Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.09–2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0407275 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B1570  Red LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the power switch is turned to ON.

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1570 Red LED Error Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 10 seconds or more when the power switch is on (IG)
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E354565E46
1.896,1.021 2.354,1.219 0.458,0.198 10 false RED 2.979,0.583 3.135,0.781 0.156,0.198 10 false 6 2.979,1.146 3.292,1.385 0.313,0.24 10 false 1 2.531,0.625 3.146,0.823 0.615,0.198 10 false IND1 2.469,1.156 3.083,1.354 0.615,0.198 10 false GND3 0.865,2.094 1.323,2.292 0.458,0.198 10 false R15 0.854,2.26 2.885,2.688 2.031,0.427 10 false Map Light Assembly 4.896,0.594 5.208,0.792 0.313,0.198 10 false 11 4.885,1.156 5.198,1.354 0.313,0.198 10 false 26 5.167,0.729 5.781,0.927 0.615,0.198 10 false IND1 5.167,1.167 5.781,1.365 0.615,0.198 10 false SIG- 5.063,2.073 6,2.323 0.938,0.25 10 false F165 5.042,2.25 7.135,2.677 2.094,0.427 10 false Telematics Transceiver 0.958,1.677 2.99,2.104 2.031,0.427 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



HINT:

If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
a.
B234642C53
0.375,0.813 0.75,1.073 0.375,0.26 2.313,1.063 2.635,0.802 true 1.646,1.115 1.938,1.802 true 0.115,0.094 0.417,0.417 0.302,0.323 10 false *a 2.677,0.656 3.219,0.885 0.542,0.229 10 false GND3 1.979,1.729 2.385,1.896 0.406,0.167 10 false IND1 0.438,0.865 0.896,1.063 0.458,0.198 10 false R15
*a Component with harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R15-6 (IND1) - R15-1 (GND3) 2 seconds after power switch turned to ON
→ Power switch off
8.5 to 10 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
a.
B129570C96
1.427,1.813 1.635,1.115 true 2.594,1.76 2.427,1.333 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.625,1.75 3.146,1.969 0.521,0.219 10 false GND3 1.25,1.865 1.688,2.073 0.438,0.208 10 false IND1
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Check map light assembly (manual (SOS) switch) illumination (red).

i.

Apply battery voltage between the terminals of the map light assembly (manual (SOS) switch) and check the illumination (red) condition of map light assembly (manual (SOS) switch).

OK:
Measurement Specified Condition
Battery positive (+) → R15-6 (IND1) Map light assembly (manual (SOS) switch) illuminates (red)
Battery positive (-) → R15-1 (GND3)




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F165 telematics transceiver connector.


b.

Disconnect the R15 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F165-11 (IND1) - R15-6 (IND1) Always Below 1 Ω
F165-11 (IND1) or R15-6 (IND1) - Body ground Always 10 kΩ or higher
F165-26 (SIG-) - R15-1 (GND3) Always Below 1 Ω
F165-26 (SIG-) or R15-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT