Home › Drivetrain › P711 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › from 2019.09
RM32K0E _52 Drivetrain _084042 P711 HYBRID TRANSMISSION / TRANSAXLE _0404800 SHIFT LEVER G

P711 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT LOCK CONTROL ECU

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect wire harness:

i.
C365111

Disconnect the shift lock control ECU connector.


ii.
C269340C21
2.135,1.531 2.563,1.24 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 2.615,1.146 2.823,1.323 0.208,0.177 10 false IG
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C269340C22
1.948,1.5 2.531,0.833 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 2.583,0.76 2.917,0.938 0.333,0.177 10 false STP
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (STP) - Body ground Ready ON, brake pedal depressed 11 to 14 V
Ready ON, brake pedal released Below 1 V


If the result is not as specified, repair or replace the wire harness or connector or replace the hybrid vehicle control ECU assembly.


iv.
C269340C23
0.688,1.125 1.26,1.542 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 0.531,1.042 0.74,1.219 0.208,0.177 10 false E
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect shift lock solenoid:

i.
C366439

Disconnect the shift lock solenoid connector.


ii.
C322125C06
1.5,2.667 1.781,2.125 true 2.385,2.667 2.094,2.135 true 1.292,2.667 1.906,2.865 0.615,0.198 10 false E2 2.448,2.656 3.063,2.854 0.615,0.198 10 false P 0.115,0.094 0.729,0.292 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


If the result is not as specified, replace the shift lock control unit assembly.


iii.
C322125C07
0.99,2.573 1.365,2.125 true 2.01,2.604 1.656,2.125 true 0.573,2.531 1.188,2.729 0.615,0.198 10 false SLS+ 2.073,2.531 2.688,2.729 0.615,0.198 10 false SLS- 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


If the result is not as specified, replace the shift lock control unit assembly.



Hide 2.INSPECT TRANSMISSION CONTROL SWITCH (for LHD)

a.
C365112

Disconnect the transmission control switch connector.


b.
C422407C01
1.875,1.781 2.01,1.385 true 2.552,1.76 2.292,1.396 true 1.26,1.76 1.729,1.385 true 0.958,0.5 1.396,1.26 true 0.823,1.281 1.135,1.281 true 2.427,1.833 2.927,2.031 0.5,0.198 10 false SFTD 1.844,1.823 2.156,2.021 0.313,0.198 10 false E 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.042,1.823 1.521,2.021 0.479,0.198 10 false SFTU 0.865,0.354 1.344,0.552 0.479,0.198 10 false IG 0.698,1.208 1.177,1.406 0.479,0.198 10 false M
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (M) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.


Hide 3.INSPECT TRANSMISSION CONTROL SWITCH (for RHD)

a.
C366467

Disconnect the transmission control switch connector.


b.
C422407C02
1.875,1.781 2.01,1.385 true 2.552,1.76 2.292,1.396 true 1.26,1.76 1.729,1.385 true 0.958,0.5 1.396,1.26 true 0.823,1.281 1.135,1.281 true 2.427,1.833 2.927,2.031 0.5,0.198 10 false SFTU 1.844,1.823 2.156,2.021 0.313,0.198 10 false E 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.042,1.823 1.521,2.021 0.479,0.198 10 false SFTD 0.865,0.354 1.344,0.552 0.479,0.198 10 false IG 0.698,1.208 1.177,1.406 0.479,0.198 10 false M
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (M) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.