Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › 2019.09–2020.08
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0408691 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (B) judges that there is a communication problem with the blind spot monitor sensor RH (A).

DTC No. Detection Item DTC Detection Condition Trouble Area
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor RH (A)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 5 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor LH (B)

·

Power source circuit of blind spot monitor sensor LH (B)

·

Blind spot monitor sensor LH (B) ground circuit

·

Blind spot monitor sensor RH (A)


U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly cannot receive signals from the blind spot monitor sensor LH (B)
·

Open or short in CAN bus main wire or connector

·

Open or short in CAN bus wire or connector

·

Open or short in No. 5 junction connector

·

Clearance warning ECU assembly

·

Blind spot monitor sensor RH (A)

·

Power source circuit of blind spot monitor sensor RH (A)

·

Blind spot monitor sensor RH (A) ground circuit

·

Blind spot monitor sensor LH (B)



WIRING DIAGRAM

E334320E25
5.635,3.438 5.49,3.438 5.49,3.438 4.917,2.354 false 2.479,2.594 3.667,3.021 1.188,0.427 10 false Blind Spot Monitor Sensor RH (A) 3.49,4.156 5.667,4.563 2.177,0.406 10 false Clearance Warning ECU Assembly 5.698,3.542 6.948,3.917 1.25,0.375 10 false No. 6 CAN Junction Connector 3.125,0.948 3.635,1.156 0.51,0.208 10 false CA2P 4.552,3.281 5.24,3.479 0.688,0.198 10 false CANL 3.125,1.781 3.646,2 0.521,0.219 10 false CA2N 4.115,3.281 5.156,3.823 1.042,0.542 10 false CANH 5.563,0.948 6.094,1.125 0.531,0.177 10 false CA2P 5.563,1.792 6.104,1.958 0.542,0.167 10 false CA2N 2.521,1.927 3.01,2.094 0.49,0.167 10 false BRGD 6.146,1.969 6.635,2.177 0.49,0.208 10 false BLGD 6.25,1.229 6.635,1.406 0.385,0.177 10 false BLB 2.521,1.229 3.01,1.438 0.49,0.208 10 false BRB 5.385,0.948 5.531,1.125 0.146,0.177 10 false 1 3.563,0.948 3.708,1.125 0.146,0.177 10 false 1 3.573,1.573 3.719,1.75 0.146,0.177 10 false 6 5.396,1.583 5.542,1.76 0.146,0.177 10 false 6 2.49,2.417 2.854,2.594 0.365,0.177 10 false M63 6.583,1.865 6.927,2.115 0.344,0.25 10 false 10 2.365,1.135 2.51,1.313 0.146,0.177 10 false 5 6.604,1.125 6.75,1.302 0.146,0.177 10 false 5 5.542,2.406 5.885,2.594 0.344,0.188 10 false M62 3.5,3.99 3.865,4.177 0.365,0.188 10 false F142 4.688,3.063 4.969,3.24 0.281,0.177 10 false 38 4.208,3.063 4.469,3.219 0.26,0.156 10 false 37 5.698,3.354 6.146,3.573 0.448,0.219 10 false M104 4,0.948 4.146,1.125 0.146,0.177 10 false 6 4.969,0.948 5.188,1.146 0.219,0.198 10 false 7 4.281,2.417 4.427,2.594 0.146,0.177 10 false 5 4.938,1.583 5.229,1.813 0.292,0.229 10 false 18 4.667,2.417 4.99,2.656 0.323,0.24 10 false 16 3.938,1.573 4.208,1.792 0.271,0.219 10 false 17 2.313,1.823 2.656,2.052 0.344,0.229 10 false 10 1.292,0.625 2.292,0.958 1,0.333 10 false ECU-IG1 NO. 4 0.125,0.49 1.083,0.979 0.958,0.49 10 false from IG1-NO. 1 Relay 5.542,2.573 6.719,2.969 1.177,0.396 10 false Blind Spot Monitor Sensor LH (B) 0.115,0.031 1.625,0.302 1.51,0.271 12 false except TMC Made:

E334320E31
5.635,3.438 5.49,3.438 5.49,3.438 4.917,2.354 false 2.479,2.594 3.667,3.021 1.188,0.427 10 false Blind Spot Monitor Sensor RH (A) 0.156,0.042 1.469,0.344 1.313,0.302 12 false for TMC Made: 5.698,3.542 6.948,3.917 1.25,0.375 10 false No. 6 CAN Junction Connector 3.125,0.948 3.635,1.156 0.51,0.208 10 false CA2P 4.552,3.281 5.24,3.479 0.688,0.198 10 false CANL 3.125,1.781 3.646,2 0.521,0.219 10 false CA2N 4.115,3.281 5.156,3.823 1.042,0.542 10 false CANH 5.563,0.948 6.094,1.125 0.531,0.177 10 false CA2P 5.563,1.792 6.104,1.958 0.542,0.167 10 false CA2N 2.521,1.927 3.01,2.094 0.49,0.167 10 false BRGD 6.146,1.969 6.635,2.177 0.49,0.208 10 false BLGD 6.25,1.229 6.635,1.406 0.385,0.177 10 false BLB 2.521,1.229 3.01,1.438 0.49,0.208 10 false BRB 5.385,0.948 5.531,1.125 0.146,0.177 10 false 1 3.563,0.948 3.708,1.125 0.146,0.177 10 false 1 3.573,1.573 3.719,1.75 0.146,0.177 10 false 6 5.396,1.583 5.542,1.76 0.146,0.177 10 false 6 2.49,2.417 2.854,2.594 0.365,0.177 10 false M63 6.583,1.865 6.927,2.115 0.344,0.25 10 false 10 2.365,1.135 2.51,1.313 0.146,0.177 10 false 5 6.604,1.125 6.75,1.302 0.146,0.177 10 false 5 5.542,2.406 5.885,2.594 0.344,0.188 10 false M62 3.573,4.031 3.938,4.219 0.365,0.188 10 false F142 4.688,3.063 4.969,3.24 0.281,0.177 10 false 38 4.208,3.063 4.469,3.219 0.26,0.156 10 false 37 5.698,3.354 6.146,3.573 0.448,0.219 10 false M104 4,0.948 4.146,1.125 0.146,0.177 10 false 3 4.969,0.948 5.188,1.146 0.219,0.198 10 false 2 4.281,2.417 4.427,2.594 0.146,0.177 10 false 1 4.938,1.583 5.229,1.813 0.292,0.229 10 false 13 4.667,2.417 4.99,2.656 0.323,0.24 10 false 12 3.938,1.573 4.208,1.792 0.271,0.219 10 false 14 2.313,1.823 2.656,2.052 0.344,0.229 10 false 10 1.292,0.625 2.292,0.958 1,0.333 10 false ECU-IG1 NO. 4 0.125,0.49 1.083,0.979 0.958,0.49 10 false from IG1-NO. 1 Relay 5.542,2.573 6.719,2.969 1.177,0.396 10 false Blind Spot Monitor Sensor LH (B) 3.552,4.219 5.823,4.542 2.271,0.323 10 false Clearance Warning ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 is only output A
DTC U117887 is only output B
DTC U117787 and U117887 are output C



A

2.CHECK CAN BUS MAIN WIRE

B

5.CHECK CAN BUS MAIN WIRE

C

8.CHECK CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
2.CHECK CAN BUS MAIN WIRE
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M63 blind spot monitor sensor RH (A) connector.


c.
E359601C56
1.5,0.208 1.885,0.438 0.385,0.229 1,1.667 1.427,1.063 true 1.813,1.635 1.448,1.208 true 1.563,0.25 2.021,0.448 0.458,0.198 10 false M63 0.823,1.667 1.313,1.896 0.49,0.229 10 false CA2P 1.677,1.656 2.167,1.885 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) POWER SOURCE)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CAN BUS MAIN WIRE
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the M62 blind spot monitor sensor LH (B) connector.


c.
E359601C57
1.5,0.208 1.885,0.438 0.385,0.229 0.781,1.698 1.427,1.063 true 1.792,1.667 1.448,1.208 true 1.573,0.25 2.031,0.448 0.458,0.198 10 false M62 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.823,1.594 2.313,1.823 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BODY GROUND)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BODY GROUND)

OK

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) POWER SOURCE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

7.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) POWER SOURCE)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E334331C24
1.542,2.865 1.938,3.115 0.396,0.25 0.229,1.448 0.656,1.708 0.427,0.26 1.823,1.583 2.771,0.938 true 1.823,1.896 2.677,2.5 true 0.969,3.01 1.646,3.417 true 2.354,4 2.667,4.313 true 0.229,2.708 0.542,2.865 0.313,0.156 10 false *1 0.177,0.115 0.49,0.271 0.313,0.156 10 false *a 1.594,2.917 2.01,3.104 0.417,0.188 10 false F144 0.281,1.5 0.667,1.698 0.385,0.198 10 false M104 2.833,0.844 3.417,1.052 0.583,0.208 10 false CANH 2.74,2.427 3.323,2.635 0.583,0.208 10 false CANL 2.719,4.24 3.125,4.458 0.406,0.219 10 false BAT 0.719,2.938 1.302,3.146 0.583,0.208 10 false CG
*1 DLC3
*a Component with harness connected
(No. 6 CAN Junction Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M104-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
M104-16 (CANL) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
M104-5 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M104-16 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

9.CONFIRM CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)

B

11.CHECK FOR OPEN IN CAN BUS WIRE (No. 6 CAN JUNCTION CONNECTOR)

C

15.CHECK FOR SHORT IN CAN BUS WIRES (No. 6 CAN JUNCTION CONNECTOR)

D

19.CHECK FOR SHORT IN CAN BUS WIRES (No. 6 CAN JUNCTION CONNECTOR)
9.CONFIRM CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the F142 clearance warning ECU assembly connector.


b.
C398226C15
1.49,0.302 1.917,0.542 0.427,0.24 1.323,1.771 2.542,1.177 true 2.677,1.688 2.677,1.188 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.563,0.344 2.177,0.542 0.615,0.198 10 false F142 0.885,1.708 1.344,1.969 0.458,0.26 10 false CANH 2.531,1.719 2.99,1.979 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F142-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

10.CHECK DTC

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 19 JUNCTION CONNECTOR)

10.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

b.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 and U117887 are output A
DTC U117787 and U117887 are not output B



A

B

11.CHECK FOR OPEN IN CAN BUS WIRE (No. 6 CAN JUNCTION CONNECTOR)
a.
E331799C51
1.469,0.677 1.885,0.917 0.417,0.24 1.719,1.823 2.74,0.719 true 1.927,1.833 2.719,0.948 true 1.5,1.833 2.74,0.49 true 1.729,2.75 1.729,2.177 true 2.438,2.75 1.927,2.146 true 1.104,2.781 1.51,2.167 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.521,0.708 1.979,0.906 0.458,0.198 10 false M104 2.792,0.854 3.406,1.052 0.615,0.198 10 false CANH*b 2.792,0.625 3.406,0.823 0.615,0.198 10 false CANH*c 0.552,2.719 1.167,2.917 0.615,0.198 10 false CANL*b 1.531,2.771 2.146,2.969 0.615,0.198 10 false CANL*c 2.792,0.385 3.406,0.583 0.615,0.198 10 false CANH*d 2.5,2.667 3.115,2.865 0.615,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH (B) CAN Main Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire
*d to Clearance Warning ECU Assembly CAN Wire


Disconnect the M104 No. 6 CAN Junction Connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M104-6 (CANH) - M104-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M104-7 (CANH) - M104-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to Blind Spot Monitor Sensor LH (B) CAN Main Wire) B
NG (to Blind Spot Monitor Sensor RH (A) CAN Main Wire) C
NG (to Clearance Warning ECU Assembly CAN Wire) D



A

REPLACE No. 19 JUNCTION CONNECTOR

B

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

C

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

D

14.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
E359601C58
1.5,0.208 1.885,0.438 0.385,0.229 0.792,1.677 1.417,1.063 true 1.875,1.958 1.438,1.208 true 1.563,0.25 2.021,0.448 0.458,0.198 10 false M62 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.927,1.885 2.417,2.115 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the M62 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
E359601C59
1.5,0.208 1.917,0.448 0.417,0.24 1.969,1.781 1.438,1.208 true 0.781,1.677 1.427,1.063 true 1.594,0.25 2.052,0.448 0.458,0.198 10 false M63 0.396,1.615 0.885,1.844 0.49,0.229 10 false CA2P 2.01,1.708 2.5,1.938 0.49,0.229 10 false CA2N 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the M63 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - No. 19 JUNCTION CONNECTOR)

14.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
C398226C16
1.49,0.302 1.917,0.542 0.427,0.24 1.979,1.729 2.563,1.188 true 3.073,1.729 2.677,1.188 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.781,1.76 2.24,2.021 0.458,0.26 10 false CANH 2.927,1.76 3.385,2.021 0.458,0.26 10 false CANL 1.552,0.344 2.01,0.604 0.458,0.26 10 false F142
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the F142 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F142-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 19 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (No. 6 CAN JUNCTION CONNECTOR)
a.
E331799C51
1.469,0.677 1.885,0.917 0.417,0.24 1.719,1.823 2.74,0.719 true 1.927,1.833 2.719,0.948 true 1.5,1.833 2.74,0.49 true 1.729,2.75 1.729,2.177 true 2.438,2.75 1.927,2.146 true 1.104,2.781 1.51,2.167 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.521,0.708 1.979,0.906 0.458,0.198 10 false M104 2.792,0.854 3.406,1.052 0.615,0.198 10 false CANH*b 2.792,0.625 3.406,0.823 0.615,0.198 10 false CANH*c 0.552,2.719 1.167,2.917 0.615,0.198 10 false CANL*b 1.531,2.771 2.146,2.969 0.615,0.198 10 false CANL*c 2.792,0.385 3.406,0.583 0.615,0.198 10 false CANH*d 2.5,2.667 3.115,2.865 0.615,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH (B) CAN Main Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire
*d to Clearance Warning ECU Assembly CAN Wire


Disconnect the M104 No. 6 CAN Junction Connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M104-6 (CANH) - M104-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M104-7 (CANH) - M104-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M104-5 (CANH) - M104-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (Blind Spot Monitor Sensor LH (B) CAN Main Wire) B
NG (to Blind Spot Monitor Sensor RH (A) CAN Main Wire) C
NG (to Clearance Warning ECU Assembly CAN Wire) D



A

REPLACE No. 19 JUNCTION CONNECTOR

B

16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

18.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
16.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
E359601C63
1.5,0.208 1.885,0.438 0.385,0.229 0.771,1.677 1.427,1.042 true 1.948,1.667 1.438,1.198 true 0.365,1.604 0.854,1.833 0.49,0.229 10 false CA2P 1.99,1.594 2.479,1.823 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.573,0.25 2.063,0.479 0.49,0.229 10 false M62
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the M62 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - M62-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
E359601C60
1.5,0.208 1.885,0.438 0.385,0.229 0.781,1.667 1.427,1.073 true 1.885,1.698 1.438,1.208 true 1.573,0.25 2.031,0.448 0.458,0.198 10 false M63 0.365,1.615 0.854,1.844 0.49,0.229 10 false CA2P 1.948,1.625 2.438,1.854 0.49,0.229 10 false CA2N 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the M63 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - M63-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - No. 19 JUNCTION CONNECTOR)

18.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
C398226C17
1.49,0.302 1.917,0.542 0.427,0.24 2.333,1.667 2.563,1.188 true 2.948,1.667 2.677,1.177 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 1.563,0.354 2.177,0.552 0.615,0.198 10 false F142 2.146,1.688 2.604,1.948 0.458,0.26 10 false CANH 2.813,1.688 3.271,1.948 0.458,0.26 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the F142 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F142-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 19 JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (No. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the M104 No. 6 CAN Junction Connector.


b.

Measure the resistance according to the value(s) in the table below.

E348217C14
1.99,0.49 2.438,0.75 0.448,0.26 5.479,0.479 5.927,0.74 0.448,0.26 6.479,2.208 6.479,1.802 true 5.365,2.167 5.76,1.406 true 0.969,0.979 1.885,1.5 true 2.25,2.135 2.208,1.719 true 2.052,1.698 1.49,2.146 true 1.135,0.354 2.198,1.521 true 2.979,0.625 2.344,1.5 true 2.365,1.698 2.917,2.167 true 4.646,0.521 4.958,0.677 0.313,0.156 10 false *1 0.104,0.25 0.417,0.406 0.313,0.156 10 false *a 0.427,0.917 1.094,1.156 0.667,0.24 10 false CANH*c 0.583,0.271 1.146,0.531 0.563,0.26 10 false CANH*d 3.031,0.542 3.667,0.781 0.635,0.24 10 false CANH*b 2.063,0.542 2.521,0.74 0.458,0.198 10 false M104 5.563,0.531 6.094,0.74 0.531,0.208 10 false F144 6.365,2.25 6.792,2.469 0.427,0.219 10 false BAT 5.25,2.198 5.521,2.406 0.271,0.208 10 false CG 2.74,2.198 3.406,2.438 0.667,0.24 10 false CANL*b 1.229,2.188 1.792,2.448 0.563,0.26 10 false CANL*d 2.042,2.188 2.677,2.427 0.635,0.24 10 false CANL*c
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH (B) CAN Main Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire *d to Clearance Wwarning ECU Assembly CAN Wire


Standard Resistance:
Tester Connection Condition Specified Condition
M104-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-17 (CANL) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-6 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M104-17 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M104-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-16 (CANL) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-5 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M104-16 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M104-7 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-18 (CANL) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-7 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M104-18 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to Blind Spot Monitor Sensor LH (B) CAN Main Wire) B
NG (to Blind Spot Monitor Sensor RH (A) CAN Main Wire) C
NG (to Clearance Warning ECU Assembly CAN Wire) D



A

REPLACE No. 19 JUNCTION CONNECTOR

B

20.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

22.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
20.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.

Disconnect the M62 blind spot monitor sensor LH (B) connector.


c.
E415772C01
1.51,1.802 1.906,2.094 0.396,0.292 1.469,0.25 1.865,0.542 0.396,0.292 0.74,0.771 1.406,1.042 true 0.75,1.479 1.406,1.24 true 1.115,1.948 1.635,2.365 true 2.26,2.833 2.604,3.042 true 0.5,1.896 0.813,2.052 0.313,0.156 10 false *1 0.177,0.198 0.49,0.354 0.313,0.156 10 false *a 1.573,1.875 1.948,2.073 0.375,0.198 10 false F144 1.542,0.323 1.906,0.521 0.365,0.198 10 false M62 0.354,0.708 0.969,0.906 0.615,0.198 10 false CA2P 0.354,1.417 0.969,1.615 0.615,0.198 10 false CA2N 2.646,2.958 3.26,3.156 0.615,0.198 10 false BAT 0.865,1.875 1.479,2.073 0.615,0.198 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M62-1 (CA2P) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M62-6 (CA2N) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M62-1 (CA2P) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M62-6 (CA2N) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - No. 19 JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.

Reconnect the M104 No. 19 junction connector.


b.

Disconnect the M63 blind spot monitor sensor RH (A) connector.


c.
E415772C02
1.49,0.281 1.854,0.563 0.365,0.281 1.521,1.781 1.938,2.063 0.417,0.281 0.865,0.573 1.406,1.042 true 0.885,1.385 1.406,1.229 true 0.99,1.948 1.635,2.375 true 2.646,2.969 2.271,2.813 true 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a 1.542,0.344 1.906,0.542 0.365,0.198 10 false M63 1.583,1.833 2.01,2.042 0.427,0.208 10 false F144 0.469,0.49 0.938,0.688 0.469,0.198 10 false CA2P 0.479,1.323 0.948,1.521 0.469,0.198 10 false CA2N 0.75,1.865 1.219,2.063 0.469,0.198 10 false CG 2.698,2.906 3.167,3.104 0.469,0.198 10 false BAT
*1 DLC3
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M63-1 (CA2P) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M63-6 (CA2N) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M63-1 (CA2P) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
M63-6 (CA2N) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - No. 19 JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.

Reconnect the M104 No. 6 CAN Junction Connector.


b.
E348218C12
1.406,0.302 1.771,0.563 0.365,0.26 1.542,1.823 1.906,2.083 0.365,0.26 2.323,1.719 2.479,1.26 true 2.833,1.698 2.583,1.25 true 1.344,3.146 1.635,2.5 true 2.24,2.823 2.552,3.135 true 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 0.198,2.031 0.51,2.229 0.313,0.198 10 false *1 1.438,0.354 1.813,0.531 0.375,0.177 10 false F142 1.573,1.875 2.031,2.073 0.458,0.198 10 false F144 2.146,1.729 2.552,1.958 0.406,0.229 10 false CANL 2.688,1.729 3.094,1.958 0.406,0.229 10 false CANH 2.438,3.146 2.844,3.375 0.406,0.229 10 false BAT 1.24,3.156 1.646,3.385 0.406,0.229 10 false CG
*1 DLC3
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the F142 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-37 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F142-38 (CANL) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F142-37 (CANH) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F142-38 (CANL) - F144-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - No. 19 JUNCTION CONNECTOR)