Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.09–2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0407275 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B1571  Green LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (green) illuminates after the power switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.

If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1571 Green LED Error Current for the manual (SOS) switch indicator (green) exceeds malfunction threshold for 10 seconds or more when the power switch is on (IG)
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E354565E47
1.771,1.021 2.365,1.219 0.594,0.198 10 false GREEN 2.979,0.615 3.323,0.979 0.344,0.365 10 false 5 2.948,1.156 3.406,1.427 0.458,0.271 10 false 1 2.521,0.594 3.135,0.792 0.615,0.198 10 false IND2 2.458,1.156 3.073,1.354 0.615,0.198 10 false GND3 0.875,2.063 1.333,2.26 0.458,0.198 10 false R15 0.885,2.219 2.927,2.656 2.042,0.438 10 false Map Light Assembly 4.896,0.594 5.208,0.792 0.313,0.198 10 false 12 4.896,1.156 5.208,1.354 0.313,0.198 10 false 26 5.167,0.708 5.781,0.906 0.615,0.198 10 false IND2 5.167,1.156 5.781,1.354 0.615,0.198 10 false SIG- 5.083,2.063 6.021,2.365 0.938,0.302 10 false F165 5.073,2.26 6.99,2.781 1.917,0.521 10 false Telematics Transceiver 1,1.677 3.042,2.115 2.042,0.438 10 false Manual (SOS) Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (INPUT VOLTAGE)
a.
B234642C54
0.396,0.771 0.833,1.031 0.438,0.26 2.313,1.083 2.698,0.844 true 1.771,1.125 2.156,1.75 true 0.083,0.063 0.313,0.313 0.229,0.25 10 false *a 2.74,0.75 3.24,0.979 0.5,0.229 10 false GND3 2.052,1.813 2.49,2.063 0.438,0.25 10 false IND2 0.49,0.823 0.948,1.021 0.458,0.198 10 false R15
*a Component with harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R15-5 (IND2) - R15-1 (GND3) 2 seconds after power switch turned to ON
→ Power switch off
8.5 to 10 V
→ Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)
a.
B129570C97
1.417,1.865 1.073,1.333 true 2.896,1.76 2.594,1.115 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.813,1.813 3.375,2.063 0.563,0.25 10 false GND3 1.469,1.813 1.906,2.021 0.438,0.208 10 false IND2
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Check map light assembly (manual (SOS) switch) illumination (green).

OK:
Measurement Condition Specified Condition
Battery positive (+) → R15-7 (RRID) Map light assembly (manual (SOS) switch) illuminates (green)
Battery positive (-) → R15-1 (GND3)


i.

Apply battery voltage between the terminals of the map light assembly (manual (SOS) switch) and check the illumination (green) condition of map light assembly (manual (SOS) switch).



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the F165 telematics transceiver connector.


b.

Disconnect the R15 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F165-12 (IND2) - R15-5 (IND2) Always Below 1 Ω
F165-12 (IND2) or R15-5 (IND2) - Body ground Always 10 kΩ or higher
F165-26 (SIG-) - R15-1 (GND3) Always Below 1 Ω
F165-26 (SIG-) or R15-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT