Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

When the dynamic radar cruise control system is turned on using the cruise control main switch (ON/OFF button), the cruise control indicator (vehicle-to-vehicle distance control mode) illuminates. The hybrid vehicle control ECU uses this and other indicators to indicate the control condition (presence or absence of a preceding vehicle, vehicle-to-vehicle distance, and set vehicle speed) and fail-safe state via CAN communication.

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Meter Display 1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF, 6 to 0 or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. B



A

2.READ VALUE USING GTS (CRUISE READY MAIN-CPU, CRUISE READY SUB-CPU, CRUISE INDICATOR)

B

2.READ VALUE USING GTS (CRUISE READY MAIN-CPU, CRUISE READY SUB-CPU, CRUISE INDICATOR)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON/OFF button) is pushed, ON or OFF changes -
Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch (ON/OFF button) is pushed, ON or OFF changes -
Cruise Indicator Cruise control indicator status ON or OFF ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off
-
Powertrain > Cruise Control > Data List
Tester Display
Cruise Ready Main-CPU
Cruise Ready Sub-CPU
Cruise Indicator
50003 399 25,24,20

Result:
Result Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON/OFF button). A
The cruise control indicator does not illuminate but the Data List item Cruise Indicator changes according to the operation of the cruise control main switch (ON/OFF button). B
The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control main switch (ON/OFF button). (for 2ZR-FXE) C
The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control main switch (ON/OFF button). (for M20A-FXS) D



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C

D