Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617  Lost Communication with Front Airbag Sensor LH  B1618  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1617 Lost Communication with Front Airbag Sensor LH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the front airbag sensor LH circuit.

·

The airbag sensor assembly detects a short to ground in the front airbag sensor LH circuit.

·

The airbag sensor assembly detects a short to B+ in the front airbag sensor LH circuit.

·

The airbag sensor assembly detects an open in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode
B1618 Front Airbag Sensor LH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the front airbag sensor LH circuit.

·

The airbag sensor assembly detects a short to ground in the front airbag sensor LH circuit.

·

The airbag sensor assembly detects a short to B+ in the front airbag sensor LH circuit.

·

The airbag sensor assembly detects an open in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B1617):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the front airbag sensor LH circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the front airbag sensor LH circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the front airbag sensor LH circuit - - ○ - - -
The airbag sensor assembly detects an open in the front airbag sensor LH circuit - - - ○ - -
Front airbag sensor LH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1618):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the front airbag sensor LH circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the front airbag sensor LH circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the front airbag sensor LH circuit - - ○ - - -
The airbag sensor assembly detects an open in the front airbag sensor LH circuit - - - ○ - -
Front airbag sensor LH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

B473428E61
4.781,2.896 6.854,3.365 2.073,0.469 10 false Airbag Sensor Assembly 4.771,2.729 5.375,2.917 0.604,0.188 10 false F150 4.583,1.021 5.042,1.323 0.458,0.302 10 false 30 4.583,1.698 5.333,2.073 0.75,0.375 10 false 31 4.833,1.021 5.292,1.323 0.458,0.302 10 false +SL 4.844,1.698 5.594,2.073 0.75,0.375 10 false -SL 5.479,1.448 6.156,1.74 0.677,0.292 10 false Interface 1.771,1.448 2.448,1.74 0.677,0.292 10 false Interface 0.76,1.448 1.438,1.74 0.677,0.292 10 false Element 3.75,1.125 4.208,1.427 0.458,0.302 10 false AF5 3.75,1.802 4.208,2.104 0.458,0.302 10 false AF5 3.833,0.938 4.292,1.24 0.458,0.302 10 false 2 3.833,1.615 4.292,1.917 0.458,0.302 10 false 1 3.042,1.021 3.5,1.323 0.458,0.302 10 false 2 3.042,1.708 3.5,2.01 0.458,0.302 10 false 1 2.667,1.021 3.125,1.323 0.458,0.302 10 false +SL 2.708,1.708 3.458,2.083 0.75,0.375 10 false -SL 0.563,2.344 0.906,2.521 0.344,0.177 10 false A7 0.563,2.521 2.635,2.99 2.073,0.469 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)
a.
B473431C18
0.802,0.76 1.219,1.01 0.417,0.25 0.5,3.719 0.854,3.938 0.354,0.219 1.792,1.74 1.792,1.573 false 1.458,1.594 1.76,1.219 true 2.146,1.594 1.844,1.219 true 0.896,4.26 1.24,3.833 true 1.781,4.25 1.448,3.833 true 1.156,2.615 1.156,2.25 1.156,2.25 0.979,2.25 false 1.792,3.031 1.792,2.74 false 0.302,2.594 0.729,3 0.427,0.406 10 false *1 2.729,2.604 3.104,3.052 0.375,0.448 10 false *2 1.708,1.75 2.063,2.073 0.354,0.323 10 false *c 0.635,0.188 1.042,0.521 0.406,0.333 10 false *a 0.375,3.406 0.719,3.667 0.344,0.26 10 false *b 2.354,2.604 2.729,3.052 0.375,0.448 10 false A 1.979,2.604 2.354,3.052 0.375,0.448 10 false B 1.521,2.604 1.896,3.052 0.375,0.448 10 false C 1.354,2.604 1.729,3.052 0.375,0.448 10 false D 0.885,2.604 1.26,3.052 0.375,0.448 10 false E 0.521,2.604 0.896,3.052 0.375,0.448 10 false F 0.854,0.802 1.271,1.063 0.417,0.26 10 false F150 1.302,1.594 1.656,1.917 0.354,0.323 10 false +SL 2.042,1.594 2.396,1.917 0.354,0.323 10 false -SL 0.594,3.74 0.844,3.906 0.25,0.167 10 false A7 1.667,4.26 2.021,4.583 0.354,0.323 10 false +SL 0.76,4.26 1.115,4.583 0.354,0.323 10 false -SL 0.823,2.167 1.167,2.427 0.344,0.26 10 false *3 1.719,3.052 2.094,3.5 0.375,0.448 10 false *4
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)
*c Service Wire


Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a service wire, connect terminals 30 (+SL) and 31 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-2 (+SL) - A7-1 (-SL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

NG

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)
a.
C398647C02
0.5,2.25 0.917,2.521 0.417,0.271 1.833,1.104 1.833,0.854 true 1.25,0.698 1.25,0.333 1.25,0.333 1.417,0.333 true 1.083,2.833 1.458,2.438 true 2,2.833 1.625,2.427 true 0.302,0.708 0.583,1 0.281,0.292 10 false *1 2.781,0.677 3.063,0.969 0.281,0.292 10 false *2 1.469,0.25 1.75,0.542 0.281,0.292 10 false *3 1.771,1.135 2.052,1.427 0.281,0.292 10 false *4 0.448,1.823 0.729,2.115 0.281,0.292 10 false *a 0.615,2.292 0.958,2.573 0.344,0.281 10 false A7 0.875,2.833 1.271,3.135 0.396,0.302 10 false -SL 1.958,2.844 2.354,3.146 0.396,0.302 10 false +SL 2.333,0.688 2.5,0.917 0.167,0.229 10 false A 2.031,0.688 2.198,0.917 0.167,0.229 10 false B 1.573,0.688 1.74,0.917 0.167,0.229 10 false C 1.406,0.688 1.573,0.917 0.167,0.229 10 false D 0.969,0.688 1.135,0.917 0.167,0.229 10 false E 0.646,0.688 0.813,0.917 0.167,0.229 10 false F
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-2 (+SL) - A7-1 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
a.
C398647C02
0.5,2.25 0.917,2.521 0.417,0.271 1.833,1.104 1.833,0.854 true 1.25,0.698 1.25,0.333 1.25,0.333 1.417,0.333 true 1.083,2.833 1.458,2.438 true 2,2.833 1.625,2.427 true 0.302,0.708 0.583,1 0.281,0.292 10 false *1 2.781,0.677 3.063,0.969 0.281,0.292 10 false *2 1.469,0.25 1.75,0.542 0.281,0.292 10 false *3 1.771,1.135 2.052,1.427 0.281,0.292 10 false *4 0.448,1.823 0.729,2.115 0.281,0.292 10 false *a 0.615,2.292 0.958,2.573 0.344,0.281 10 false A7 0.875,2.833 1.271,3.135 0.396,0.302 10 false -SL 1.958,2.844 2.354,3.146 0.396,0.302 10 false +SL 2.333,0.688 2.5,0.917 0.167,0.229 10 false A 2.031,0.688 2.198,0.917 0.167,0.229 10 false B 1.573,0.688 1.74,0.917 0.167,0.229 10 false C 1.406,0.688 1.573,0.917 0.167,0.229 10 false D 0.969,0.688 1.135,0.917 0.167,0.229 10 false E 0.646,0.688 0.813,0.917 0.167,0.229 10 false F
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-2 (+SL) - Body ground Power switch on (IG) Below 1 V
A7-1 (-SL) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)
a.
C398647C02
0.5,2.25 0.917,2.521 0.417,0.271 1.833,1.104 1.833,0.854 true 1.25,0.698 1.25,0.333 1.25,0.333 1.417,0.333 true 1.083,2.833 1.458,2.438 true 2,2.833 1.625,2.427 true 0.302,0.708 0.583,1 0.281,0.292 10 false *1 2.781,0.677 3.063,0.969 0.281,0.292 10 false *2 1.469,0.25 1.75,0.542 0.281,0.292 10 false *3 1.771,1.135 2.052,1.427 0.281,0.292 10 false *4 0.448,1.823 0.729,2.115 0.281,0.292 10 false *a 0.615,2.292 0.958,2.573 0.344,0.281 10 false A7 0.875,2.833 1.271,3.135 0.396,0.302 10 false -SL 1.958,2.844 2.354,3.146 0.396,0.302 10 false +SL 2.333,0.688 2.5,0.917 0.167,0.229 10 false A 2.031,0.688 2.198,0.917 0.167,0.229 10 false B 1.573,0.688 1.74,0.917 0.167,0.229 10 false C 1.406,0.688 1.573,0.917 0.167,0.229 10 false D 0.969,0.688 1.135,0.917 0.167,0.229 10 false E 0.646,0.688 0.813,0.917 0.167,0.229 10 false F
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Front Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-2 (+SL) - Body ground Always 1 MΩ or higher
A7-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT AIRBAG SENSOR LH

NG

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR LH
a.
C238386C08
2.083,1.01 2.448,1.5 0.365,0.49 10 A 1.927,1.01 2.427,1.479 0.5,0.469 10 B 1.583,1.01 1.969,1.521 0.385,0.51 10 C 1.427,1.01 1.844,1.583 0.417,0.573 10 D 1.083,1.01 1.531,1.667 0.448,0.656 10 E 0.938,1.01 1.521,1.75 0.583,0.74 10 F 0.563,1.021 1.125,1.594 0.563,0.573 10 *1 2.542,1.031 2.885,1.563 0.344,0.531 10 *2
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1612, B1613, B1617 and B1618 are not output. A
DTC B1617 or B1618 is output. B
DTC B1612 or B1613 is output. C


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C398648C02
0.75,2.115 1.167,2.417 0.417,0.302 1.167,1.021 1.167,0.771 true 2,1.021 2,0.771 true 1.333,1.917 1.75,2.177 true 2.333,1.917 1.948,2.177 true 0.24,0.604 0.5,0.917 0.26,0.313 10 false *1 2.823,0.604 3.083,0.917 0.26,0.313 10 false *2 1.083,1.052 1.344,1.365 0.26,0.313 10 false *3 1.938,1.042 2.198,1.354 0.26,0.313 10 false *4 0.74,1.667 1,2 0.26,0.333 10 false *a 0.833,2.188 1.167,2.5 0.333,0.313 10 false AF5 1.083,1.698 1.583,1.917 0.5,0.219 10 false +SL 2.333,1.698 2.76,2 0.427,0.302 10 false -SL 0.573,0.594 0.833,0.906 0.26,0.313 10 false F 0.885,0.594 1.146,0.906 0.26,0.313 10 false E 1.344,0.594 1.604,0.906 0.26,0.313 10 false D 1.656,0.594 1.917,0.906 0.26,0.313 10 false C 2.104,0.594 2.365,0.906 0.26,0.313 10 false B 2.417,0.594 2.677,0.906 0.26,0.313 10 false A
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - Body ground Always 1 MΩ or higher
AF5-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C398648C02
0.75,2.115 1.167,2.417 0.417,0.302 1.167,1.021 1.167,0.771 true 2,1.021 2,0.771 true 1.333,1.917 1.75,2.177 true 2.333,1.917 1.948,2.177 true 0.24,0.604 0.5,0.917 0.26,0.313 10 false *1 2.823,0.604 3.083,0.917 0.26,0.313 10 false *2 1.083,1.052 1.344,1.365 0.26,0.313 10 false *3 1.938,1.042 2.198,1.354 0.26,0.313 10 false *4 0.74,1.667 1,2 0.26,0.333 10 false *a 0.833,2.188 1.167,2.5 0.333,0.313 10 false AF5 1.083,1.698 1.583,1.917 0.5,0.219 10 false +SL 2.333,1.698 2.76,2 0.427,0.302 10 false -SL 0.573,0.594 0.833,0.906 0.26,0.313 10 false F 0.885,0.594 1.146,0.906 0.26,0.313 10 false E 1.344,0.594 1.604,0.906 0.26,0.313 10 false D 1.656,0.594 1.917,0.906 0.26,0.313 10 false C 2.104,0.594 2.365,0.906 0.26,0.313 10 false B 2.417,0.594 2.677,0.906 0.26,0.313 10 false A
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AF5-2 (+SL) - Body ground Power switch on (IG) Below 1 V
AF5-1 (-SL) - Body ground Power switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C398648C02
0.75,2.115 1.167,2.417 0.417,0.302 1.167,1.021 1.167,0.771 true 2,1.021 2,0.771 true 1.333,1.917 1.75,2.177 true 2.333,1.917 1.948,2.177 true 0.24,0.604 0.5,0.917 0.26,0.313 10 false *1 2.823,0.604 3.083,0.917 0.26,0.313 10 false *2 1.083,1.052 1.344,1.365 0.26,0.313 10 false *3 1.938,1.042 2.198,1.354 0.26,0.313 10 false *4 0.74,1.667 1,2 0.26,0.333 10 false *a 0.833,2.188 1.167,2.5 0.333,0.313 10 false AF5 1.083,1.698 1.583,1.917 0.5,0.219 10 false +SL 2.333,1.698 2.76,2 0.427,0.302 10 false -SL 0.573,0.594 0.833,0.906 0.26,0.313 10 false F 0.885,0.594 1.146,0.906 0.26,0.313 10 false E 1.344,0.594 1.604,0.906 0.26,0.313 10 false D 1.656,0.594 1.917,0.906 0.26,0.313 10 false C 2.104,0.594 2.365,0.906 0.26,0.313 10 false B 2.417,0.594 2.677,0.906 0.26,0.313 10 false A
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - AF5-1 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
B473432C19
0.792,0.792 1.208,1.031 0.417,0.24 1.104,3.729 1.438,3.938 0.333,0.208 1.802,1.719 1.802,1.542 false 1.458,1.542 1.76,1.198 true 2.135,1.542 1.833,1.198 true 1.854,2.573 1.854,2.073 1.854,2.073 1.604,2.073 false 1.104,3.042 1.104,2.708 false 1.5,3.5 1.896,3.729 true 2.125,3.719 2.333,3.479 true 0.302,2.573 0.688,2.854 0.385,0.281 10 false *1 2.74,2.563 3.281,3.104 0.542,0.542 10 false *2 1.729,1.719 2.125,1.979 0.396,0.26 10 false *c 1.042,3.063 1.417,3.333 0.375,0.271 10 false *3 1.448,2.01 1.927,2.417 0.479,0.406 10 false *4 0.656,0.188 1.042,0.49 0.385,0.302 10 false *a 0.76,3.385 1.135,3.75 0.375,0.365 10 false *b 2.344,2.563 2.885,3.104 0.542,0.542 10 false A 2.052,2.563 2.594,3.104 0.542,0.542 10 false B 1.583,2.563 2.125,3.104 0.542,0.542 10 false C 1.292,2.563 1.833,3.104 0.542,0.542 10 false D 0.823,2.563 1.365,3.104 0.542,0.542 10 false E 0.521,2.563 1.063,3.104 0.542,0.542 10 false F 0.844,0.813 1.188,1.01 0.344,0.198 10 false F150 1.292,1.552 1.833,1.917 0.542,0.365 10 false +SL 2.042,1.552 2.583,1.917 0.542,0.365 10 false -SL 1.146,3.75 1.479,3.958 0.333,0.208 10 false AF5 1.219,3.417 1.604,3.719 0.385,0.302 10 false +SL 2.396,3.396 2.667,3.729 0.271,0.333 10 false -SL
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)
*c Service Wire


Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-2 (+SL) - AF5-1 (-SL) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE