Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2019.09–2022.01
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1647  Side Satellite Sensor Bus Lost Communication (LH)  B1648  Side Satellite Sensor Bus Initialization Error (LH)  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor LH.

The door side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1647 Side Satellite Sensor Bus Lost Communication (LH)
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1648 Side Satellite Sensor Bus Initialization Error (LH)
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1).

·

No. 2 side airbag sensor LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

No. 2 side airbag sensor LH

·

Door side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B1647):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1647):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status No. 2 side airbag sensor LH malfunction ○ - -
Door side airbag sensor LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1648):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) ○ - - -
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) - ○ - -
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) - - ○ -
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1648):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status No. 2 side airbag sensor LH malfunction ○ - -
Door side airbag sensor LH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C398356E04
4.865,2 6.729,2.24 1.865,0.24 10 false Airbag Sensor Assembly 4.875,1.823 5.417,1.99 0.542,0.167 10 false M102 5.375,0.906 6,1.229 0.625,0.323 10 false Interface 1.833,2.521 2.458,2.844 0.625,0.323 10 false Interface 5.083,3.219 5.75,3.49 0.667,0.271 10 false Interface 0.927,2.51 1.563,2.802 0.635,0.292 10 false Element 6.021,3.229 6.656,3.521 0.635,0.292 10 false Element 4.813,0.51 5.531,0.667 0.719,0.156 10 false BBL+ 4.833,1.188 5.417,1.333 0.583,0.146 10 false BBL- 4.552,0.5 5.135,0.865 0.583,0.365 10 false 32 4.542,1.177 4.927,1.417 0.385,0.24 10 false 31 2.552,0.51 2.99,0.75 0.438,0.24 10 false BCL+ 3.021,0.51 3.333,0.75 0.313,0.24 10 false 4 2.583,1.167 3.073,1.333 0.49,0.167 10 false BCL- 3.031,1.177 3.333,1.396 0.302,0.219 10 false 3 2.573,2.781 3.073,2.99 0.5,0.208 10 false BDL+ 3.021,2.771 3.271,2.969 0.25,0.198 10 false 1 2.594,3.458 3.083,3.656 0.49,0.198 10 false BDL- 3.031,3.458 3.281,3.656 0.25,0.198 10 false 2 3.594,2.875 4.031,3.094 0.438,0.219 10 false JM1 3.583,3.552 3.938,3.792 0.354,0.24 10 false JM1 3.656,2.677 4.042,2.833 0.385,0.156 10 false 22 3.656,3.365 3.885,3.552 0.229,0.188 10 false 40 4.354,2.781 4.667,3 0.313,0.219 10 false 2 4.365,3.458 4.656,3.667 0.292,0.208 10 false 1 4.542,2.792 5.25,2.99 0.708,0.198 10 false BDL+ 4.542,3.469 5.115,3.677 0.573,0.208 10 false BDL- 0.708,4.125 2.375,4.49 1.667,0.365 10 false M15 0.698,4.271 3.25,4.583 2.552,0.313 10 false No. 2 Side Airbag Sensor LH 4.542,4.125 5.021,4.333 0.479,0.208 10 false J5 4.542,4.292 6.656,4.552 2.115,0.26 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

3.CHECK FLOOR WIRE
a.
B474703C19
0.75,0.844 1.167,1.083 0.417,0.24 0.833,3.75 1.198,3.99 0.365,0.24 2.125,1.802 2.125,1.677 false 1.74,1.708 2.073,1.292 true 2.552,1.708 2.188,1.292 true 1.635,2.927 1.635,2.51 false 2.354,4.271 2.042,3.854 true 1.646,4.271 1.917,3.854 true 0.729,2.375 1.167,2.792 0.438,0.417 10 false *1 2.531,2.656 2.958,3.083 0.427,0.427 10 false *2 1.563,2.938 1.99,3.313 0.427,0.375 10 false *3 2.073,1.823 2.604,2.292 0.531,0.469 10 false *4 0.667,0.198 1.313,0.792 0.646,0.594 10 false *a 0.708,3.438 1.167,3.854 0.458,0.417 10 false *b 2.188,2.385 2.615,2.813 0.427,0.427 10 false A 1.885,2.385 2.313,2.813 0.427,0.427 10 false B 1.292,2.375 1.719,2.802 0.427,0.427 10 false C 0.979,2.375 1.406,2.802 0.427,0.427 10 false D 0.792,0.875 1.229,1.229 0.438,0.354 10 false M102 0.896,3.781 1.323,4.208 0.427,0.427 10 false M15 2.427,1.708 2.979,2.188 0.552,0.479 10 false BBL+ 1.594,1.719 2.771,2.146 1.177,0.427 10 false BBL- 2.219,4.281 2.771,4.542 0.552,0.26 10 false BCL+ 1.5,4.281 2.052,4.542 0.552,0.26 10 false BCL-
*1 No. 2 Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M15-4 (BCL+) - Body ground Power switch on (IG) Below 1 V
M15-3 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-4 (BCL+) - M15-3 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-4 (BCL+) - M15-3 (BCL-) Always 1 MΩ or higher
M15-4 (BCL+) - Body ground Always 1 MΩ or higher
M15-3 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE

4.CHECK WIRE HARNESS
a.
C295812C47
0.844,0.635 1.229,0.865 0.385,0.229 0.552,3.615 0.885,3.833 0.333,0.219 1.958,2.854 1.958,2.469 false 2.052,4.167 1.656,3.76 true 1.531,4.365 1.531,4.219 false 1.448,1.24 1.76,0.781 true 2.219,1.24 1.938,0.781 true 1.448,2.344 1.448,1.771 1.448,1.771 1.271,1.771 false 0.938,4.156 1.375,3.75 true 0.552,2.333 1.042,2.781 0.49,0.448 10 false *1 2.719,2.333 3.208,2.802 0.49,0.469 10 false *2 1.469,4.365 1.854,4.646 0.385,0.281 10 false *5 0.635,0.177 1.073,0.656 0.438,0.479 10 false *a 0.354,3.167 0.792,3.813 0.438,0.646 10 false *b 2.385,2.333 2.875,2.802 0.49,0.469 10 false A 2.083,2.333 2.573,2.802 0.49,0.469 10 false B 1.74,2.333 2.229,2.802 0.49,0.469 10 false C 1.583,2.333 2.073,2.802 0.49,0.469 10 false D 1.229,2.333 1.719,2.802 0.49,0.469 10 false E 0.927,2.333 1.417,2.802 0.49,0.469 10 false F 1.302,1.25 1.844,1.521 0.542,0.271 10 false BDL+ 2.135,1.25 2.802,1.667 0.667,0.417 10 false BDL- 2.01,4.177 2.51,4.646 0.5,0.469 10 false BDL+ 0.698,4.167 1.198,4.5 0.5,0.333 10 false BDL- 0.917,0.667 1.458,0.938 0.542,0.271 10 false M15 0.635,3.646 1.177,3.917 0.542,0.271 10 false J5 1.063,1.698 1.563,2.031 0.5,0.333 10 false *3 1.896,2.875 2.396,3.208 0.5,0.333 10 false *4
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M15-1 (BDL+) - Body ground Power switch on (IG) Below 1 V
M15-2 (BDL-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-1 (BDL+) - M15-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-1 (BDL+) - M15-2 (BDL-) Always 1 MΩ or higher
M15-1 (BDL+) - Body ground Always 1 MΩ or higher
M15-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 SIDE AIRBAG SENSOR LH

NG

7.CHECK FLOOR WIRE
5.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connectors to the door side airbag sensor LH and airbag sensor assembly.


b.

Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647 or B1648 is output. A
DTC B1642 or B1643 is output. B
DTCs B1642, B1643, B1647 and B1648 are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

6.CHECK DOOR SIDE AIRBAG SENSOR LH

B

C

6.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1643, B1647 and B1648 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647 or B1648 is output. A
DTC B1642 or B1643 is output. B
DTCs B1642, B1643, B1647 and B1648 are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

7.CHECK FLOOR WIRE
a.
C284681C72
0.865,0.563 1.219,0.792 0.354,0.229 0.458,2.823 0.823,3.042 0.365,0.219 2,2.927 1.406,3.573 true 1.844,1.281 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.333,1.167 1.917,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 2.01,4.344 1.396,3.792 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.688,1.708 1.896,2.042 0.208,0.333 10 false *4 1.781,1.302 2.198,1.625 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.063,1.188 1.563,1.521 0.5,0.333 10 false BDL+ 2.302,1.198 2.802,1.531 0.5,0.333 10 false BDL- 2.083,4.25 2.583,4.5 0.5,0.25 10 false BDL- 2.083,2.844 2.667,3.083 0.583,0.24 10 false BDL+ 0.917,0.594 1.417,0.927 0.5,0.333 10 false M15 0.51,2.844 1.01,3.094 0.5,0.25 10 false JM1
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Front Door Wire LH)


Disconnect the floor wire connector from the front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
JM1-22 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM1-40 (BDL-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM1-22 (BDL+) - JM1-40 (BDL-) Always 1 MΩ or higher
JM1-22 (BDL+) - Body ground Always 1 MΩ or higher
JM1-40 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE