Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0303371 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  No. 2 Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 2 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E427838E02
1.979,1.354 2.104,1.583 0.125,0.229 10 false 1 3.271,1.354 3.448,1.583 0.177,0.229 10 false 2 1.635,2.021 1.969,2.25 0.333,0.229 10 false F55 1.635,2.188 3.74,2.542 2.104,0.354 10 false No. 2 Clearance Warning Buzzer 4.198,2.021 4.781,2.25 0.583,0.229 10 false F142 4.188,2.188 6.448,2.5 2.26,0.313 10 false Clearance Warning ECU Assembly 4.677,0.583 4.917,0.781 0.24,0.198 10 false 25 4.948,0.708 5.479,1.01 0.531,0.302 10 false BBZ 4.948,1.438 5.229,1.677 0.281,0.24 10 false ER 2.135,1.354 2.385,1.615 0.25,0.26 10 false Z+ 3.063,1.354 3.24,1.573 0.177,0.219 10 false Z- 4.677,1.323 4.917,1.521 0.24,0.198 10 false 26

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Warning / Active Test.


e.

Check that the rear buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Buzzer No. 2 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > Clearance Warning > Active Test
Tester Display
Rear Buzzer
50004 438 2
OK:

The No. 2 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)
a.

Disconnect the F142 clearance warning ECU assembly connector.


b.

Disconnect the F55 No. 2 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F142-25 (BBZ) - F55-1 (Z+) Always Below 1 Ω
F142-26 (ER) - F55-2 (Z-) Always Below 1 Ω
F142-25 (BBZ) or F55-1 (Z+) - Body ground Always 10 kΩ or higher
F142-26 (ER) or F55-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 2 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 2 CLEARANCE WARNING BUZZER
a.

Replace the No. 2 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Warning / Active Test.


e.

Check that the rear buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Buzzer No. 2 clearance warning buzzer Stop or Operate Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > Clearance Warning > Active Test
Tester Display
Rear Buzzer
50004 438 2
OK:

The No. 2 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (NO. 2 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG