Home › Engine / Hybrid System › M20A-FXS (FUEL) › FUEL TANK › from 2019.09
RM32K0E _51 Engine / Hybrid System _083996 M20A-FXS FUEL _0404510 FUEL TANK A

M20A-FXS FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77754B 1.INSTALL CHARCOAL CANISTER OUTLET HOSE

a.

Engage the 2 clamps to install the charcoal canister outlet hose to the fuel tank assembly.


Hide 77209F 2.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 3 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77026A 3.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Engage the 3 clamps to install the No. 1 fuel evaporation tube sub-assembly to the fuel tank assembly.


Hide 77100 4.INSTALL FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.

Set the fuel tank assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.

Using the engine lifter, slowly raise the fuel tank assembly, and then temporarily install the fuel tank assembly with the 4 bolts.


c.
A398096N01
2.698,0.052 2.802,0.208 0.104,0.156 10 true 1 2.615,1.99 2.74,2.146 0.125,0.156 10 true 2 1.073,0.271 1.177,0.438 0.104,0.167 10 true 3 0.802,1.979 0.917,2.135 0.115,0.156 10 true 4

Tighten the 4 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




d.

Connect the fuel tank breather tube to the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 5.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 6.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A432271C03
1.656,3.26 1.969,3.417 0.313,0.156 10 false *a 1.604,2.01 2.01,2.333 0.406,0.323 10 false *b
*a 120°
*b Up


Connect the No. 1 fuel evaporation tube sub-assembly to the fuel pipe and slide the clip to secure it.


Hide 77213E 7.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A440774C02
1.208,3.229 1.385,3.229 1.385,3.229 1.656,3.094 true 1.688,3.25 1.927,3.323 1.927,3.323 2.167,3.323 false 2.26,2.958 2.771,2.958 true 2.125,2.281 2.5,2.5 0.375,0.219 10 false *a 2.833,2.854 3.073,3.073 0.24,0.219 10 false *b 1.604,2.083 1.833,2.24 0.229,0.156 10 false *c 1.063,3.135 1.313,3.365 0.25,0.229 10 false *d 2.177,3.198 2.417,3.396 0.24,0.198 10 false *e
*a 120°
*b 15°
*c Top of Vehicle
*d Paint Mark (Fuel Tank To Filler Pipe Hose)
*e Protrusion (Fuel Tank Assembly)


Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.

HINT:

Make sure the clamp and fuel tank to filler pipe hose are positioned within the area shown in the illustration.



Hide 8.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A451709C02
1.583,3.25 1.792,3.417 0.208,0.167 10 false *a 1.698,2.188 1.906,2.354 0.208,0.167 10 false *b
*a 120°
*b Up


Connect the charcoal canister outlet hose to the fuel tank filler pipe sub-assembly.


Hide 77641A 9.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the fuel tank assembly with the 4 clips.


Hide 57628C 10.INSTALL REAR FLOOR SIDE MEMBER COVER LH

a.
A393592N03
0.552,1.813 0.708,2.01 0.156,0.198 10 true A 2,0.156 2.156,0.354 0.156,0.198 10 true B

Install the rear floor side member cover LH with the clip (B).


b.

Install the 3 bolts and clip (A).

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 57627A 11.INSTALL REAR FLOOR SIDE MEMBER COVER RH

a.

Install the rear floor side member cover RH with the clip.


b.

Install the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 17430 12.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 77020A 13.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 14.ADD FUEL

Hide 15.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>M20A-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION