Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › SIMPLE INTELLIGENT PARKING ASSIST SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0303239 SIMPLE INTELLIGENT PARKING ASSIST SYSTEM D

PARK ASSIST / MONITORING  SIMPLE INTELLIGENT PARKING ASSIST SYSTEM  CALIBRATION  


NOTICE:

When any of the following parts have been replaced, perform adjustment shown in the following table. If not, the simple intelligent parking assist system may not operate correctly.


PRECAUTION (PROCEDURE 1)


a.

w/ Parking Support Brake System

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during simple intelligent parking assist system removal/installation are shown below.

For the installation location of the ultrasonic sensors, refer to Parts Location.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>PARTS LOCATION

Part Name Operation Adjustment Item Proceed to
Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize parking support brake system) (Click here)
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Ultrasonic sensor detection angle
Ultrasonic sensor detection angle registration
Front bumper assembly
·

Replacement

·

Installation position of the front bumper cover changes because of the removal and installation of the front bumper cover


Ultrasonic sensor detection angle
Ultrasonic sensor detection angle registration
Rear bumper assembly
·

Replacement

·

Installation position of the rear bumper cover changes because of the removal and installation of the rear bumper cover


Ultrasonic sensor detection angle
Ultrasonic sensor detection angle registration
Clearance warning ECU assembly Replacement Ultrasonic sensor detection angle
Bumper type registration
Ultrasonic sensor detection angle registration
Steering angle neutral point
Ultrasonic sensor*1*2
·

Removal and installation

·

Replacement


Ultrasonic sensor detection angle
Ultrasonic sensor detection angle registration
An ultrasonic sensor becomes misaligned Ultrasonic sensor detection angle
Ultrasonic sensor detection angle registration
An ultrasonic sensor is subjected to impact Ultrasonic sensor detection angle
Ultrasonic sensor detection angle registration
Auxiliary battery Cable is disconnected from the negative (-) auxiliary battery terminal Steering angle neutral point

*1: If a front side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform Registration.

*2: If a rear side ultrasonic sensor (LH, RH) is removed and installed or replaced, it is necessary to perform Registration.



b.

w/o Parking Support Brake System

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during simple intelligent parking assist system removal/installation are shown below.

For the installation location of the ultrasonic sensors, refer to Parts Location.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>PARTS LOCATION

Part Name Operation Adjustment Item Proceed to
Steering sensor
·

Removal and installation of the steering sensor

·

Removal and installation of the connector of the steering sensor

·

Replacement


Steering angle neutral point (Initialize simple intelligent parking assist system)* Procedure 2
Clearance warning ECU assembly Replacement Steering angle neutral point Procedure 2
Bumper type registration
Auxiliary battery Disconnect the cable from the negative (-) battery terminal, or remove the fuse for the TOYOTA parking assist-sensor system, etc. ("Memory Error" is displayed on the multi-information display) Steering angle neutral point* Procedure 2

*: The steering sensor zero point can also be calibrated by driving the vehicle.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>INITIALIZATION




REGISTRATION (PROCEDURE 2)


a.

Preparation

i.

Confirm that the following DTCs are not output.

System Proceed to
Simple Intelligent Parking Assist System (Click here)
TOYOTA parking assist-sensor system (Click here)

NOTICE:

If DTC C1AE087, C1AE187, C1AE287, C1AE387, C1AE487, C1AE587, C1AE687, C1AE787, C1AE887, C1AE987, C1AF187 or C1AF287 are output, continue with the registration procedure.




b.

Connect the GTS to the DLC3.


c.

Check that the steering wheel is centered (approximately +/- 5 degrees or less).

NOTICE:

Make sure that the wheels are positioned straight ahead.



d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Clearance Warning / Utility.

Body Electrical > Clearance Warning > Utility
Tester Display
ECU Calibration
50005 438 2535

f.

According to the display on the GTS, perform calibration.


g.

w/ Parking Support Brake System

Enter the bumper type using the GTS.

Bumper Type Value
for 2ZR-FXE 1
for M20A-FXS 2

HINT:

If the clearance warning ECU assembly is replaced or removed and installed, it is necessary to perform bumper type registration.



h.

w/o Parking Support Brake System

Enter the bumper type using the GTS.

Bumper Type Value
Standard 2

HINT:

If the clearance warning ECU assembly is replaced or removed and installed, it is necessary to perform bumper type registration.



i.

Disconnect the GTS from the DLC3.