Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2019.09–2022.01
RM32K0E _56 Audio / Visual / Telematics _084041 TELEMATICS _0407275 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a communication telematics box signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the power switch is on (IG)
·

Telematics transceiver

·

Communication telematics box

·

Harness or connector

·

Map light assembly



WIRING DIAGRAM

E427363E02
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 1.01,3.771 1.625,3.969 0.615,0.198 10 false MICV 1.052,3.354 1.667,3.552 0.615,0.198 10 false MCI- 5.667,1.396 6.281,1.594 0.615,0.198 10 false MCMD 5.667,1.781 6.281,1.979 0.615,0.198 10 false SP+ 5.667,2.198 6.281,2.396 0.615,0.198 10 false SP- 5.656,2.583 6.271,2.781 0.615,0.198 10 false MCI+ 5.646,3 6.26,3.198 0.615,0.198 10 false MCVD 5.635,3.771 6.25,3.969 0.615,0.198 10 false MICV 5.635,3.396 6.25,3.594 0.615,0.198 10 false MCI- 5.531,4.792 7.063,5.49 1.531,0.698 10 false Telematics Transceiver 4.031,3.99 4.688,4.219 0.656,0.229 10 false * 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.573 1.146,4.979 0.771,0.406 10 false R16 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.469,2.104 2.083,2.302 0.615,0.198 10 false 8 1.469,3.635 2.083,3.833 0.615,0.198 10 false 5 1.469,2.865 2.083,3.063 0.615,0.198 10 false 2 1.479,2.49 2.094,2.688 0.615,0.198 10 false 7 1.469,3.281 2.083,3.479 0.615,0.198 10 false 4 5.344,1.677 5.958,1.875 0.615,0.198 10 false 20 5.333,1.292 5.948,1.49 0.615,0.198 10 false 14 5.354,2.073 5.969,2.271 0.615,0.198 10 false 21 5.354,2.458 5.969,2.656 0.615,0.198 10 false 34 5.354,2.865 5.979,3.063 0.625,0.198 10 false 33 5.344,3.656 5.969,3.854 0.625,0.198 10 false 31 5.531,4.604 6.302,5.01 0.771,0.406 10 false F165 5.646,4.198 6.26,4.396 0.615,0.198 10 false SGND 5.354,4.083 5.979,4.281 0.625,0.198 10 false 32 5.365,3.26 5.99,3.458 0.625,0.198 10 false 35 0.344,5.458 2.521,5.781 2.177,0.323 10 false *: Shielded 2.604,4.073 3.26,4.302 0.656,0.229 10 false * 1.021,2.573 1.635,2.771 0.615,0.198 10 false MCI+ 0.958,2.979 1.573,3.177 0.615,0.198 10 false MCVD

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TELEMATICS TRANSCEIVER
2.CHECK TELEMATICS TRANSCEIVER
a.
B518361C12
1.479,0.135 1.896,0.365 0.417,0.229 1.385,1.833 1.604,1.313 true 0.823,1.615 1.26,1.313 true 0.083,0.094 0.438,0.385 0.354,0.292 10 false *a 0.531,1.635 1.063,1.875 0.531,0.24 10 false MCI- 1.031,1.865 1.563,2.104 0.531,0.24 10 false MICV 1.542,0.177 2.073,0.417 0.531,0.24 10 false F165
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F165-31 (MICV) - Body ground Power switch on (ACC) 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
F165-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - COMMUNICATION TELEMATICS BOX)

NG

5.REPLACE TELEMATICS TRANSCEIVER
3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - COMMUNICATION TELEMATICS BOX)
a.

Disconnect the F165 telematics transceiver connector.


b.

Disconnect the R16 communication telematics box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F165-14 (MCMD) - R16-1 (MCMD) Always Below 1 Ω
F165-20 (SP+) - R16-3 (SP+) Always Below 1 Ω
F165-21 (SP-) - R16-8 (SP-) Always Below 1 Ω
F165-34 (MCI+) - R16-7 (MCI+) Always Below 1 Ω
F165-33 (MCVD) - R16-2 (MCVD) Always Below 1 Ω
F165-35 (MCI-) - R16-4 (MCI-) Always Below 1 Ω
F165-31 (MICV) - R16-5 (MICV) Always Below 1 Ω
F165-14 (MCMD) or R16-1 (MCMD) - Body ground Always 10 kΩ or higher
F165-20 (SP+) or R16-3 (SP+) - Body ground Always 10 kΩ or higher
F165-21 (SP-) or R16-8 (SP-) - Body ground Always 10 kΩ or higher
F165-34 (MCI+) or R16-7 (MCI+) - Body ground Always 10 kΩ or higher
F165-33 (MCVD) or R16-2 (MCVD) - Body ground Always 10 kΩ or higher
F165-35 (MCI-) or R16-4 (MCI-) - Body ground Always 10 kΩ or higher
F165-31 (MICV) or R16-5 (MICV) - Body ground Always 10 kΩ or higher
F165-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE COMMUNICATION TELEMATICS BOX

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION TELEMATICS BOX IS DEFECTIVE)

NG

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT