Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2019.09
RM32K0E _55 Steering _061344 STEERING GEAR / LINKAGE _0299717 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 45047 1.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.
C165553C04
1.292,1.021 1.292,1.521 1.292,1.521 1.823,1.521 false 1.438,1.021 1.438,1.521 false 1.865,1.458 2.208,1.719 0.344,0.26 10 false *a
*a Matchmark


Install the lock nut and tie rod end sub-assembly LH to the steering gear assembly until the matchmarks are aligned.

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45046 2.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 3.INSTALL STEERING LINK ASSEMBLY

a.
C366719C02
0,0 0,0 false
V113147

Install in this Direction


Insert the steering link assembly as shown in the illustration.


b.
C366720

Align the protrusion of the steering link assembly with the hole of the No. 1 steering column hole cover sub-assembly, and install the No. 1 steering column hole cover sub-assembly to the steering link assembly.

HINT:

Check that the No. 1 steering column hole cover sub-assembly is securely installed.



c.

Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 new nuts.

Torque:
133 N*m (1356 kgf*cm, 98 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Make sure to tighten the bolts starting from the left side of the vehicle.




d.

Install the wire harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.


e.

Connect the connector.


Hide 45047 4.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.
C345614

Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45046 5.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43215 6.INSTALL STEERING KNUCKLE SEAL (w/ Seal)

HINT:

Use the same procedure for both sides.


a.
C406723C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the steering knuckle seal as shown in the illustration.

NOTICE:

Make sure that the steering knuckle seal is securely installed.



Hide 45025D 7.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C365808N03
0.167,0.115 0.323,0.313 0.156,0.198 10 false A 2.156,2.375 2.313,2.573 0.156,0.198 10 false B

Engage the clip (B) to the vehicle body.


b.

Engage the clip (A) to install the No. 1 steering column hole cover sub-assembly to the vehicle body.

NOTICE:

Be careful not to damage the lip of the No. 1 steering column hole cover sub-assembly.



Hide 45260 8.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 9.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 10.INSTALL FRONT WHEELS

Hide 12.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT