Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2ZR-FXE) › from 2019.09
RM32K0E _52 Drivetrain _061224 DRIVE SHAFT / PROPELLER SHAFT _0405859 FRONT DRIVE SHAFT ASSEMBLY(for 2ZR-FXE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2ZR-FXE)  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for TMMT Made)

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C108564

Using pliers, separate the front No. 2 axle inboard joint boot clamp.


Hide 43448G 2.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for TMC Made)

a.
C286096

Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp.


Hide 43448F 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.


Hide 4.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 5.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (for TMMT Made)

a.

Remove the old grease from the front drive inboard joint assembly.


b.
F045461C08
1.99,0.646 1.99,0.25 1.99,0.25 1.198,0.25 false 1.677,0.938 1.677,0.25 false 1.01,0.146 1.177,0.292 0.167,0.146 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C160822

Using a snap ring expander, remove the front drive inner shaft inner shaft snap ring from the front drive outboard joint shaft assembly.


f.
C141145C17
2.854,1.073 1.844,1.479 1.844,1.479 2.885,1.135 true 1.646,1.427 1.833,1.583 0.188,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Do not drop the tripod joint.




Hide 6.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (for TMC Made)

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C158439C17
1.385,1.24 1.125,0.458 1.125,0.458 1.927,0.667 true 0.948,0.365 1.344,0.521 0.396,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

NOTICE:
·

Be careful when removing the front drive inboard joint assembly from the front drive outboard joint shaft assembly as the rollers of the tripod joint may fall out.

·

Do not drop the rollers of the tripod joint.




d.
C348430

Remove the 3 rollers from the tripod joint.


e.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



f.
C348431

Using a snap ring expander, remove the front drive inner shaft inner shaft snap ring from the front drive outboard joint shaft assembly.


g.
C348432C02
2.833,1 1.74,1.667 1.74,1.667 2.875,1.104 true 1.573,1.583 1.885,1.74 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



h.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Do not drop the tripod joint.




i.
C265836

Remove the front axle inboard joint grommet from the front drive inboard joint assembly.


Hide 7.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474E 8.REMOVE FRONT DRIVE SHAFT DAMPER LH (for TMMT Made)

a.
C310867

Using needle-nose pliers, separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper LH and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43474E 9.REMOVE FRONT DRIVE SHAFT DAMPER LH (for TMC Made)

a.
C304762

Using needle-nose pliers, disengage the claw engagement and separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper LH and 2 front drive shaft damper clamps.


Hide 43474D 10.REMOVE FRONT DRIVE SHAFT DAMPER RH (for TMC Made)

HINT:

Use the same procedure as for the LH side.


Hide 43447F 11.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for TMMT Made LH Side)

a.
C282245

Using pliers, separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.


Hide 43447F 12.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for TMC Made LH Side)

a.
C286102

Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp.


Hide 43447E 13.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 14.REMOVE FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.


Hide 41336E 15.REMOVE FRONT DRIVE SHAFT DUST COVER

HINT:

Only perform the following procedure if the front drive shaft dust cover is deformed.


a.
C235586E01
1.885,1.448 2.698,1.688 true 2.74,1.615 3.198,1.813 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft dust cover.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.