The hybrid vehicle control ECU sends signals such as A/T information signals, dynamic radar cruise control operation signals, brake operation demand signals, and buzzer operation demand signals to the skid control ECU (brake booster with master cylinder assembly) when the dynamic radar cruise control is operating. Therefore, if the skid control ECU (brake booster with master cylinder assembly) detects a communication error with the hybrid vehicle control ECU, it sends a malfunction signal back to the hybrid vehicle control ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P163181 | Communication Error from ECM to VSC Invalid Serial Data Received | While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU continuously receives a logical error signal from the skid control ECU (brake booster with master cylinder assembly) for approximately 1 second or more. | ·
CAN communication circuit ·
Hybrid vehicle control ECU ·
Skid control ECU (brake booster with master cylinder assembly) |
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Using the GTS, check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Turn the power switch on (IG).
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P163181 is not output | A |
| DTC P163181 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Replace the hybrid vehicle control ECU.
for 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
for M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
Perform the following to make sure that the DTC detection conditions are met.
If the detection conditions are not met, the malfunction cannot be detected.
Turn the power switch on (IG).
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).
Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P163181 is not output | A |
| DTC P163181 is output (for LHD) | B |
| DTC P163181 is output (for RHD) | C |
A
B
C