Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › COMBINATION SWITCH › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404425 COMBINATION SWITCH G

M20A-FXS HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84390B 1.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for LHD)

a.

Check the resistance.

i.
A338088C98
1.49,1.917 1.688,1.573 true 2.438,1.927 2.26,1.552 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 2.469,1.958 2.948,2.146 0.479,0.188 10 false E 1.406,1.948 1.656,2.167 0.25,0.219 10 false S
*a Component without harness connected
(EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (S) - 8 (E) EV drive mode switch being pushed and held Below 1 Ω
EV drive mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the EV drive mode switch (electric parking brake switch assembly).



b.

Check illumination.

i.
A338088C99
1.177,1.167 0.844,0.542 true 2.219,1.167 2.615,0.521 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 0.521,0.438 1.135,0.635 0.615,0.198 10 false ILL+ 2.667,0.344 3.281,0.542 0.615,0.198 10 false ILL-
*a Component without harness connected
(EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the EV drive mode switch (electric parking brake switch assembly).

Standard:
Measurement Condition Specified Condition
Auxiliary Battery positive (+) → 7 (ILL+)
Auxiliary Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the EV drive mode switch (electric parking brake switch assembly).



Hide 84390B 2.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for RHD)

a.
C423271C01
1.156,1.938 1.344,1.542 true 2.49,1.938 2.292,1.552 true 1.031,1.948 1.188,2.146 0.156,0.198 10 false S 2.51,1.958 2.667,2.156 0.156,0.198 10 false E 0.083,0.052 0.24,0.25 0.156,0.198 10 false *a
*a Component without harness connected
(EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (S) - 8 (E) EV drive mode switch being pushed and held Below 1 Ω
EV drive mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the EV drive mode switch (electric parking brake switch assembly)


b.

Check illumination.

i.
C423271C02
0.75,0.604 1.146,1.177 true 2.646,0.531 2.229,1.188 true 0.438,0.5 0.865,0.708 0.427,0.208 10 false ILL+ 2.698,0.438 3.125,0.646 0.427,0.208 10 false ILL- 0.042,0.031 0.469,0.24 0.427,0.208 10 false *a
*a Component without harness connected
(EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Apply auxiliary battery voltage between the terminals of the switch, and check the illumination condition of the EV drive mode switch (electric parking brake switch assembly).

OK:
Measurement Condition Specified Condition
Auxiliary Battery positive (+) → 7 (ILL+)
Auxiliary Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the EV drive mode switch (electric parking brake switch assembly)