CHECK DLC3
Check the DLC3.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION
FUNCTION OF SRS WARNING LIGHT
Primary check
Turn the power switch off. Wait for at least 2 seconds, then turn the power switch on (IG). The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.
If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.
Constant check
After the primary check, the airbag sensor assembly constantly monitors the airbag system for malfunctions.
The SRS warning light comes on.
The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.
Review
When the airbag system is normal:
The SRS warning light comes on only during the primary check period of approximately 6 seconds after the power switch is turned on (IG).
When the airbag system is malfunctioning:
The SRS warning light remains on even after the primary check period.
The SRS warning light goes off after the primary check, but comes on again during the constant check.
The SRS warning light does not come on when the power switch is turned from off to on (IG).
The SRS warning light will remain illuminated if any airbag or pretensioner has been deployed.
SRS WARNING LIGHT CHECK
Turn the power switch on (IG), and check that the SRS warning light comes on for approximately 6 seconds (primary check).
Check that the SRS warning light goes off approximately 6 seconds after the power switch is turned on (IG) (constant check).
When any of the following symptoms occur, refer to Problem Symptoms Table.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE
The SRS warning light comes on occasionally after the primary check period.
The SRS warning light comes on, but DTCs are not output.
The power switch is turned from off to on (IG), but the SRS warning light does not come on.
FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cut Off Switch)
Initial check
Turn the power switch on (IG).
The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, then turns off for approximately 2 seconds.
Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF according to the airbag cut off switch cylinder sub-assembly condition as listed below.
| Airbag Cut Off Switch Cylinder Sub-assembly Condition | Passenger Airbag ON/OFF Indicator | SRS Warning Light | |
|---|---|---|---|
| ON Indicator | OFF Indicator | ||
|
*1: The ON indicator illuminates for approximately 60 seconds and then turns off. |
|||
| ON | ON*1 | OFF | OFF |
| OFF | OFF | ON | OFF |
| Switch failure | OFF | ON | ON |
If the SRS warning light is not illuminated and the passenger airbag ON/OFF indicator does not operate as specified in the table according to the airbag cut off switch cylinder sub-assembly status, no related DTCs will be stored. Proceed to the Trouble in Passenger Airbag ON/OFF Indicator troubleshooting procedure.
PASSENGER AIRBAG ON/OFF INDICATOR CHECK (w/ Airbag Cut Off Switch)
Turn the power switch on (IG).
Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, then goes off for approximately 2 seconds.
Refer to the indicator operation table in Function of Passenger Airbag ON/OFF Indicator for the passenger airbag ON/OFF indicator operation when the power switch is turned on (IG) and approximately 6 seconds elapse.
FUNCTION OF SRS CONNECTORS
Location of activation prevention mechanism
Function of activation prevention mechanism
This mechanism is designed to create a short circuit automatically between the positive (+) and negative (-) terminals of an airbag power source connector when disconnected.
The short spring plate contained in the connector creates a closed circuit on the squib side (no potential difference can occur between both terminals), preventing accidental squib deployment when servicing.
Releasing of activation prevention mechanism
To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.
Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.
Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.
Do not release the activation prevention mechanism unless specified by the troubleshooting procedure.
To prevent the terminals and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.