Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM J

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Indicator Circuit  


DESCRIPTION

In accordance with the shift lever position, each shift position indicator light will turn on.

WIRING DIAGRAM

A396736E16
0.083,0.979 1.229,1.208 1.146,0.229 10 false from ACC Relay 1.417,1.177 2.49,1.375 1.073,0.198 10 false ECU-ACC 2.354,0.896 2.625,1.125 0.271,0.229 10 false 1 2.573,1.01 3.031,1.208 0.458,0.198 10 false PWR 3.594,1.021 3.75,1.219 0.156,0.198 10 false P 3.594,1.448 3.75,1.646 0.156,0.198 10 false R 3.594,1.875 3.75,2.094 0.156,0.219 10 false N 3.604,2.302 3.76,2.521 0.156,0.219 10 false D 3.604,2.729 3.76,2.948 0.156,0.219 10 false S 3.813,0.938 4.125,1.229 0.313,0.292 10 false 10 3.813,1.354 3.969,1.552 0.156,0.198 10 false 9 3.813,1.781 3.969,1.979 0.156,0.198 10 false 8 3.813,2.198 3.969,2.396 0.156,0.198 10 false 7 3.813,2.635 3.969,2.833 0.156,0.198 10 false 3 5.656,0.521 6.271,0.719 0.615,0.198 10 false ACCI 5.667,1.031 6.281,1.229 0.615,0.198 10 false INDP 5.667,1.458 6.281,1.656 0.615,0.198 10 false INDR 5.667,1.885 6.281,2.083 0.615,0.198 10 false INDN 5.677,2.313 6.292,2.51 0.615,0.198 10 false INDD 5.677,2.719 6.292,2.917 0.615,0.198 10 false INDM 5.333,0.333 5.646,0.531 0.313,0.198 10 false 29 5.333,0.844 5.646,1.042 0.313,0.198 10 false 19 5.375,1.271 5.688,1.469 0.313,0.198 10 false 7 5.333,1.688 5.646,1.885 0.313,0.198 10 false 21 5.365,2.115 5.677,2.313 0.313,0.198 10 false 8 5.333,2.531 5.646,2.729 0.313,0.198 10 false 20 5.25,0.521 5.708,0.719 0.458,0.198 10 false F160 5.25,1.042 5.865,1.24 0.615,0.198 10 false F161 1.51,3.208 1.917,3.406 0.406,0.198 10 false F162 1.51,3.385 3.01,3.604 1.5,0.219 10 false Shift Position Indicator 5.198,3.188 6.979,3.646 1.781,0.458 10 false Hybrid Vehicle Control ECU 5.26,1.458 5.875,1.656 0.615,0.198 10 false F161 5.26,1.875 5.875,2.073 0.615,0.198 10 false F161 5.26,2.313 5.875,2.51 0.615,0.198 10 false F161 5.25,2.729 5.865,2.927 0.615,0.198 10 false F161

PROCEDURE

1.CHECK SHIFT POSITION INDICATOR
a.

Turn the power switch on (ACC).


b.

Check that each shift position indicator light turns on correctly.

Result:
Result Proceed to
All shift position indicator lights turn on simultaneously A
Shift position indicator lights other than corresponding one turn on B
Corresponding shift position indicator light does not turn on C
No shift position indicator lights turn on D



c.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

B

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

C

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

D

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)
a.

Disconnect the hybrid vehicle control ECU connector.


b.
A365589C18
1.542,0.156 1.938,0.406 0.396,0.25 2.333,1.833 1.917,1.25 true 1.75,1.26 1.667,1.833 true 2.25,0.333 1.865,1.073 true 1.25,0.333 1.667,1.073 true 1.583,1.26 1,1.833 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *a 0.781,1.885 1.25,2.083 0.469,0.198 10 false INDP 2.333,0.219 2.802,0.417 0.469,0.198 10 false INDD 1.583,0.208 1.969,0.406 0.385,0.198 10 false F161 0.875,0.208 1.344,0.406 0.469,0.198 10 false INDR 2.198,1.885 2.667,2.083 0.469,0.198 10 false INDN 1.531,1.885 2,2.083 0.469,0.198 10 false INDM
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F161-19 (INDP) - Body ground and other terminals Always 10 kΩ or higher
F161-7 (INDR) - Body ground and other terminals Always 10 kΩ or higher
F161-21 (INDN) - Body ground and other terminals Always 10 kΩ or higher
F161-8 (INDD) - Body ground and other terminals Always 10 kΩ or higher
F161-20 (INDM) - Body ground and other terminals Always 10 kΩ or higher



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the shift position indicator connector.


c.
A409138C04
1.531,0.208 1.948,0.458 0.417,0.25 0.417,3.417 0.833,3.667 0.417,0.25 1.01,3.01 1.708,3.469 true 1.208,4.229 1.542,3.781 true 1.594,4.24 1.729,3.771 true 1.979,4.24 1.896,3.792 true 2.406,4.281 2.083,3.76 true 1.833,1.188 2.177,0.417 true 1.802,2.021 1.74,1.385 true 1.281,2 1.583,1.385 true 1.271,0.458 1.646,1.219 true 2.427,2.021 1.875,1.396 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 0.25,2.76 0.563,2.917 0.313,0.156 10 false *b 0.885,0.344 1.344,0.542 0.458,0.198 10 false INDR 1.042,2.094 1.5,2.292 0.458,0.198 10 false INDP 2.24,0.333 2.698,0.531 0.458,0.198 10 false INDD 2.375,2.083 2.833,2.281 0.458,0.198 10 false INDN 1.667,2.083 2.125,2.281 0.458,0.198 10 false INDM 1.958,4.302 2.417,4.5 0.458,0.198 10 false R 2.375,4.302 2.833,4.5 0.458,0.198 10 false P 1.542,4.302 2,4.5 0.458,0.198 10 false N 1.125,4.302 1.583,4.5 0.458,0.198 10 false D 0.844,2.854 1.302,3.052 0.458,0.198 10 false S 0.469,3.458 0.927,3.656 0.458,0.198 10 false F162 1.594,0.25 2.052,0.448 0.458,0.198 10 false F161
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Position Indicator)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F161-19 (INDP) or F162-10 (P) - Body ground and other terminals Always 10 kΩ or higher
F161-7 (INDR) or F162-9 (R) - Body ground and other terminals Always 10 kΩ or higher
F161-21 (INDN) or F162-8 (N) - Body ground and other terminals Always 10 kΩ or higher
F161-8 (INDD) or F162-7 (D) - Body ground and other terminals Always 10 kΩ or higher
F161-20 (INDM) or F162-3 (S) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the shift position indicator connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the shift position indicator connector.


b.

Turn the power switch on (ACC).


c.
A409139C05
0.458,0.948 0.844,1.208 0.385,0.26 0.948,0.667 1.344,1.021 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.49,1 0.833,1.208 0.344,0.208 10 false F162 0.552,0.531 0.969,0.76 0.417,0.229 10 false PWR
*a Front view of wire harness connector
(to Shift Position Indicator)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F162-1 (PWR) - Body ground Power switch on (ACC) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the shift position indicator connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)
a.

Turn the power switch on (ACC).


b.

Measure the voltage according to the value(s) in the table below.

A409147C92
3.354,0.25 3.781,0.552 0.427,0.302 2.854,2.313 3.583,1.479 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 3.396,0.313 4.031,0.563 0.635,0.25 10 false F160 2.688,2.354 3.323,2.604 0.635,0.25 10 false ACCI
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
F160-29 (ACCI) - Body ground Power switch on (ACC) 11 to 14 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

6.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Turn the power switch on (ACC).


c.
A365589C19
1.542,0.156 1.938,0.406 0.396,0.25 2.333,1.833 1.917,1.25 true 1.75,1.26 1.667,1.833 true 2.25,0.333 1.865,1.073 true 1.25,0.333 1.667,1.073 true 1.583,1.26 1,1.833 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *a 0.781,1.885 1.25,2.083 0.469,0.198 10 false INDP 2.333,0.219 2.802,0.417 0.469,0.198 10 false INDD 1.583,0.198 1.969,0.396 0.385,0.198 10 false F161 0.875,0.208 1.344,0.406 0.469,0.198 10 false INDR 2.198,1.885 2.667,2.083 0.469,0.198 10 false INDN 1.531,1.885 2,2.083 0.469,0.198 10 false INDM
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F161-19 (INDP) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F161-7 (INDR) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F161-21 (INDN) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F161-8 (INDD) - Body ground and other terminals Power switch on (ACC) 11 to 14 V
F161-20 (INDM) - Body ground and other terminals Power switch on (ACC) 11 to 14 V



d.

Turn the power switch off.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SHIFT POSITION INDICATOR)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the shift position indicator connector.


c.
A409138C05
1.531,0.208 1.948,0.458 0.417,0.25 0.417,3.417 0.833,3.667 0.417,0.25 1.01,3.01 1.708,3.469 true 1.208,4.229 1.542,3.781 true 1.594,4.24 1.729,3.771 true 1.979,4.24 1.896,3.792 true 2.406,4.281 2.083,3.76 true 1.833,1.188 2.177,0.417 true 1.802,2.021 1.74,1.385 true 1.281,2 1.583,1.385 true 1.271,0.458 1.646,1.219 true 2.427,2.021 1.875,1.396 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 0.25,2.76 0.563,2.917 0.313,0.156 10 false *b 0.885,0.344 1.344,0.542 0.458,0.198 10 false INDR 1.042,2.094 1.5,2.292 0.458,0.198 10 false INDP 2.24,0.333 2.698,0.531 0.458,0.198 10 false INDD 2.375,2.083 2.833,2.281 0.458,0.198 10 false INDN 1.667,2.083 2.125,2.281 0.458,0.198 10 false INDM 1.958,4.302 2.417,4.5 0.458,0.198 10 false R 2.375,4.302 2.833,4.5 0.458,0.198 10 false P 1.542,4.302 2,4.5 0.458,0.198 10 false N 1.125,4.302 1.583,4.5 0.458,0.198 10 false D 0.844,2.865 1.302,3.063 0.458,0.198 10 false S 0.479,3.469 0.938,3.667 0.458,0.198 10 false F162 1.594,0.281 2.052,0.479 0.458,0.198 10 false F161
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Shift Position Indicator)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F161-19 (INDP) - F162-10 (P) Always Below 1 Ω
F161-7 (INDR) - F162-9 (R) Always Below 1 Ω
F161-21 (INDN) - F162-8 (N) Always Below 1 Ω
F161-8 (INDD) - F162-7 (D) Always Below 1 Ω
F161-20 (INDM) - F162-3 (S) Always Below 1 Ω



d.

Reconnect the shift position indicator connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR