Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SEAT POSITION SENSOR › from 2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303882 SEAT POSITION SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SEAT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 89178A 1.INSTALL SEAT POSITION AIRBAG SENSOR (for Manual Seat)

a.
B458407C01
0.625,0.729 0.875,0.479 true 2.458,0.75 2.708,0.5 true 2.781,0.385 3.094,0.542 0.313,0.156 10 false *a 0.938,0.375 1.25,0.531 0.313,0.156 10 false *b
*a Pin
*b Installation Hole


Insert the pin into the installation hole and temporarily install the seat position airbag sensor to the seat rail bracket with the "TORX" bolt as shown in the illustration.


b.
B460370C01
0.781,0.594 1.188,1.042 true 2.51,1.115 2.25,1.542 true 0.719,1.917 0.719,1.708 true 0.615,0.458 0.927,0.656 0.313,0.198 10 false *1 2.51,0.896 2.823,1.094 0.313,0.198 10 false *a 3.167,1.5 3.385,1.76 0.219,0.26 10 false *b 0.667,1.948 0.917,2.156 0.25,0.208 10 false *c
*1 Seat Position Airbag Sensor
*a Feeler Gauge
*b 1.3 mm (0.0512 in.)
*c Seat Track Bracket


Using a T30 "TORX" socket wrench and a 1.3 mm (0.0512 in.) feeler gauge, install the seat position airbag sensor with the "TORX" bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
·

If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.

·

When installing the seat position airbag sensor, make sure that the SRS wiring does not interfere with or is pinched between other parts.




c.

Make sure that the clearance between the seat position airbag sensor and seat track bracket is 1.3 mm (0.0512 in.).


d.

Check that there is no looseness in the installed parts of the seat position airbag sensor.


Hide 89178A 2.INSTALL SEAT POSITION AIRBAG SENSOR (for Power Seat)

a.
B471957

Insert the pin into the installation hole.


b.

Using a T30 "TORX" socket wrench, install the seat position airbag sensor to the bracket with the "TORX" bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.



c.
B558595

Using a T30 "TORX" socket wrench, temporarily install the seat position airbag sensor with bracket with the "TORX" bolt.


d.

Make sure that the clearance between the seat position airbag sensor and seat track bracket is 1.3 mm (0.0512 in.).


e.

Check that there is no looseness in the installed parts of the seat position airbag sensor.


f.
B474826C01
0.667,1.208 0.667,1.792 true 1.719,1.292 1.719,1.792 true 0.74,0.365 1,0.365 1,0.365 1.167,0.771 false 0.573,0.292 0.802,0.51 0.229,0.219 10 false *1 0.594,1.792 0.906,1.948 0.313,0.156 10 false *a 2.438,1.292 2.75,1.448 0.313,0.156 10 true *b 1.656,1.792 1.969,1.948 0.313,0.156 10 false *c
*1 Seat Position Airbag Sensor
*a Feeler Gauge
*b 1.3 mm (0.0512 in.)
*c Seat Rail


Using a T30 "TORX" socket wrench and a 1.3 mm (0.0512 in.) feeler gauge, install the seat position airbag sensor with bracket with the "TORX" bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

When installing the seat position airbag sensor with bracket, make sure that the SRS wiring does not interfere with or is not pinched between other parts.



Hide 72277A 3.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR

a.
B458408C01
0.917,0.75 1.25,0.417 true 2.24,0.323 2.49,0.573 true 1.083,1.635 1.333,1.885 true 0.885,1.531 1.052,1.698 0.167,0.167 10 true *a 2.031,0.219 2.344,0.375 0.313,0.156 10 false *b 1.323,0.323 1.635,0.479 0.313,0.156 10 false *c
*a Seat Rail Bracket
*b Pin
*c Installation Part
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the seat slide position sensor protector to the seat rail bracket and engage the pin to the installation part of the seat slide position sensor protector.


b.
B458404

for Manual Seat:

i.

Connect the connector.


ii.

Engage the clamp.



Hide 4.INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 7181B 5.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER (for Power Seat)