Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0299417 IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  B2784  Antenna Coil Open / Short  


DESCRIPTION

When an open or short circuit is detected in the transponder key amplifier coil built into the power switch, the certification ECU (smart key ECU assembly) stores this DTC. This DTC is also stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2784 Antenna Coil Open / Short The transponder key amplifier coil built into the power switch is open (see below) or shorted (determined by communication with certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Terminal AGND, VC5, TXCT or CODE circuit is open (including disconnection of the power switch).

·

The transponder key amplifier coil built into the power switch is open.


·

Power switch

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)


DTC output confirmation operation:

With the shift lever in P and the electrical key transmitter sub-assembly held near the power switch, a hybrid control system start operation is performed by pressing and holding the power switch when the transmitter battery is depleted.



*: Only output while a malfunction is present.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Always ○ ○
Malfunction Status The transponder key amplifier coil built into the power switch is open (determined by communication with certification ECU (smart key ECU assembly)). ○ -
The transponder key amplifier coil built into the power switch is shorted (determined by communication with certification ECU (smart key ECU assembly)). - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started when transmitter battery is depleted by holding electrical key transmitter sub-assembly near power switch and pressing and holding power switch with shift lever in P -

Related Data List and Active Test
DTC No. Data List and Active Test
B2784 -

WIRING DIAGRAM

E305785E37
1.531,0.792 2.052,1.25 0.521,0.458 10 false VC5 1.906,0.677 2.427,1.135 0.521,0.458 10 false 10 1.479,1.313 2,1.771 0.521,0.458 10 false TXCT 1.406,1.729 1.927,2.188 0.521,0.458 10 false CODE 1.938,1.208 2.458,1.667 0.521,0.458 10 false 7 1.938,1.719 2.458,2.177 0.521,0.458 10 false 8 1.938,2.229 2.458,2.688 0.521,0.458 10 false 6 1.417,2.24 1.938,2.698 0.521,0.458 10 false AGND 0.573,3.063 0.917,3.24 0.344,0.177 10 false F59 0.573,3.208 2.01,3.417 1.438,0.208 10 false Power Switch 5.031,0.677 5.552,1.135 0.521,0.458 10 false 7 5.042,1.198 5.563,1.656 0.521,0.458 10 false 5 5.042,1.708 5.563,2.167 0.521,0.458 10 false 6 4.99,2.219 5.51,2.677 0.521,0.458 10 false 11 5.688,0.302 6.208,0.76 0.521,0.458 10 false 5 V 5.302,3.031 5.823,3.49 0.521,0.458 10 false F1 5.302,3.188 6.833,3.552 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.26,0.688 5.781,1.146 0.521,0.458 10 false VC5 5.26,1.198 5.781,1.656 0.521,0.458 10 false TXCT 5.25,1.708 5.771,2.167 0.521,0.458 10 false CODE 5.25,2.219 5.771,2.677 0.521,0.458 10 false AGND 6.156,1.531 6.677,1.99 0.521,0.458 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK POWER SWITCH (OUTPUT)
3.CHECK POWER SWITCH (OUTPUT)
a.

Using an oscilloscope, check the waveform.

B363541C35
1.458,0.958 1.813,1.177 0.354,0.219 1.344,2.896 1.635,2.896 1.635,2.896 1.635,2.156 true 2.198,2.896 1.875,2.896 1.875,2.896 1.875,2.156 true 0.74,1.083 1.052,1.24 0.313,0.156 10 false *a 3.385,0.281 3.698,0.438 0.313,0.156 10 false *b 3.406,2.052 3.719,2.208 0.313,0.156 10 false *c 6.49,1.333 7.031,1.563 0.542,0.229 10 false GND 6.49,3.115 7.031,3.344 0.542,0.229 10 false GND 2.26,2.813 2.802,3.042 0.542,0.229 10 false AGND 0.917,2.823 1.458,3.052 0.542,0.229 10 false CODE 1.531,0.979 2.073,1.208 0.542,0.229 10 false F59
*a Component with harness connected
(Power Switch)
*b Waveform
*c Waveform (detail) - -


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
F59-8 (CODE) - F59-6 (AGND) Power switch off, power switch pressed with electrical key transmitter sub-assembly held near power switch* 1 V/DIV., 20 ms./DIV. Pulse generation
(See waveform)
2 V/DIV., 100 μs./DIV. Pulse generation
(See waveform (detail))


*: Remove the transmitter battery before performing this inspection.


OK:

The waveform is similar to that shown in the illustration



Result:
Result Proceed to
OK A
NG (for LHD with 2ZR-FXE) B
NG (for RHD with 2ZR-FXE) C
NG (for LHD with M20A-FXS) D
NG (for RHD with M20A-FXS) E



A

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

D

E

4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.


OK:

DTC B2784 is not output.



Result:
Result Proceed to
OK A
NG (for LHD with 2ZR-FXE) B
NG (for RHD with 2ZR-FXE) C
NG (for LHD with M20A-FXS) D
NG (for RHD with M20A-FXS) E



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

D

E