Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2019.09–2022.01
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B166D  Lost Communication with Front Door Pressure Sensor RH  B166E  Front Door Pressure Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor RH.

The door side airbag sensor RH and No. 2 side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B166D Lost Communication with Front Door Pressure Sensor RH
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B166E Front Door Pressure Sensor RH Initialization Incomplete
·

The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1).

·

No. 2 side airbag sensor RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

No. 2 side airbag sensor RH

·

Door side airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B166D):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B166D):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status No. 2 side airbag sensor RH malfunction ○ - -
Door side airbag sensor RH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B166E):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) ○ - - -
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) - ○ - -
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) - - ○ -
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B166E):
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status No. 2 side airbag sensor RH malfunction ○ - -
Door side airbag sensor RH malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C398356E03
4.792,1.99 6.458,2.354 1.667,0.365 10 false Airbag Sensor Assembly 4.792,1.823 6.458,2.188 1.667,0.365 10 false M103 5.354,0.948 5.979,1.271 0.625,0.323 10 false Interface 1.813,2.042 2.438,2.365 0.625,0.323 10 false Interface 5.083,3.229 5.823,3.521 0.74,0.292 10 false Interface 0.875,2.521 1.5,2.885 0.625,0.365 10 false Element 6.01,3.229 6.646,3.521 0.635,0.292 10 false Element 4.792,0.51 5.5,0.823 0.708,0.313 10 false BBR+ 4.792,1.177 6.458,1.542 1.667,0.365 10 false BBR- 4.552,0.51 5.135,0.875 0.583,0.365 10 false 25 4.552,1.177 6.219,1.542 1.667,0.365 10 false 26 2.531,0.5 4.198,0.865 1.667,0.365 10 false BCR+ 3.01,0.5 3.385,0.74 0.375,0.24 10 false 4 2.563,1.177 3.083,1.49 0.521,0.313 10 false BCR- 3.01,1.167 3.344,1.417 0.333,0.25 10 false 3 2.542,2.781 4.208,3.146 1.667,0.365 10 false BDR+ 3,2.771 3.208,3.01 0.208,0.24 10 false 1 2.552,3.458 4.219,3.823 1.667,0.365 10 false BDR- 3,3.458 3.24,3.74 0.24,0.281 10 false 2 3.615,2.854 4.01,3.167 0.396,0.313 10 false IM1 3.615,3.542 3.979,3.844 0.365,0.302 10 false IM1 3.656,2.677 4.115,2.99 0.458,0.313 10 false 22 3.656,3.344 3.958,3.563 0.302,0.219 10 false 40 4.344,2.781 6.01,3.146 1.667,0.365 10 false 2 4.344,3.458 4.656,3.74 0.313,0.281 10 false 1 4.521,2.771 5.135,3.063 0.615,0.292 10 false BDR+ 4.531,3.458 5.01,3.667 0.479,0.208 10 false BDR- 0.646,4.125 2.313,4.49 1.667,0.365 10 false M57 0.635,4.292 3.313,4.656 2.677,0.365 10 false No. 2 Side Airbag Sensor RH 4.479,4.115 6.146,4.479 1.667,0.365 10 false I5 4.469,4.271 6.615,4.625 2.146,0.354 10 false Door Side Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the door side airbag sensor RH and No. 2 side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the door side airbag sensor RH and No. 2 side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH

3.CHECK WIRE HARNESS
a.
C295812C46
0.833,0.625 1.25,0.875 0.417,0.25 0.521,3.615 0.885,3.865 0.365,0.25 0.948,4.146 1.375,3.771 true 2.052,4.167 1.656,3.76 true 1.531,4.385 1.531,4.219 false 1.448,1.24 1.76,0.781 true 2.219,1.24 1.938,0.781 true 1.448,2.344 1.448,1.906 1.448,1.906 1.24,1.906 false 1.958,2.771 1.958,2.469 false 0.552,2.333 1.042,2.781 0.49,0.448 10 false *1 2.719,2.333 3.208,2.802 0.49,0.469 10 false *2 1.469,4.385 1.854,4.667 0.385,0.281 10 false *5 0.635,0.177 1.073,0.656 0.438,0.479 10 false *a 0.354,3.167 0.792,3.813 0.438,0.646 10 false *b 2.385,2.333 2.875,2.802 0.49,0.469 10 false A 2.083,2.333 2.573,2.802 0.49,0.469 10 false B 1.74,2.333 2.229,2.802 0.49,0.469 10 false C 1.583,2.333 2.073,2.802 0.49,0.469 10 false D 1.229,2.333 1.719,2.802 0.49,0.469 10 false E 0.927,2.333 1.417,2.802 0.49,0.469 10 false F 1.26,1.26 1.802,1.531 0.542,0.271 10 false BDR+ 2.135,1.271 2.802,1.688 0.667,0.417 10 false BDR- 1.948,4.177 2.448,4.646 0.5,0.469 10 false BDR+ 0.792,4.177 1.292,4.51 0.5,0.333 10 false BDR- 0.917,0.667 1.458,0.938 0.542,0.271 10 false M57 0.646,3.656 1.188,3.927 0.542,0.271 10 false I5 1.042,1.833 1.427,2.115 0.385,0.281 10 false *3 1.896,2.792 2.281,3.073 0.385,0.281 10 false *4
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M57-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
M57-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M57-1 (BDR+) - M57-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M57-1 (BDR+) - M57-2 (BDR-) Always 1 MΩ or higher
M57-1 (BDR+) - Body ground Always 1 MΩ or higher
M57-2 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 2 SIDE AIRBAG SENSOR RH

NG

6.CHECK FLOOR WIRE
4.CHECK NO. 2 SIDE AIRBAG SENSOR RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 No. 2 Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the door side airbag sensor RH.


b.

Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B166D or B166E is output. A
DTC B167B or B167C is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.



A

5.CHECK DOOR SIDE AIRBAG SENSOR RH

B

C

5.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor RH


Interchange the door side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B166D or B166E is output. A
DTC B167B or B167C is output. B
DTCs B166D, B166E, B167B and B167C are not output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

6.CHECK FLOOR WIRE
a.
C284681C71
0.865,0.563 1.219,0.792 0.354,0.229 0.458,2.823 0.823,3.042 0.365,0.219 2.031,2.917 1.406,3.594 true 1.844,1.302 1.844,1.094 false 1.333,1.167 1.771,0.667 true 2.333,1.167 1.917,0.667 true 1.333,2.229 1.333,2.479 false 1.906,1.771 2.073,1.771 2.073,1.771 2.073,2.104 false 2.01,4.333 1.396,3.802 true 0.417,2.083 0.813,2.49 0.396,0.406 10 false *1 2.865,2.094 3.26,2.667 0.396,0.573 10 false *2 1.271,2.479 1.604,2.719 0.333,0.24 10 false *3 1.708,1.698 2.104,2.031 0.396,0.333 10 false *4 1.781,1.323 2.198,1.646 0.417,0.323 10 false *5 0.604,0.167 1,0.583 0.396,0.417 10 false *a 0.156,2.833 0.552,3.24 0.396,0.406 10 false *b 2.542,2.083 2.938,2.656 0.396,0.573 10 false A 2.24,2.083 2.635,2.656 0.396,0.573 10 false B 1.813,2.083 2.208,2.656 0.396,0.573 10 false C 1.521,2.083 1.917,2.656 0.396,0.573 10 false D 1.094,2.083 1.49,2.656 0.396,0.573 10 false E 0.792,2.083 1.188,2.656 0.396,0.573 10 false F 1.177,1.167 1.677,1.5 0.5,0.333 10 false BDR+ 2.198,1.167 2.698,1.5 0.5,0.333 10 false BDR- 2.083,4.25 2.583,4.5 0.5,0.25 10 false BDR- 2.083,2.823 2.615,3.083 0.531,0.26 10 false BDR+ 0.917,0.594 1.417,0.927 0.5,0.333 10 false M57 0.51,2.844 1,3.094 0.49,0.25 10 false IM1
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH)
*b Front view of wire harness connector
(to Front Door Wire RH)


Disconnect the floor wire connector from the front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IM1-22 (BDR+) - Body ground Power switch on (IG) Below 1 V
IM1-40 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IM1-22 (BDR+) - IM1-40 (BDR-) Always 1 MΩ or higher
IM1-22 (BDR+) - Body ground Always 1 MΩ or higher
IM1-40 (BDR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR WIRE RH

NG

REPLACE FLOOR WIRE