Home › General › MAINTENANCE › M20A-FXS COOLANT (for Engine) › from 2019.09
RM32K0E _V1 General _059911 MAINTENANCE _0404856 M20A-FXS COOLANT(for Engine) A

MAINTENANCE  M20A-FXS COOLANT(for Engine)  REPLACEMENT  


PROCEDURE

Hide 51444A 1.REMOVE REAR ENGINE UNDER COVER LH

a.
A433971

Remove the 2 screws, 6 clips and rear engine under cover LH from the vehicle.


Hide 2.DRAIN ENGINE COOLANT (for Engine)

CAUTION:
·

When engine coolant is hot, do not remove the reserve tank cap, air release valve or the radiator drain cock plug.

·

Fluid and steam may spray out due to high pressure, possibly resulting in burns.

A452382C01
5.917,3.552 6.313,3.552 true 5.625,1.333 5.354,1.635 true 1.052,0.635 1.229,0.344 true 6.333,3.458 6.521,3.635 0.188,0.177 10 true *2 5.177,1.625 5.365,1.823 0.188,0.198 10 true *1 1.229,0.219 1.417,0.417 0.188,0.198 10 true *3
*1 Reserve Tank Cap *2 Radiator Drain Cock Plug
*3 Air Release Valve - -




a.
A432790C01
1.438,1.927 1.792,1.927 true 1.823,1.823 2.021,2.01 0.198,0.188 10 true *a
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.

Loosen the radiator drain cock plug.


c.
A432791C01
1.75,0.365 1.948,0.24 false 1.042,0.302 1.385,0.479 true 2.458,2.74 2.667,2.917 false 1.979,0.146 2.292,0.302 0.313,0.156 10 false *1 2.708,2.875 3.021,3.031 0.313,0.156 10 false *2 0.865,0.198 1.177,0.354 0.313,0.156 10 false *3
*1 Reserve Tank Cap
*2 Radiator Drain Cock Plug
*3 Air Release Valve


Remove the reserve tank cap. Then drain the engine coolant.

HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD ENGINE COOLANT (for Engine)

a.
A432792C01
1.573,2.365 1.802,2.146 true 2.167,0.823 2.396,0.604 true 2.417,0.51 2.604,0.688 0.188,0.177 10 true *a 1.823,2.063 2.01,2.25 0.188,0.188 10 true *a
*a Air Release Valve


Using a 6 mm hexagon socket wrench, remove the air release valve from the radiator reserve tank assembly.


b.
A421316

Add engine coolant to the level shown in the illustration.

Standard Capacity:

5.9 liters (6.2 US qts, 5.2 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



c.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

If the engine coolant level is low, add engine coolant.


d.

Using a 6 mm hexagon socket wrench, install the air release valve to the radiator reserve tank assembly.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


e.

Install the reserve tank cap.

NOTICE:

Securely tighten the reserve tank cap as much as possible.



f.

Perform the following procedure to set the engine to engine coolant filling mode.

HINT:

It is necessary to set the engine to engine coolant filling mode to ensure that a certain engine water pump assembly (water inlet housing) speed is maintained in order to circulate engine coolant.


i.

Move the shift lever to P.


ii.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

iii.

Start the engine.


iv.

Run the engine at 1500 rpm or more for 15 seconds or more.


v.

Check that the speed of the electric water pump increases when the engine is raced to 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Electric Water Pump Speed
50003 372 211,359
Standard:
Tester Display Condition Specified Condition
Electric Water Pump Speed The engine is being raced to 2500 rpm. When the engine speed increases, the speed of the electric water pump also increases.


NOTICE:

Do not move the shift lever from P, or engine coolant filling mode will be canceled.


HINT:

The speed of the engine water pump assembly (water inlet housing) changes in accordance with the engine speed when the engine is being raced in engine coolant filling mode.




g.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off.

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.

Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

HINT:

The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.



ii.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.

CAUTION:

When squeezing the No. 1 radiator hose and No. 2 radiator hose:

·

Wear protective gloves.

·

Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.

·

Keep your hands away from the fan LH and fan RH.



NOTICE:
·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

Make sure that the reserve tank assembly still has some engine coolant in it.

·

If the reserve tank assembly does not have enough engine coolant, the engine may overheat or be seriously damaged.

·

If the reserve tank assembly does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the reserve tank assembly is filled to the full line.



HINT:

If the flowing sound of engine coolant can still be heard after bleeding air, perform the following procedure to bleed air again.

1.

Warm up the engine. (With the engine idling, check that the engine coolant is flowing into the reserve tank assembly.)

2.

Run the engine at 2000 rpm for 2 minutes or more. (A)

3.

Leave the engine idling for 2 minutes or more. (B)

4.

Repeat steps (A) and (B) 4 times or more.





h.
A391006C09
1.74,1.063 2.552,0.75 2.552,0.75 2.771,0.75 false 1.75,1.25 2.521,1.51 2.521,1.51 2.76,1.51 false 2.813,0.635 3.125,0.792 0.313,0.156 10 false *a 2.813,1.406 3.125,1.563 0.313,0.156 10 false *b
*a Full Line
*b Low Line


After the engine has cooled down, check that the engine coolant level is between the full and low lines.

NOTICE:

The coolant levels in the compartments inside the radiator reserve tank assembly may differ, but this is not a malfunction.


If the engine coolant level is below the low line, add engine coolant to the full line.


Hide 4.INSPECT FOR COOLANT LEAK (for Engine)

Hide 51444A 5.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH to the vehicle with the 2 screws and 6 clips.