Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for M20A-FXS) › from 2019.09
RM32K0E _52 Drivetrain _061224 DRIVE SHAFT / PROPELLER SHAFT _0405862 FRONT DRIVE SHAFT ASSEMBLY(for M20A-FXS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for M20A-FXS)  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C411286

Using pliers, separate the front No. 2 axle inboard joint boot clamp.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.


Hide 3.SEPARATE FRONT AXLE INBOARD JOINT BOOT

a.

Separate the front axle inboard joint boot from the front drive inboard joint assembly.


Hide 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C411287C01
2.01,0.51 0.938,0.25 0.938,0.25 1.823,1 true 0.74,0.156 1,0.417 0.26,0.26 10 false *a
*a Matchmark


Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.


d.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C411288

Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.


f.
C141145C17
2.854,1.073 1.844,1.479 1.844,1.479 2.885,1.135 true 1.646,1.427 1.833,1.583 0.188,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the areas where the rollers contact the tripod joint.

·

Do not drop the tripod joint.




h.
C411289

Remove the front axle inboard joint grommet from the front drive inboard joint assembly.


Hide 5.REMOVE FRONT AXLE INBOARD JOINT BOOT

a.

Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.


Hide 43474E 6.REMOVE FRONT DRIVE SHAFT DAMPER LH

a.
C411290

Using pliers, separate the 2 front drive shaft damper clamps.


b.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.


Hide 43447F 7.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

a.
C282245

Using pliers, separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.


Hide 43447E 8.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 9.REMOVE FRONT AXLE OUTBOARD JOINT BOOT (for LH Side)

a.

Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.


b.

Remove the old grease from the front drive outboard joint shaft assembly.


Hide 41336E 10.REMOVE FRONT DRIVE SHAFT DUST COVER

HINT:

Only perform the following procedure if the front drive shaft dust cover is deformed.


a.
C235586E01
1.885,1.448 2.698,1.688 true 2.74,1.615 3.198,1.813 0.458,0.198 10 false SST

Using SST and a press, remove the front drive shaft dust cover.

SST
09950-00020  

NOTICE:
·

Be careful not to drop the front drive inboard joint assembly.

·

Do not overtighten SST.