Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404412 MOTOR GENERATOR CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P1CAD49  Drive Motor "A" Position Sensor Internal Electronic Failure  P1C651F  Generator Control Module Circuit Intermittent  P1CB038  Drive Motor "A" Position Sensor REF Signal Frequency Incorrect  


DESCRIPTION

The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C651F Generator Control Module Circuit Intermittent Excitation signal (REF signal) for resolver angle detection cycle malfunction detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored.
(1 trip detection logic)
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Does not come on Master Warning:
Does not come on
P1CAD49 Drive Motor "A" Position Sensor Internal Electronic Failure Motor resolver angle malfunction:
The difference between the resolver angle for control and estimated resolver angle exceeds the allowable limit.
(1 trip detection logic)
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on
P1CB038 Drive Motor "A" Position Sensor REF Signal Frequency Incorrect Resolver REF signal cycle malfunction:
Excitation signal (REF signal) for resolver angle detection cycle malfunction
(1 trip detection logic)
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


Comes on Master Warning:
Comes on

HINT:

Although the DTC titles generator control module, these DTCs relate to the motor control module.


Related Data List
DTC No. Data List
P1CAD49 Motor Revolution
P1CB038

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.*

*: Lightly wiggle the connectors and wire harnesses up and down and right and left.

7.

Turn the power switch on (READY) and wait for 5 seconds or more.

8.

Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.

9.

Keep the engine running for 5 seconds or more.

10.

Drive the vehicle forward with the shift lever in D for 5 m (16 ft.) or more.

11.

Drive the vehicle backward with the shift lever in R for 5 m (16 ft.) or more.

12.

Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.

13.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C56
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

If the problem symptom cannot be reproduced, performing a road test on a road on which the vehicle tends to vibrate will make it easier to reproduce the symptom.

·

If the resolver is malfunctioning, the vehicle may not drive smoothly.

·

When inspecting the connectors, if it is difficult to judge if a connector was disconnected, deformed or improperly secured, disconnect and reconnect the connector and then check for DTCs again. Check if the same DTC is output. If the same DTC is not output, improper connection of connectors is suspected.

·

As a malfunction detection threshold may be exceeded when performing the vibration or heat connector inspections, make sure to perform the following inspection to check that the DTC was not stored due to the malfunction of a part.



PROCEDURE

1.CHECK DTC OUTPUT (MOTOR GENERATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P1CAD49, P1CB038 or P1C651F only is output, or DTCs except the ones in the table below are also output. A
Any of the following DTCs are also output. B


Relevant DTC
P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A4B16 Generator Position Sensor Circuit Voltage Below Threshold
P0C5013 Drive Motor "A" Position Sensor Circuit "A" Circuit Open
P0C5016 Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Below Threshold
P0C5017 Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Above Threshold
P0C5A13 Drive Motor "A" Position Sensor Circuit "B" Circuit Open
P0C5A16 Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Below Threshold
P0C5A17 Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Above Threshold


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK GENERATOR RESOLVER CIRCUIT

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK GENERATOR RESOLVER CIRCUIT

NEXT

4.CHECK MOTOR RESOLVER CIRCUIT
4.CHECK MOTOR RESOLVER CIRCUIT

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>Motor Resolver Circuit

HINT:

If the "Motor Resolver Circuit" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT