Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) J

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  Pattern Select Switch EV Mode Circuit  


DESCRIPTION

The EV drive mode signal will be sent to the hybrid vehicle control ECU when the EV drive mode switch (electric parking brake switch assembly) is operated. If the specified conditions are met, the system enters EV drive mode and the vehicle will be driven using EV drive mode. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter assembly to illuminate the EV drive mode indicator.

WIRING DIAGRAM

A376617E04
1.49,1.25 3.438,1.563 1.948,0.313 10 false Combination Meter Assembly 2.104,1.896 2.854,2.156 0.75,0.26 10 false EV MODE 1.281,2.854 3.719,3.292 2.438,0.438 10 false EV Drive Mode Switch (Electric Parking Brake Switch Assembly) 4.708,2.958 6.49,3.448 1.781,0.49 10 false Hybrid Vehicle Control ECU 5.104,2.063 5.688,2.323 0.583,0.26 10 false EVSW 4.802,2.063 5.083,2.344 0.281,0.281 10 false 15 4.719,2.76 5,3.042 0.281,0.281 10 false F3 1.292,2.667 1.573,2.948 0.281,0.281 10 false F67 5.76,1.635 6.042,1.917 0.281,0.281 10 false +B 1.563,2.063 1.844,2.344 0.281,0.281 10 false 8 1.76,2.073 2.25,2.271 0.49,0.198 10 false E 3,2.073 3.281,2.354 0.281,0.281 10 false S 3.198,1.896 3.531,2.125 0.333,0.229 10 false 11*1 0.583,3.385 2.531,3.698 1.948,0.313 10 false : CAN Communication Line 3.198,2.073 3.563,2.344 0.365,0.271 10 false 13*2 0.167,2.792 0.958,2.979 0.792,0.188 10 false *1: for LHD 0.177,3.052 0.969,3.24 0.792,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

Depending on the condition of the hybrid control system and the driving conditions, the drive mode may not be able to be changed to EV mode and a warning message will be displayed on the multi-information display.

HINT:

Under the following conditions, the drive mode will not be able to be changed to EV mode:

·

The hybrid control system is extremely hot.

-

After the vehicle has been parked in an extremely hot environment, driven at high speeds or the vehicle is climbing a slope, etc.


·

The hybrid control system is extremely cold.

-

After the vehicle has been parked in an extremely cold environment (approximately 0°C or less) for a long period of time.


·

The engine is warming up.

·

The SOC (State of Charge) of the HV battery is low.

-

The HV battery SOC displayed on the hybrid system indicator display is low.


·

The vehicle is being driven at a speed higher than the specified value.

-

The vehicle speed is approximately 30 km/h or higher.


·

The accelerator pedal is being fully depressed or the vehicle is climbing a slope.

·

The defroster is on.

·

DTCs are stored.



PROCEDURE

1.ASK ABOUT VEHICLE CONDITION
a.

Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV drive mode.

Result:
Result Proceed to
No buzzer sounded and no message was displayed on multi-information display. A
A buzzer sounded and a message was displayed on multi-information display. B


HINT:

If a buzzer sounds and a message is displayed on the multi-information display, one or more of the EV drive mode entry conditions have not been met. Check that all of the EV drive mode entry conditions have been met before pressing the EV drive mode switch (electric parking brake switch assembly).




A

2.READ VALUE USING GTS (CAN BUS CHECK)

B

END

2.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / CAN Bus Check.

CAN Bus Check
50007
Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B



e.

Turn the power switch off.



A

3.CHECK DTC OUTPUT (HEALTH CHECK)

B

3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.

Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



f.

Turn the power switch off.



A

4.READ VALUE USING GTS (EV MODE, EV MODE SW)

B

GO TO DTC CHART

4.READ VALUE USING GTS (EV MODE, EV MODE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / EV Mode, EV Mode SW.

Powertrain > Hybrid Control > Data List
Tester Display
EV Mode
EV Mode SW
50003 397 79,80

e.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
EV Mode EV drive mode transition availability ON or OFF In EV drive mode: ON
EV Mode SW EV drive mode switch (electric parking brake switch assembly) condition ON or OFF EV drive mode switch (electric parking brake switch assembly) being pushed and held: ON
EV drive mode switch (electric parking brake switch assembly) not pushed: OFF
Result:
Result Proceed to
The display changes according to the EV drive mode switch (electric parking brake switch assembly) operation. A
The display does not change according to the EV drive mode switch (electric parking brake switch assembly) operation. B



f.

Turn the power switch off.



A

B

5.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
5.INSPECT EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Remove the EV drive mode switch (electric parking brake switch assembly).

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>COMBINATION SWITCH>REMOVAL


b.
A338088C45
0.344,1.135 0.74,1.365 0.396,0.229 1.865,1.917 1.719,1.552 true 1.219,1.948 1.333,1.563 true 2.302,1.396 2.688,0.896 true 0.323,0.24 0.635,0.438 0.313,0.198 10 false *a 0.417,1.188 0.729,1.385 0.313,0.198 10 false F67 0.917,1.969 1.24,2.125 0.323,0.156 10 false S *B 2.76,0.813 3.271,1.01 0.51,0.198 10 false E 1.875,1.927 2.198,2.083 0.323,0.156 10 false S *A
*A for LHD
*B for RHD
*a Component without harness connected
(EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F67-11 (S) - F67-8 (E) EV drive mode switch (electric parking brake switch assembly) being pushed and held Below 1 Ω
EV drive mode switch (electric parking brake switch assembly) not pushed 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F67-13 (S) - F67-8 (E) EV drive mode switch (electric parking brake switch assembly) being pushed and held Below 1 Ω
EV drive mode switch (electric parking brake switch assembly) not pushed 10 kΩ or higher



c.

Install the EV drive mode switch (electric parking brake switch assembly).


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the EV drive mode switch (electric parking brake switch assembly) connector.


b.
A373476C05
0.427,0.885 0.844,1.135 0.417,0.25 0.844,1.688 1.24,1.271 true 0.115,0.156 0.427,0.313 0.313,0.156 10 false *a 0.521,0.958 0.802,1.167 0.281,0.208 10 false F67 0.74,1.677 1.146,1.865 0.406,0.188 10 false E
*a Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-8 (E) - Body ground Always Below 1 Ω



c.

Reconnect the EV drive mode switch (electric parking brake switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - EV DRIVE MODE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the EV drive mode switch (electric parking brake switch assembly) connector.


c.
A389531C01
1.833,3.417 2.25,3.667 0.417,0.25 0.167,3.417 0.583,3.667 0.417,0.25 2.5,0.167 2.833,0.417 0.333,0.25 2.271,2.146 2.563,1.844 true 0.833,4.25 1.073,3.813 true 3.188,4.271 2.938,3.823 true 0.344,2.979 0.656,3.188 0.313,0.208 12 false *A 2,2.979 2.313,3.188 0.313,0.208 12 false *B 0.167,0.156 0.479,0.313 0.313,0.156 10 false *a 0.188,2.667 0.5,2.823 0.313,0.156 10 false *b 1.813,2.052 2.271,2.25 0.458,0.198 10 false EVSW 0.677,4.188 0.99,4.344 0.313,0.156 10 false S 3.25,4.188 3.385,4.427 0.135,0.24 10 false S 2.583,0.208 2.833,0.375 0.25,0.167 10 false F3 0.26,3.458 0.583,3.646 0.323,0.188 10 false F67 1.927,3.458 2.25,3.646 0.323,0.188 10 false F67
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to EV Drive Mode Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F3-15 (EVSW) - F67-11 (S) Always Below 1 Ω
F3-15 (EVSW) or F67-11 (S) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F3-15 (EVSW) - F67-13 (S) Always Below 1 Ω
F3-15 (EVSW) or F67-13 (S) - Body ground Always 10 kΩ or higher



d.

Reconnect the EV drive mode switch (electric parking brake switch assembly) connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR