Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0304147 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
·

Removal/installation of the front center ultrasonic sensor

·

Removal/installation of the front corner ultrasonic sensor

·

Replacement of the front center ultrasonic sensor

·

Replacement of the front corner ultrasonic sensor


·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Simple intelligent parking assist system

·

Toyota parking assist-sensor system

·

Parking support brake system


(Click here)

PROCEDURE

Hide 1.REMOVE FRONT BUMPER ASSEMBLY

Hide 89341M 2.REMOVE FRONT SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426314

Disconnect the connector.


b.
E426315

Disengage the claws to remove the front side ultrasonic sensor.


Hide 89341K 3.REMOVE FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426317

Disconnect the connector.


b.
E426318

Disengage the claws to remove the front corner ultrasonic sensor.


Hide 89341L 4.REMOVE FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426320

Disconnect the connector.


b.
E426321

Disengage the claws to remove the front center ultrasonic sensor.


Hide 89347D 5.REMOVE FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)

HINT:
·

Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

·

When removing the front side ultrasonic sensor retainer, heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light.



a.

Heat the front bumper assembly and front side ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Side Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.

Remove the front side ultrasonic sensor retainer.

E426316C01
0.417,0 3.167,1.75 2.75,1.75 3.917,0 6.667,1.75 2.75,1.75 0.5,0.042 0.75,0.281 0.25,0.24 12 true *A 4,0.052 4.25,0.292 0.25,0.24 12 true *B
*A for LH Side *B for RH Side



Hide 52128B 6.REMOVE FRONT BUMPER HOLE COVER LH

HINT:

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>DISASSEMBLY


Hide 52127D 7.REMOVE FRONT BUMPER HOLE COVER RH

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

The following procedure is for the LH side.



Hide 89347B 8.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

When removing the front corner ultrasonic sensor retainer, heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the front bumper assembly and front corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E426319

Remove the front corner ultrasonic sensor retainer.


Hide 89347C 9.REMOVE FRONT CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front center ultrasonic sensor retainer is necessary.

·

When removing the front center ultrasonic sensor retainer, heat the front bumper assembly and front center ultrasonic sensor retainer using a heat light.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Heat the front bumper assembly and front center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Front Bumper Assembly 40 to 60°C (104 to 140°F)
Front Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E426322

Remove the front center ultrasonic sensor retainer.