2.156,0.792 0.156,0.198 10 false 1 0.781,0.604 0.938,0.802 0.156,0.198 10 false 1 0.771,0.813 0.927,1.01 0.156,0.198 10 false A 5.604,2.094 5.948,2.271 0.344,0.177 10 false F160 5.594,2.521 5.938,2.698 0.344,0.177 10 false F160

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK HYBRID VEHICLE CONTROL ECU (+B1, +B2 VOLTAGE)
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

A409147C93
5.24,0.25 5.667,0.552 0.427,0.302 1.49,0.25 1.917,0.552 0.427,0.302 5.833,2.25 6.25,1.281 true 0.771,2.25 1.188,1.25 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 5.302,0.323 5.938,0.573 0.635,0.25 10 false F161 5.615,2.354 6.25,2.604 0.635,0.25 10 false +B2 1.583,0.333 2.219,0.583 0.635,0.25 10 false A97 0.615,2.333 1.25,2.583 0.635,0.25 10 false +B1
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A97-11 (+B1) - Body ground Power switch on (IG) 11 to 14 V
F161-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)

NG

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)
2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BODY GROUND)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

A368649C34
3.583,0.729 4,0.958 0.417,0.229 0.385,0.74 0.802,0.969 0.417,0.229 4.698,0.802 4.979,0.24 true 2.365,1.479 2.594,1.115 true 2.771,0.844 2.927,0.323 true 2.656,0.844 2.365,0.292 true 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 0.427,0.771 0.854,0.938 0.427,0.167 10 false F160 3.635,0.771 4,0.948 0.365,0.177 10 false F161 5.042,0.094 5.354,0.25 0.313,0.156 10 false E1 2.167,1.5 2.479,1.656 0.313,0.156 10 false E12 2.938,0.146 3.25,0.302 0.313,0.156 10 false E01 2.104,0.146 2.417,0.302 0.313,0.156 10 false E02
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F161-3 (E1) - Body ground Always Below 1 Ω
F160-12 (E01) - Body ground Always Below 1 Ω
F160-11 (E02) - Body ground Always Below 1 Ω
F160-34 (E12) - Body ground Always Below 1 Ω



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID VEHICLE CONTROL ECU (MREL VOLTAGE)
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

A409147C94
1.49,0.25 1.917,0.552 0.427,0.302 1.229,2.25 1.917,1.271 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 1.583,0.333 2.219,0.583 0.635,0.25 10 false A97 1.021,2.333 1.656,2.583 0.635,0.25 10 false MREL
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A97-5 (MREL) - Body ground Power switch on (IG) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

4.CHECK FUSE (PM-IGCT)

NG

4.CHECK FUSE (PM-IGCT)
a.
A435209C01
1.969,1.177 2.521,0.885 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *1 2.573,0.771 2.885,0.927 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 PM-IGCT Fuse


Remove the PM-IGCT fuse from the No. 5 relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PM-IGCT fuse Always Below 1 Ω



c.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

5.CHECK FUSE (IGCT IG)

NG

11.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
5.CHECK FUSE (IGCT IG)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A452312C01
1.75,1.521 2.188,1.719 0.438,0.198 0.969,1.083 1.229,1.281 0.26,0.198 1.823,0.917 2.042,0.5 2.042,0.5 2.177,0.5 true 1.771,1.542 2.167,1.708 0.396,0.167 10 true M112 1.01,1.104 1.188,1.271 0.177,0.167 10 true A 2.229,0.417 2.448,0.594 0.219,0.177 10 true *1
*1 Fusible Link Block Assembly


Check the fusible link block assembly (IGCT IG) for improper installation.

OK:

The fusible link block assembly is installed securely and there is no contact problem.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (Fusible Link Block Assembly) - M112-1 (Fusible Link Block Assembly) Always Below 1 Ω



d.

Reconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

6.INSPECT RELAY (IGCT)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY)
6.INSPECT RELAY (IGCT)
a.
A439171C01
2.781,2.896 2.167,2.26 true 0.281,0.167 0.594,0.323 0.313,0.156 10 false *1 2.854,2.927 3.167,3.083 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT Relay


Remove the IGCT relay from the No. 5 relay block assembly.


b.
A253297C01
0.146,0.056 0.409,0.261 0.263,0.205 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

NG

REPLACE RELAY (IGCT)

7.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Remove the PM-IGCT fuse from the No. 5 relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

A434282C05
3.5,0.521 3.917,0.771 0.417,0.25 5.833,0.5 6.25,0.75 0.417,0.25 5.417,0.74 5.167,1.417 true 4.583,0.75 4.26,1.406 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *1 2.063,0.646 2.375,0.802 0.313,0.156 10 false *b 2.854,0.177 3.167,0.333 0.313,0.156 10 false *a 4.635,0.646 5,0.833 0.365,0.188 10 false +B1 5.469,0.646 5.833,0.833 0.365,0.188 10 false +B2 3.594,0.573 3.927,0.823 0.333,0.25 10 false A97 5.885,0.542 6.25,0.708 0.365,0.167 10 false F161
*1 No. 5 Relay Block Assembly - -
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b PM-IGCT Fuse Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A97-11 (+B1) - 2 (PM-IGCT fuse holder) Always Below 1 Ω
F161-1 (+B2) - 2 (PM-IGCT fuse holder) Always Below 1 Ω



d.

Install the PM-IGCT fuse.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - FUSIBLE LINK BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - FUSIBLE LINK BLOCK ASSEMBLY)
a.

Disconnect the PM-IGCT Fuse, IGCT relay from the No. 5 relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

A452329C01
5.208,1.76 5.677,2.021 0.469,0.26 5.313,1.292 5.802,0.448 true 0.188,0.167 0.406,0.354 0.219,0.188 10 false *1 2.292,0.469 2.51,0.656 0.219,0.188 10 false *a 1.188,1.948 1.406,2.135 0.219,0.188 10 false *b 5.813,0.271 6.052,0.448 0.24,0.177 10 false *2 5.24,1.781 5.656,1.979 0.417,0.198 10 true M112
*1 No. 5 Relay Block Assembly *2 Fusible Link Block Assembly
*a PM-IGCT Fuse Holder *b IGCT Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay holder) - M112-1 (Fusible Link Block Assembly) Always Below 1 Ω
5 (IGCT relay holder) - 1 (PM-IGCT fuse holder) Always Below 1 Ω



c.

Install the PM-IGCT fuse and IGCT relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 5 RELAY BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 5 RELAY BLOCK ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Remove the IGCT relay from the No. 5 relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

A436002C03
3.594,1.219 4,1.51 0.406,0.292 4.927,1.344 5.281,0.625 true 0.646,0.188 0.958,0.344 0.313,0.156 10 false *1 1.635,1.979 1.948,2.135 0.313,0.156 10 false *b 3.76,0.208 4.073,0.365 0.313,0.156 10 false *a 5.344,0.469 5.969,0.698 0.625,0.229 10 false MREL 3.688,1.292 4.313,1.521 0.625,0.229 10 false A97
*1 No. 5 Relay Block Assembly - -
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b IGCT Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A97-5 (MREL) - 1 (IGCT relay holder) Always Below 1 Ω
A97-5 (MREL) or 1 (IGCT relay holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Install the IGCT relay.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - BODY GROUND)
a.

Remove the IGCT relay from the No. 5 relay block assembly.


b.
A435204C05
0.146,0.188 0.458,0.385 0.313,0.198 10 false *1 1.563,3.115 1.875,3.313 0.313,0.198 10 false *a
*1 No. 5 Relay Block Assembly
*a IGCT Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (IGCT relay holder) - Body ground Always Below 1 Ω



c.

Install the IGCT relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Remove the PM-IGCT fuse from the No. 5 relay block assembly.


b.

Disconnect the hybrid vehicle control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

A434282C06
3.5,0.521 3.917,0.771 0.417,0.25 5.833,0.5 6.25,0.75 0.417,0.25 5.417,0.74 5.167,1.417 true 4.583,0.75 4.26,1.406 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *1 2.042,0.667 2.354,0.823 0.313,0.156 10 false *b 2.854,0.177 3.167,0.333 0.313,0.156 10 false *a 4.635,0.646 5,0.833 0.365,0.188 10 false +B1 5.469,0.646 5.833,0.833 0.365,0.188 10 false +B2 3.594,0.573 3.927,0.823 0.333,0.25 10 false A97 5.885,0.552 6.25,0.719 0.365,0.167 10 false F161
*1 No. 5 Relay Block Assembly - -
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b PM-IGCT Fuse Holder


Standard Resistance:
Tester Connection Condition Specified Condition
A97-11 (+B1) or 2 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher
F161-1 (+B2) or 2 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU connectors.


e.

Install the PM-IGCT fuse.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (PM-IGCT)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (NO. 5 RELAY BLOCK ASSEMBLY)
a.

Disconnect the PM-IGCT Fuse and IGCT relay from the No. 5 relay block assembly.

A452329C01
5.208,1.76 5.677,2.021 0.469,0.26 5.313,1.292 5.802,0.448 true 0.188,0.167 0.406,0.354 0.219,0.188 10 false *1 2.292,0.469 2.51,0.656 0.219,0.188 10 false *a 1.188,1.948 1.406,2.135 0.219,0.188 10 false *b 5.813,0.271 6.052,0.448 0.24,0.177 10 false *2 5.24,1.781 5.656,1.979 0.417,0.198 10 true M112
*1 No. 5 Relay Block Assembly *2 Fusible Link Block Assembly
*a PM-IGCT Fuse Holder *b IGCT Relay Holder



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IGCT relay holder) or M112-1 (Fusible Link Block Assembly) - Body ground and other terminals Always 10 kΩ or higher
5 (IGCT relay holder) or 1 (PM-IGCT fuse holder) - Body ground and other terminals Always 10 kΩ or higher


c.

Install the PM-IGCT fuse and IGCT relay.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT IG)

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PM-IGCT)

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT IG)